Installation Manual
Table Of Contents
- Title Page
- Table of Contents
- Certifications, approvals, listings, and safety
- Introduction
- System overview
- Installation checklist
- Control panel installation
- Power supply
- Telephone communications
- IP communications
- Keypads, keyswitches, keyfobs and transmitters
- Keypads
- B915 Basic Keypad
- B920 Two-line Alphanumeric Keypad
- B921C Two-line Capacitive Keypad with Inputs
- B930 ATM Style Alphanumeric Keypad
- B942 Touch Screen Keypad
- Shortcuts and custom functions
- Address settings
- Supervision
- Installation and control panel wiring (keypads)
- Sensor loops overview and wiring (B921C/B942/B942W only)
- Output wiring (B942/B942W only)
- Troubleshooting
- Keyswitches
- RADION keyfobs and Inovonics pendant transmitters
- Keypads
- On-board outputs
- Off-board outputs
- On-board points
- Off-board points
- Wireless modules
- Access control
- Program and test the control panel
- Control panel board overview
- System wiring diagrams
- Approved applications
- Keypad Installer menu
- [1] Program menu
- [1] Reporting > [1] Phone menu parameters
- [1] Reporting > [2] Network menu parameters
- [1] Reporting > [3] Routing menu parameters
- [1] Reporting > [4] Personal Note menu parameters
- [2] Network > [1] Ethernet > (choose the bus module or on-board) > [1] Module Parameters menu
- [2] Network > [1] Ethernet > (choose the bus module or on-board) > [2] Address Parameters menu
- [2] Network > [1] Ethernet > (choose the bus module or on-board) > [3] DNS Parameters menu
- [2] Network > [2] Cellular > (choose the SDI2 cellular module or plug-in module)
- [3] RPS > [1] RPS Passcode menu parameters
- [3] RPS > [2] RPS Phone Number menu parameters
- [3] RPS > [3] RPS IP Address menu parameters
- [3] RPS > [4] RPS Port Number menu parameters
- [4] Area Options menu parameters
- [5] Keypad menu parameters
- [6] Users menu parameters
- [7] Points menu parameters
- [8] Disable Programming menu
- [2] Wireless menu
- [1] RF Point Menu> [1] Enroll Point RFID
- [1] RF Point Menu> [2] Replace Point RFID
- [1] RF Point Menu> [3] Remove Point RFID
- [2] RF Repeater Menu > [1] Add Repeater
- [2] RF Repeater Menu > [2] Replace Repeater
- [2] RF Repeater Menu > [3] Remove Repeater
- [3] RF Diagnostic Menu > [1] RF Points
- [3] RF Diagnostic Menu > [2] RF Repeater Menu
- [3] Diags menu
- [4] Serv Byp (Service Bypass) menu
- [5] Versions menu
- [6] Cloud menu
- [1] Program menu
- Specifications
- Appendix
- Back Page
– Enabled on Cellular
– Enabled on Ethernet and Cellular
4. Press /[NEXT]. The keypad shows the Cloud Certificate status, which is one of the
following:
– Not Installed
– Certificate Valid
5. Press
/[NEXT]. The keypad shows the Cloud state, which is one of the following:
– Connected (and through which method)
– Not Ready
– Disconnected
– Not Available
– Trying to Connect
6. When finished viewing the information, escape from the menu.
[4] Serv Byp (Service Bypass) menu
In this menu, you can edit the Service Bypass points.
Service Bypass
B91x/B92x keypads use of Service Bypass to bypass points
1. Enter the installer passcode, and then open the [1] Installer menu.
2. Go to [4] Srvc Byp. If no points have been bypassed the keypad shows No points
bypassed. If points are bypassed, the keypad lists the number of bypassed points.
3. Enter number for the point to bypass, and then press [ENTER] to select the point.
4. Press [ENTER] to bypass the point. The keypad shows Parameter Saved, and then returns
to the point you just bypassed.
5. Escape from the menu.
B93x/B94x keypads use of Service Bypass to bypass points
1. Enter the installer passcode, and then open the [1] Installer menu.
2. Go to [4] Srvc Byp menu. If no points have been bypassed the keypad shows No points
bypassed. If points are bypassed, the keypad lists the number of bypassed points.
3. Enter number for the point to bypass, and then press [ENTER].
4. Press [Bypass] to bypass the point. The keypad shows Parameter Saved, and then returns
to the point you just bypassed.
5. Escape from the menu.
[5] Versions menu
Use the Versions menu to view control panel version information.
Versions
B91x/B92x keypads use of Versions
1. Enter the installer passcode, and then open the [1] Installer menu.
2. Go to [5] Versions.
3. Use [PREV] or [NEXT] to cycle through the list of items for which you can view the
version.
4. Press [ENTER] to view the version.
5. Escape from the menu.
20.4
20.5
144 en | Keypad Installer menu Control Panel
2016.05 | 14 | F.01U.287.180 Installation and System Reference Guide Bosch Security Systems, Inc.