Installation Guide
4
en
–
Included in delivery
a
b Installation instructions
c Assembly bracket
d Transformer mount
e Spacers
f 7 fastening screws (silver)
g 2 fastening screws (long/black)
h 1 sleeve (black)
i 2 fastening screws (short/black)
j 2 sleeves (white)
k Transformer
Prepare built-in units
Important: The power outlet must be located outside the
built-in cut-out.
Make sure there is adequate aeration. To do this, remove
the rear panel or cut out an opening of 19
11
16
3
4
. There must be a gap of at least 1
3
8 (35 mm)
between the wall and base of the unit or the rear panel of the
unit situated above. The ventilation slots and intake openings
must not be covered. Also follow the installation instructions for
the appliance situated above or below. If installing the appliance
above a warming drawer, the height of the recess must be 23
1
4
(590 mm). If the appliance is installed directly under a décor
panel, ensure that there is a ventilation slot of at least 31 square
inches (200 cm
2
). The ideal installation height for the fully
edge of the appliance, is 37
7
16.
damaged.
¡
CAUTION
Installation must always be performed by 2 persons.
Installation preparation
Unpack all the parts and check for any damage in transit. Do
not operate a damaged appliance.
1 Take note of the installation dimensions of the particular
model.
Important: Two openings angles can be selected for the
door. Depending on the opening angle required, the mounting
distance to the wall should be observed before installation.
= mounting distance to the wall at least 13
3
4 (350 mm).
= mounting distance to the wall at least 25
9
16 (650 mm).
top and bottom of the hinge.
2 Remove the installation template on the back of the
installation instructions. Place the installation template at the
front edge of the unit and screw on the assembly bracket c
as shown with two fastening screws f. The assembly
bracket must be positioned at the base of the unit and the
wall such that no gap is present.
3 Fasten the the transformer mount d with two screws f in
the middle.
4 Insert the transformer in the mount. The connections to both
lines must point to the left.
Note: When positioning the transformer k and pushing in the
appliance, do not trap the lines.
The transformer k is not allowed to touch the appliance and
the back wall of the cupboard.
5 Set the mains switch U to h on the appliance.
6 Securely insert the front line into the appliance (snaps into
place). For this purpose, put the appliance to be plugged
in just on to the edge of the unit. Plug the power cord into
the socket. Plug transformer into dedicated receptacle in an
on the built-in situation). Do not plug into a receptacle
behind the appliance.
7 Push the appliance into the unit until it clicks into place.
Check that the appliance is in the middle. If necessary,
align the appliance. To do so, pull the appliance out a little,
remove the appropriate spacers e and attach to the left
side (top and bottom). Push the appliance into the unit until
it clicks into place.
8
outlet and open. Remove the drip tray Y. Pull the cover X on
the bottom left-hand side forwards and remove. Pull out the
accessories drawer Z and put to one side.
9 First, screw on the appliance as shown using 2 of each
of the fastening screws f and g as well as 2 sleeves j.
Then screw tight at the top right of the unit using 1 fastening
screw f and sleeve h.
10 Only for the expert
machine can jam due to a warpage in the built-in units. The
door can be adjusted. To do this adjust the hinges at the top
and the bottom.
I. Adjust the depth of the door by turning the screws V.
II. Remove the hinge dampers at the top and bottom of the
hinges. Turn the screws W to adjust the inclination and
III.
11 Insert the cover X
screws i.
12 Replace the drip tray Y and accessories drawer Z and close
the appliance door.
Removal
Undo all screws.
Slightly pull out the appliance.
Remove the power cord from the socket.
Disconnect the appliance from the transformer.
Fully remove the appliance.
Technical specications
Power connection
with transformer type 8001010566
(voltage – frequency)
Power rating 1600 W
19 bar
Length of power cable
(Power socket – transformer)
391 m)
Dimensions
(appliance without transformer)
Weight, empty
(appliance without transformer)
42-44 lb (19-20 kg)
Dimensions (only transformer)
Weight (only transformer) 27.55 lb (12.5 kg)
Type of grinding unit Ceramic