Installation Manual
Table Of Contents
- Title Page
- Table of Contents
- Certifications, approvals, listings, and safety
- Introduction
- System overview
- Installation checklist
- Control panel installation
- Power supply
- Telephone communications
- IP communications
- Keypads, keyswitches, keyfobs and transmitters
- Keypads
- B915 Basic Keypad
- B920 Two-line Alphanumeric Keypad
- B921C Two-line Capacitive Keypad with Inputs
- B930 ATM Style Alphanumeric Keypad
- B942 Touch Screen Keypad
- Shortcuts and custom functions
- Address settings
- Supervision
- Installation and control panel wiring (keypads)
- Sensor loops overview and wiring (B921C/B942/B942W only)
- Output wiring (B942/B942W only)
- Troubleshooting
- Keyswitches
- RADION keyfobs and Inovonics pendant transmitters
- Keypads
- On-board outputs
- Off-board outputs
- On-board points
- Off-board points
- Wireless modules
- Access control
- Program and test the control panel
- Control panel board overview
- System wiring diagrams
- Approved applications
- Keypad Installer menu
- [1] Program menu
- [1] Reporting > [1] Phone menu parameters
- [1] Reporting > [2] Network menu parameters
- [1] Reporting > [3] Routing menu parameters
- [1] Reporting > [4] Personal Note menu parameters
- [2] Network > [1] Ethernet > (choose the bus module or on-board) > [1] Module Parameters menu
- [2] Network > [1] Ethernet > (choose the bus module or on-board) > [2] Address Parameters menu
- [2] Network > [1] Ethernet > (choose the bus module or on-board) > [3] DNS Parameters menu
- [2] Network > [2] Cellular > (choose the SDI2 cellular module or plug-in module)
- [3] RPS > [1] RPS Passcode menu parameters
- [3] RPS > [2] RPS Phone Number menu parameters
- [3] RPS > [3] RPS IP Address menu parameters
- [3] RPS > [4] RPS Port Number menu parameters
- [4] Area Options menu parameters
- [5] Keypad menu parameters
- [6] Users menu parameters
- [7] Points menu parameters
- [8] Disable Programming menu
- [2] Wireless menu
- [1] RF Point Menu> [1] Enroll Point RFID
- [1] RF Point Menu> [2] Replace Point RFID
- [1] RF Point Menu> [3] Remove Point RFID
- [2] RF Repeater Menu > [1] Add Repeater
- [2] RF Repeater Menu > [2] Replace Repeater
- [2] RF Repeater Menu > [3] Remove Repeater
- [3] RF Diagnostic Menu > [1] RF Points
- [3] RF Diagnostic Menu > [2] RF Repeater Menu
- [3] Diags menu
- [4] Serv Byp (Service Bypass) menu
- [5] Versions menu
- [6] Cloud menu
- [1] Program menu
- Specifications
- Appendix
- Back Page
Keypads, keyswitches, keyfobs and transmitters
The system can use keypads, maintained or momentary contact keyswitches, wireless RADION
keyfobs or Inovonics transmitters, or a combination of these options to turn areas on and off.
B5512 control panels support up to 4 areas. B4512 control panels support up to 2 areas.
B3512 control panels support 1 area.
Refer to Areas and accounts, page 20 for a description of areas.
Keypads
Keypads are four-wire powered devices used to operate the system (turn areas on or off for
example) and show system status.
B5512/B4512 control panels support up to 8 keypads, in any combination of SDI2 keypad
models. The B3512 supports up to 4 keypads.
SDI2 keypads connect to the SDI2 bus on the control panel using terminals PWR, A, B, and
COM.
You can connect more than one keypad to the control panel by wiring them in parallel.
The control panel sends a trouble report if it loses communication with a keypad and a
message appears on all keypads.
All SDI2 keypads have:
– User-adjustable volume
– Keypress tones
– A nightlight feature
– A display that shows system messages
– A sounder that emits warning tones
– Highly visible status indicators
– Backlit keys, with seven configurable backlight settings ranging from 0% to 100%
This section includes basic installation instructions for compatible keypads. For detailed
installation instructions, refer to the corresponding keypad document listed in Keypad
documents, page 12.
B915 Basic Keypad
The B915 Basic Keypad is an SDI2 bus compatible device. It offers the same commands and
menu structure as the other B Series intrusion keypads.
B920 Two-line Alphanumeric Keypad
The B920 Two-line Alphanumeric Keypad (SDI2) is an SDI2 bus compatible device. The display
shows two lines, 18 characters per line. Each keypad has 10 number keys and seven function
keys.
B921C Two-line Capacitive Keypad with Inputs
The B921C Two-line Capacitive Keypad is an SDI2 bus compatible device. The keypad features
capacitive keys.
Each sensor loop is assigned a point number. The keypad transmits sensor loop status to the
control panel individually. The control panel detects open, short, and normal circuit conditions
on the keypad sensor loops.
B930 ATM Style Alphanumeric Keypad
The B930 ATM Style Alphanumeric Keypad (SDI2) is an SDI2 bus compatible device. The
keypad features a bright five line display and eight softkeys.
9
9.1
9.1.1
9.1.2
9.1.3
9.1.4
54 en | Keypads, keyswitches, keyfobs and transmitters Control Panel
2016.05 | 14 | F.01U.287.180 Installation and System Reference Guide Bosch Security Systems, Inc.