Installation Manual
Table Of Contents
- Title Page
- Table of Contents
- Certifications, approvals, listings, and safety
- Introduction
- System overview
- Installation checklist
- Control panel installation
- Power supply
- Telephone communications
- IP communications
- Keypads, keyswitches, keyfobs and transmitters
- Keypads
- B915 Basic Keypad
- B920 Two-line Alphanumeric Keypad
- B921C Two-line Capacitive Keypad with Inputs
- B930 ATM Style Alphanumeric Keypad
- B942 Touch Screen Keypad
- Shortcuts and custom functions
- Address settings
- Supervision
- Installation and control panel wiring (keypads)
- Sensor loops overview and wiring (B921C/B942/B942W only)
- Output wiring (B942/B942W only)
- Troubleshooting
- Keyswitches
- RADION keyfobs and Inovonics pendant transmitters
- Keypads
- On-board outputs
- Off-board outputs
- On-board points
- Off-board points
- Wireless modules
- Access control
- Program and test the control panel
- Control panel board overview
- System wiring diagrams
- Approved applications
- Keypad Installer menu
- [1] Program menu
- [1] Reporting > [1] Phone menu parameters
- [1] Reporting > [2] Network menu parameters
- [1] Reporting > [3] Routing menu parameters
- [1] Reporting > [4] Personal Note menu parameters
- [2] Network > [1] Ethernet > (choose the bus module or on-board) > [1] Module Parameters menu
- [2] Network > [1] Ethernet > (choose the bus module or on-board) > [2] Address Parameters menu
- [2] Network > [1] Ethernet > (choose the bus module or on-board) > [3] DNS Parameters menu
- [2] Network > [2] Cellular > (choose the SDI2 cellular module or plug-in module)
- [3] RPS > [1] RPS Passcode menu parameters
- [3] RPS > [2] RPS Phone Number menu parameters
- [3] RPS > [3] RPS IP Address menu parameters
- [3] RPS > [4] RPS Port Number menu parameters
- [4] Area Options menu parameters
- [5] Keypad menu parameters
- [6] Users menu parameters
- [7] Points menu parameters
- [8] Disable Programming menu
- [2] Wireless menu
- [1] RF Point Menu> [1] Enroll Point RFID
- [1] RF Point Menu> [2] Replace Point RFID
- [1] RF Point Menu> [3] Remove Point RFID
- [2] RF Repeater Menu > [1] Add Repeater
- [2] RF Repeater Menu > [2] Replace Repeater
- [2] RF Repeater Menu > [3] Remove Repeater
- [3] RF Diagnostic Menu > [1] RF Points
- [3] RF Diagnostic Menu > [2] RF Repeater Menu
- [3] Diags menu
- [4] Serv Byp (Service Bypass) menu
- [5] Versions menu
- [6] Cloud menu
- [1] Program menu
- Specifications
- Appendix
- Back Page
RFID
B91x/B92x keypads configuration of RFID
1. Enter the installer passcode, and then open the [1] Installer menu.
2. Go to [1] Program > [7] Points option. The keypad toggles between showing the point
index and point source for the selected point.
3. Use [PREV] or [NEXT] to go to the desired point, or enter the point number.
4. Press [ENTER] to edit the point and then press [NEXT] to go to the RFID option if the
source is Wireless.
5. Press [ENTER] to edit the RFID for the selected.
6. Delete existing characters, if necessary, and then enter the new numbers listed on the
wireless device.
7. Press [ENTER] while viewing the desired source to save the programming.
8. When the keypad shows Parameter Saved, escape from the menu.
B93x/B94x keypads configuration of RFID
1. Enter the installer passcode, and then open the [1] Installer menu.
2. Go to [1] Program > [7] Points option. The keypad shows the index for the selected
point.
3. Use
/[PREV] or /[NEXT] to go to the desired point, or enter the point number.
4. Press [Source] to view and edit the source. If the source is Wireless, the [RFID] softkey
appears.
5. Press [RFID] to edit the RFID.
6. Delete existing characters, if necessary, and then enter the new numbers listed on the
wireless device.
7. Press [Save] to save the programming.
8. When the keypad shows Parameter Saved, escape from the menu.
[8] Disable Programming menu
The Keypad Installer menu is enabled by default. When enabled, the Service User (Authority
Level 15) has authority to access the menus. If you disable Keypad Programming, the Service
User cannot access the menus. In this menu, you can disable Keypad Programming.
Notice!
You can continue using the current programming session. Disabling Keypad Programming
applies once you exit the current session.
Keypad Programming
B91x/B92x keypads configuration of Keypad Programming
1. Enter the installer passcode, and then open the [1] Installer menu.
2. Go to [1] Program > [8] Disable Programming. The keypad shows that programming is
enabled.
3. Press [ENTER] to disable keypad programming, and then press [NEXT] to go to the No
option.
4. Press [ENTER] to save the programming.
5. When the keypad shows Parameter Saved, escape from the menu.
20.1.17
Control Panel Keypad Installer menu | en 135
Bosch Security Systems, Inc. Installation and System Reference Guide 2016.05 | 14 | F.01U.287.180