Installation Manual
Table Of Contents
- Title Page
- Table of Contents
- Certifications, approvals, listings, and safety
- Introduction
- System overview
- Installation checklist
- Control panel installation
- Power supply
- Telephone communications
- IP communications
- Keypads, keyswitches, keyfobs and transmitters
- Keypads
- B915 Basic Keypad
- B920 Two-line Alphanumeric Keypad
- B921C Two-line Capacitive Keypad with Inputs
- B930 ATM Style Alphanumeric Keypad
- B942 Touch Screen Keypad
- Shortcuts and custom functions
- Address settings
- Supervision
- Installation and control panel wiring (keypads)
- Sensor loops overview and wiring (B921C/B942/B942W only)
- Output wiring (B942/B942W only)
- Troubleshooting
- Keyswitches
- RADION keyfobs and Inovonics pendant transmitters
- Keypads
- On-board outputs
- Off-board outputs
- On-board points
- Off-board points
- Wireless modules
- Access control
- Program and test the control panel
- Control panel board overview
- System wiring diagrams
- Approved applications
- Keypad Installer menu
- [1] Program menu
- [1] Reporting > [1] Phone menu parameters
- [1] Reporting > [2] Network menu parameters
- [1] Reporting > [3] Routing menu parameters
- [1] Reporting > [4] Personal Note menu parameters
- [2] Network > [1] Ethernet > (choose the bus module or on-board) > [1] Module Parameters menu
- [2] Network > [1] Ethernet > (choose the bus module or on-board) > [2] Address Parameters menu
- [2] Network > [1] Ethernet > (choose the bus module or on-board) > [3] DNS Parameters menu
- [2] Network > [2] Cellular > (choose the SDI2 cellular module or plug-in module)
- [3] RPS > [1] RPS Passcode menu parameters
- [3] RPS > [2] RPS Phone Number menu parameters
- [3] RPS > [3] RPS IP Address menu parameters
- [3] RPS > [4] RPS Port Number menu parameters
- [4] Area Options menu parameters
- [5] Keypad menu parameters
- [6] Users menu parameters
- [7] Points menu parameters
- [8] Disable Programming menu
- [2] Wireless menu
- [1] RF Point Menu> [1] Enroll Point RFID
- [1] RF Point Menu> [2] Replace Point RFID
- [1] RF Point Menu> [3] Remove Point RFID
- [2] RF Repeater Menu > [1] Add Repeater
- [2] RF Repeater Menu > [2] Replace Repeater
- [2] RF Repeater Menu > [3] Remove Repeater
- [3] RF Diagnostic Menu > [1] RF Points
- [3] RF Diagnostic Menu > [2] RF Repeater Menu
- [3] Diags menu
- [4] Serv Byp (Service Bypass) menu
- [5] Versions menu
- [6] Cloud menu
- [1] Program menu
- Specifications
- Appendix
- Back Page
B450 Conettix Plug-in
Communicator Interface
Opt. Opt. Opt. Opt. Opt. Opt. Opt.
B520 Auxiliary Power Supply
Module
Opt. Opt. Opt. Opt. Opt. Opt. Opt.
B810 RADION receiver SD Opt. Opt. Opt. Opt. Opt. Opt. Opt.
B820 SDI2 Inovonics
Interface Module
Opt. Opt. Opt. Opt. Opt. Opt. Opt.
B901 Access Control
Module
3
Opt. Opt. Opt. Opt. Opt. Opt. Opt.
B915/B915I Basic Keypad 1+ 1+ 1+ 1+ 1+ 1+ Opt.
B920 Two-line Alphanumeric
Keypad (SDI2)
1+ 1+ 1+ 1+ 1+ 1+ Opt.
B921C Two-line Capacitive
Keypad
1+ 1+ 1+ 1+ 1+ 1+ Opt.
B930 keypads 1+ 1+ 1+ 1+ 1+ 1+ Opt.
B942/B942W Touch Screen
Keypad
1+ 1+ 1+ 1+ 1+ 1+ Opt.
CX4010 Plug-in Transformer
(18 VAC 22 VA 60 Hz)
Required for all applications. Opt.
D125B Dual Class B Initiating
Module
Opt. Opt. Opt. Opt. Opt. Opt. Opt.
D126 Standby Battery (12 V,
7 Ah)
Opt. Opt. Opt. Opt. Opt. Opt. Opt.
D130 Auxiliary Relay Module Opt. Opt. Opt. Opt. Opt. Opt. Opt.
D133 Single Relay Module Opt. Opt. Opt. Opt. Opt. Opt. Opt.
D134 Dual Relay Module Opt. Opt. Opt. Opt. Opt. Opt. Opt.
D1218 Battery (12 V, 18 Ah) Opt. Opt. Opt. Opt. Opt. Opt. Opt.
D192G Class “B”, Style Y
Bell Circuit Supervision
Opt. Req. Opt. Opt. Opt. Opt. Opt.
D8004 Transformer
Enclosure
Opt. Opt. Opt. Opt. Opt. Opt. Opt.
D8108A Attack Resistant
Enclosure or D8109 Fire
Enclosure
Opt. Opt. Opt. Opt. No Opt. Opt.
D8108A Attack Resistant
Enclosure
1
Opt. Opt. Opt. Opt. Opt. Opt. Opt.
98 en | Approved applications Control Panel
2016.05 | 14 | F.01U.287.180 Installation and System Reference Guide Bosch Security Systems, Inc.