Installation Manual
Table Of Contents
- Title Page
- Table of Contents
- Certifications, approvals, listings, and safety
- Introduction
- System overview
- Installation checklist
- Control panel installation
- Power supply
- Telephone communications
- IP communications
- Keypads, keyswitches, keyfobs and transmitters
- Keypads
- B915 Basic Keypad
- B920 Two-line Alphanumeric Keypad
- B921C Two-line Capacitive Keypad with Inputs
- B930 ATM Style Alphanumeric Keypad
- B942 Touch Screen Keypad
- Shortcuts and custom functions
- Address settings
- Supervision
- Installation and control panel wiring (keypads)
- Sensor loops overview and wiring (B921C/B942/B942W only)
- Output wiring (B942/B942W only)
- Troubleshooting
- Keyswitches
- RADION keyfobs and Inovonics pendant transmitters
- Keypads
- On-board outputs
- Off-board outputs
- On-board points
- Off-board points
- Wireless modules
- Access control
- Program and test the control panel
- Control panel board overview
- System wiring diagrams
- Approved applications
- Keypad Installer menu
- [1] Program menu
- [1] Reporting > [1] Phone menu parameters
- [1] Reporting > [2] Network menu parameters
- [1] Reporting > [3] Routing menu parameters
- [1] Reporting > [4] Personal Note menu parameters
- [2] Network > [1] Ethernet > (choose the bus module or on-board) > [1] Module Parameters menu
- [2] Network > [1] Ethernet > (choose the bus module or on-board) > [2] Address Parameters menu
- [2] Network > [1] Ethernet > (choose the bus module or on-board) > [3] DNS Parameters menu
- [2] Network > [2] Cellular > (choose the SDI2 cellular module or plug-in module)
- [3] RPS > [1] RPS Passcode menu parameters
- [3] RPS > [2] RPS Phone Number menu parameters
- [3] RPS > [3] RPS IP Address menu parameters
- [3] RPS > [4] RPS Port Number menu parameters
- [4] Area Options menu parameters
- [5] Keypad menu parameters
- [6] Users menu parameters
- [7] Points menu parameters
- [8] Disable Programming menu
- [2] Wireless menu
- [1] RF Point Menu> [1] Enroll Point RFID
- [1] RF Point Menu> [2] Replace Point RFID
- [1] RF Point Menu> [3] Remove Point RFID
- [2] RF Repeater Menu > [1] Add Repeater
- [2] RF Repeater Menu > [2] Replace Repeater
- [2] RF Repeater Menu > [3] Remove Repeater
- [3] RF Diagnostic Menu > [1] RF Points
- [3] RF Diagnostic Menu > [2] RF Repeater Menu
- [3] Diags menu
- [4] Serv Byp (Service Bypass) menu
- [5] Versions menu
- [6] Cloud menu
- [1] Program menu
- Specifications
- Appendix
- Back Page
4. Press [Edit] to change the passcode.
5. Delete existing characters, if necessary, and then enter the new characters.
6. Press [Save].
7. When the keypad shows Parameter Saved, escape from the menu.
User (Passcode) Worksheet (Includes users added only through RPS or the Main menu
User ### Passcode User
group
Area authority
1 ￚￚￚￚ 2 ￚￚￚￚ 3* ￚￚￚￚ 4*
User name
000 123 __ __ __ ____ 15 15 15 15 SERVICE PASSCODE
001 123456 ____ 1 __ __ __ USER 1
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
__ __ __ __ __ __ __ __ __ ____ __ __ __ __ USER __ __
* Applicable to B5512 only.
[7] Points menu parameters
Use the parameters in this menu to assign a Point Source and a Point Index to each point.
The Point Source parameter assigns the point to a device (on-board, Octo-input, and wireless
are examples). The Point Index (point profile) determines how the point operates.
20.1.16
126 en | Keypad Installer menu Control Panel
2016.05 | 14 | F.01U.287.180 Installation and System Reference Guide Bosch Security Systems, Inc.