Full HD LCD Monitors UML-262-90 | UML-422-90 en User’s Manual
Full HD LCD Monitors Table of Contents | en 3 Table of Contents 1 Safety 5 1.1 Important safety instructions 5 1.2 Safety precautions 8 1.3 Important notices 1.4 Customer Support and Service 15 2 Unpacking 17 2.1 Parts List 17 3 Monitor Panels 18 3.1 UML-262-90 Front Control Panel 18 3.2 UML-262-90 Bottom Panel 19 3.3 UML-422-90 Front Panel 19 3.4 UML-422-90 Rear Control Panel 20 3.5 UML-422-90 Bottom Panel 21 3.6 Remote Control 22 3.
en | Table of Contents Full HD LCD Monitors 5 Installing the Monitor 27 5.1 Ventilation 27 5.2 Mounting the Monitor 27 5.2.1 Desktop Installation 27 5.2.2 Wall Mount Installation 29 5.3 Connecting the Composite Video Signal to the Monitor 30 5.4 Connecting the Y/C (S-Video) Signal to the Monitor 31 5.5 Connecting Audio to the Monitor 31 5.6 Connecting the PC Signal to the Monitor 32 5.6.1 HDMI Connection 32 5.6.2 DVI Connection 32 5.6.3 VGA Connection 32 5.
Full HD LCD Monitors Safety | en 1 Safety 1.1 Important safety instructions 5 Read, follow, and retain for future reference all of the following safety instructions. Heed all warnings on the unit and in the operating instructions before operating the unit. 1. Cleaning - Unplug the unit from the outlet before cleaning. Follow any instructions provided with the unit. Generally, using a dry cloth for cleaning is sufficient, but a moist flufffree cloth or leather shammy may also be used.
en | Safety Full HD LCD Monitors disconnect the cable system. This will prevent damage to the unit from lightning and power line surges. 7. Controls adjustment - Adjust only those controls specified in the operating instructions. Improper adjustment of other controls may cause damage to the unit. Use of controls or adjustments, or performance of procedures other than those specified, may result in hazardous radiation exposure. 8. Overloading - Do not overload outlets and extension cords.
Full HD LCD Monitors Safety | en 7 13. Damage requiring service - Unplug the unit from the main AC power source and refer servicing to qualified service personnel when any damage to the equipment has occurred, such as: – the power supply cord or plug is damaged; – exposure to moisture, water, and/or inclement weather (rain, snow, etc.
en | Safety 1.2 Full HD LCD Monitors Safety precautions DANGER! High risk: This symbol indicates an imminently hazardous situation such as “Dangerous Voltage” inside the product. If not avoided, this will result in an electrical shock, serious bodily injury, or death. WARNING! Medium risk: Indicates a potentially hazardous situation. If not avoided, this could result in minor or moderate bodily injury. CAUTION! Low risk: Indicates a potentially hazardous situation.
Full HD LCD Monitors Safety | en 9 Coax grounding: – Ground the cable system if connecting an outside cable system to the unit. – Connect outdoor equipment to the unit's inputs only after this unit has had its grounding plug connected to a grounded outlet or its ground terminal is properly connected to a ground source. – Disconnect the unit's input connectors from outdoor equipment before disconnecting the grounding plug or grounding terminal.
en | Safety Full HD LCD Monitors NOTE: Wear required grounded wrist straps and observe proper ESD safety precautions when handling the electrostaticsensitive printed circuit boards. Fuse rating - For security protection of the device, the branch circuit protection must be secured with a maximum fuse rating of 16A. This must be in accordance with NEC800 (CEC Section 60).
Full HD LCD Monitors Safety | en 11 Power lines - Do not locate the display near overhead power lines, power circuits, or electrical lights, nor where it may contact such power lines, circuits, or lights. Rack-mount – Ventilation - Do not place this unit in a built-in installation or rack without proper ventilation or adhering to the manufacturer's instructions. The equipment must not exceed its maximum operating temperature requirements.
en | Safety Full HD LCD Monitors NOTICE! This is a class A product. In a domestic environment this product may cause radio interference, in which case the user may be required to take adequate measures. FCC & ICES Information (U.S.A. and Canadian Models Only) This device complies with part 15 of the FCC Rules.
Full HD LCD Monitors Safety | en 13 Informations FCC et ICES (modèles utilisés aux États-Unis et au Canada uniquement) Ce produit est conforme aux normes FCC partie 15. la mise en service est soumises aux deux conditions suivantes : – cet appareil ne peut pas provoquer d'interférence nuisible et – cet appareil doit pouvoir tolérer toutes les interférences auxquelles il est soumit, y compris les interférences qui pourraient influer sur son bon fonctionnement.
en | Safety Full HD LCD Monitors Disclaimer Underwriter Laboratories Inc. (“UL”) has not tested the performance or reliability of the security or signaling aspects of this product. UL has only tested fire, shock and/or casualty hazards as outlined in UL's Standard(s) for Safety for Closed Circuit Television Equipment, UL 2044. UL Certification does not cover the performance or reliability of the security or signaling aspects of this product.
Full HD LCD Monitors Safety | en 15 NOTE! This manual has been compiled with great care and the information it contains has been thoroughly verified. The text was complete and correct at the time of printing. The ongoing development of the products may mean that the content of the user guide can change without notice. Bosch Security Systems accepts no liability for damage resulting directly or indirectly from faults, incompleteness or discrepancies between the user guide and the product described. 1.
en | Safety Full HD LCD Monitors Asia Region Repair Center Telephone: 65 63522776 Fax: 65 63521776 E-mail: rmahelpdesk@sg.bosch.com Customer Service Telephone: 86 (0) 756 7633117 or 86 (0) 756 7633121 Fax: 86 (0) 756 7631710 E-mail: customer.service@cn.bosch.com Warranty and more information For additional information and warranty queries, please contact your Bosch Security Systems representative or visit our website at www.boschsecurity.com. F.01U.172.600 | 1.0 | 2010.
Full HD LCD Monitors 2 Unpacking | en 17 Unpacking This equipment should be unpacked and handled with care. If an item appears to have been damaged in shipment, notify the shipper immediately. Verify that all the parts listed in the Parts List below are included. If any items are missing, notify your Bosch Security Systems Sales or Customer Service Representative. The original packing carton is the safest container in which to transport the unit and must be used if returning the unit for service.
en | Monitor Panels Full HD LCD Monitors 3 Monitor Panels 3.1 UML-262-90 Front Control Panel Figure 3.1 Ref. Button UML-262-90 Front Panel Description 1 Enter Selects the signal to be displayed. 2 Menu Opens the on-screen display (OSD) menus. 3 Adjusts the value when in the OSD. Scrolls down in the OSD. Activates the Auto Adjust function when in PC mode. 4 Adjusts the value when in the OSD. Scrolls up in the OSD. 5 Decreases the value when in the OSD. Scrolls left in the OSD.
Full HD LCD Monitors 3.2 Monitor Panels | en UML-262-90 Bottom Panel Figure 3.2 Ref. 1 2 3 4 5 6 7 3.3 19 UML-262-90 Bottom View (I/O panel) 24 VDC In HDMI In DVI-2 In DVI-1 In RS-232 In (for firmware updates) VGA in S-Video In Ref. 8 9 10 11 12 13 Video 1 (AV1) In Video 1 (AV1) Out Video 2 (AV2) Out Video 2 (AV2) In Trigger Input Audio In (Left/Right) UML-422-90 Front Panel Figure 3.3 UML-422-90 Front View Ref. Button Description 1 Receives command signals from the remote control.
en | Monitor Panels 3.4 Full HD LCD Monitors UML-422-90 Rear Control Panel Figure 3.4 UML-422-90 Rear View and Control Panel Ref. Button Description 1 Handles Use handles when installing and transporting the monitor. 2 Kensington Lock Use to install a Kensington-type lock to prevent theft. Hole 3 Input Selects the signal to be displayed. 4 Menu Opens the on-screen display (OSD) menus. 5 Adjusts the value when in the OSD. Scrolls down in the OSD.
Full HD LCD Monitors 3.5 21 UML-422-90 Bottom Panel Figure 3.5 Ref. 1 2 3 4 5 6 7 Monitor Panels | en UML-422-90 Bottom View (I/O Panel) 100 — 240 VAC In HDMI In DVI-2 In DVI-1 In RS-232 In (for firmware updates) VGA in S-Video In Bosch Security Systems, Inc. Ref. 8 9 10 11 12 13 User’s Manual Video 1 (AV1) In Video 1 (AV1) Out Video 2 (AV2) Out Video 2 (AV2) In Trigger Input Audio In (Left/Right) F.01U.172.600 | 1.0 | 2010.
en | Monitor Panels 3.6 Full HD LCD Monitors Remote Control 1 19 2 3 4 5 6 7 8 9 10 11 12 13 20 14 15 16 27 21 22 23 24 25 26 17 18 Figure 3.6 F.01U.172.600 | 1.0 | 2010.10 28 Remote Control Detail User’s Manual Bosch Security Systems, Inc.
Full HD LCD Monitors Monitor Panels | en Ref# 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Button POWER Contrast Backlight Color Tone Auto Adj. Info Mute Auto Switching PIP YPbPr PC AV1 AV2 Input Exit (no function) Arrow keys; Description Turns power on and off. Adjusts picture contrast. Adjusts backlight intensity of LCD panel. Adjusts color tone of picture. Auto adjusts the graphics adaptor. Displays the settings of the selected input. Mutes the sound. Selects the Auto Switch function.
en | Monitor Panels 3.7 Full HD LCD Monitors Remote Control Battery Installation 1. Turn the remote over so the buttons face down and push down on the cover and slide it off. 2. Insert two (2) new AAA alkaline batteries, matching the 3. Slide the battery cover back into place. batteries to the (+) and (-) marks inside the battery case. 1 1 2 2 Figure 3.7 Remote Control Battery Placement Note: Replace batteries when required or at least once a year. Dispose of used batteries properly. F.
Full HD LCD Monitors 4 Description | en 25 Description The Bosch High Performance Family of LCD monitors display PAL or NTSC standard color pictures in CCTV systems. The monitors include: two (2) looping Composite Video BNC connector inputs, one (1) RCA audio input (left/right), and one (1) Y/C (S-Video) input using a 4-pin mini-DIN.
en | Description 4.2 Model No. Full HD LCD Monitors Power Rated Voltage Voltage Power at Rated Sync Format UML-262-90 120/230 VAC Range Voltage 100 to 240 V < 70 W NTSC/PAL 50/60 Hz UML-422-90 120/230 VAC 100 to 240 V < 210 W NTSC/PAL 50/60 Hz F.01U.172.600 | 1.0 | 2010.10 User’s Manual Bosch Security Systems, Inc.
Full HD LCD Monitors 5 Installing the Monitor | en 27 Installing the Monitor This chapter outlines the procedures to install the UML-262-90 and the UML-422-90 monitor. A qualified service person should install the monitor and adhere to all local codes. 5.1 Ventilation To prevent overheating, ensure that the ventilation openings on the rear of the monitor are not covered. 5.2 Mounting the Monitor The UML-262-90 and the UML-422-90 are designed for use on a desktop or mounted to a wall or rack. 5.2.
en | Installing the Monitor Full HD LCD Monitors UML-262-90 The viewing angle of the LCD can be adjusted to fit the most comfortable monitoring status. 20 30 30 Figure 5.1 Adjusting the Viewing Angle (UML-262-90) UML-422-90 The desktop stands (item 1, below) can be installed on the rear panel of the monitor for a desktop application. Figure 5.2 F.01U.172.600 | 1.0 | 2010.10 Installing Desktop Stands (UML-422-90) User’s Manual Bosch Security Systems, Inc.
Full HD LCD Monitors 5.2.2 Installing the Monitor | en 29 Wall Mount Installation This monitor can be wall-mounted using the mounting holes and a suitable wall mount or swivel/tilt mount. Refer to the figures below for the dimensions of the mounting holes on a UML-262-90 and a UML-422-90 monitor. CAUTION! Use a UL-listed mounting system that is rated to support the following weight of the specific monitor (without stand): – UML-262-90: 10 kg (22.05 lb) – UML-422-90: 23.85 kg (52.
en | Installing the Monitor Full HD LCD Monitors 400 mm 200 mm Figure 5.4 5.3 UML-422-90 Mounting Hole Dimensions Connecting the Composite Video Signal to the Monitor There are two (2) BNC connectors located on the rear side panel of the monitor for composite video inputs and two (2) BNC connectors for composite video outputs (see Figure 3.2 and Figure 3.5). Note: All video inputs are passive loop-through.
Full HD LCD Monitors 5.4 Installing the Monitor | en 31 Connecting the Y/C (S-Video) Signal to the Monitor There is one (1) mini-DIN type connector for the S-Video (Y/C) input (see Figure 3.2 and Figure 3.5) on the rear side panel. Note: Both Y and C inputs are terminated with 75 Ohm. 5.5 Figure 5.5 Y/C Connector pin-out Number 1 2 3 4 Input Ground Ground Y-signal C-signal Connecting Audio to the Monitor There is one (1) set of stereo audio connectors for audio input, located on the rear panel.
en | Installing the Monitor 5.6 Full HD LCD Monitors Connecting the PC Signal to the Monitor There are three ways to connect the PC signal to the monitor: HDMI, DVI, and VGA. 5.6.1 HDMI Connection Connect an HDMI cable (user-supplied) to the HDMI input on the bottom panel of the monitor. Figure 5.6 5.6.2 HDMI Input DVI Connection Connect a DVI-D cable (supplied) to one of the DVI-D inputs on the bottom panel of the monitor. Figure 5.7 5.6.
Full HD LCD Monitors 5.7 Installing the Monitor | en 33 Connecting an Alarm Trigger The monitor contains an alarm Trigger Input and a Trigger cable. These components allow you to connect an alarm relay from a device, such as a camera or a door. Connect the two flying leads from the Trigger cable into the relay out ports of the device. Then, route the other end of the cable to the Trigger Input connector on the back panel of the monitor.
en | Installing the Monitor 2. 3. Full HD LCD Monitors Configure the following settings for the Dinion camera: – VMD: OSD – Area: 1 – Active: On Connect one flying lead to relay output three (3), on the back of the Dinion camera, and connect the other to relay output four (4). 4. Connect the other end of the Trigger cable to the Trigger Input connector on the bottom panel of the monitor. 5. Plug the monitor into a power socket; then press the Power button. 6.
Full HD LCD Monitors 5.8 Installing the Monitor | en 35 Single / Multiple Monitor Configuration Figure 5.10 Ref 1 2 Single Monitor Configuration Description Ref Video Camera 3 AV1 In 4 Bosch Security Systems, Inc. Description AV1 Out DVR User’s Manual F.01U.172.600 | 1.0 | 2010.
en | Installing the Monitor Full HD LCD Monitors Figure 5.11 Multiple Monitor Configuration Ref 1 2 3 Description Video Camera AV1 In AV1 Out F.01U.172.600 | 1.0 | 2010.10 User’s Manual Bosch Security Systems, Inc.
Full HD LCD Monitors Navigating the Monitor | en 6 Navigating the Monitor 6.1 Navigating the Front Panel 37 Use the front panel to make any necessary OSD adjustments to the UML-262-90 and the UML-422-90. See the figure below for an explanation of the front panel. Figure 6.1 UML-262-90 Control Panel Buttons Figure 6.2 UML-422-90 Control Panel Buttons Ref. Button Description 1 Enter/Input Selects the signal to be displayed. 2 Menu Enters the on-screen display (OSD) menus.
en | Navigating the Monitor 6.2 Full HD LCD Monitors Navigating the Monitor On-screen Display (OSD) The UML-262-90 and the UML-422-90 have two (2) modes: Video and PC. The LCD is programmed through the on-screen display (OSD) menus and submenus where an operator can select operating parameters. To access the OSD menus, press the Menu button on the control panel or on the remote control. Use the control panel of the monitor or the remote control to make any necessary adjustments to the OSD.
Full HD LCD Monitors 6.3 Navigating the Monitor | en 39 On-screen Display Menus There are four (4) on-screen menus that allow you to customize your settings. Press the Menu button to access the OSD menu. Icon Menu Custom Function Adjusts the Brightness, Contrast, Color, Tint, Sharpness, and the Backlight level for video performance. (The menu options differ between the Video and PC modes.) Picture/Sound Adjusts the Picture Mode, Color Tone, Audio Source, Mute, Volume, PC, and the Size settings.
en | Navigating the Monitor 6.4 Full HD LCD Monitors Custom Menu To access the Custom menu, press the Menu button on the control panel of the monitor. Next, press the Up or Down Arrow button to select the Custom menu. Press the Right Arrow button to enter the menu, and then press the Up and Down Arrow buttons to select. When finished, press the Menu button to save any changes, then press the Menu button again to exit the OSD.
Full HD LCD Monitors Navigating the Monitor | en Submenu Definition Brightness Adjusts the brightness level for video performance (range 0-100). Contrast Adjusts the contrast level for video performance (range 0-100). Color Adjusts the overall color intensity of the screen (range 0-100). Tint Adjusts the tint of the picture (range 0-100). NTSC only. Sharpness Adjusts the sharpness level for video performance (range 0-10). Backlight Adjusts LCD backlight intensity of the screen (range 0-100).
en | Navigating the Monitor Full HD LCD Monitors Picture/Sound Picture Mode Color Tone Audio Source Mute Volume PC Size Move Enter Middle 6500°K Audio Off 50 Full Enter Exit Table 6.4 Picture/Sound Menu (PC Mode) Submenu Definition Picture Mode Selects the automatic picture control mode. Choices are: (Video Mode) Custom: User selected values of the Custom menu are applied. Dynamic: Automatically adjusts the Brightness, Contrast, and Sharpness, maximizing the video quality in the picture.
Full HD LCD Monitors Size Navigating the Monitor | en 43 Selects the Aspect Ratio Control mode. Choices are: Full, Normal, Zoom1, and Zoom2. Overscan Adjusts the overscan settings when displaying video (non-PC) signals: (Vide Mode) H-Phase: Adjusts the horizontal phase of the overscanned picture (range 1-9). V-Phase: Adjusts the vertical phase of the overscanned picture (range 1-9). H-Overscan: Adjusts the horizontal overscan size (range 1-9).
en | Navigating the Monitor 6.6 Full HD LCD Monitors PIP Menu To access the PIP menu, press the Menu button on the control panel of the monitor, then press the Up and Down Arrow buttons to select the PIP icon. Press the Right Arrow button to enter the menu, and then press the Up and Down Arrow buttons to select a submenu. When finished, press the Menu button to save any changes, then press the Menu button again to exit the OSD.
Full HD LCD Monitors Navigating the Monitor | en 45 PIP Availability The table below summarizes the availability of the input source combinations for the PIP feature. (A “+” indicates an allowed combination, a blank cell indicates the combination is not allowed). AV1 AV1 AV2 S-Video Sub PC Picture DVI1 DVI2 HDMI + + + + + + AV2 + + + + + + Main Picture Input Source S-Video PC DVI1 DVI2 + + + + + + + + + + + + + + + HDMI + + + Table 6.6 PIP Availability 6.
en | Navigating the Monitor Full HD LCD Monitors Setup Reset Language OSD Tone Blue Screen Key Lock Trigger Auto Switch Display Wall Image Retention Firmware Version Move Enter English On On Off Enter On X.X Exit Table 6.7 Setup Menu Submenu Definition Reset Restores default settings. Language Adjusts the language of the OSD. Choices are: English, French, Spanish, Dutch, German, Italian, Portuguese, Russian, Polish, Simplified Chinese, and Japanese.
Full HD LCD Monitors Auto Switch Navigating the Monitor | en 47 Enables or disables the auto switch function that allows the monitor to automatically switch to and display an available input signal. Display Wall If multiple UML-422-90 monitors are tiled to form a display wall, use this function to configure the display wall settings: X. Index: Selects the horizontal position of the monitor in the display wall matrix. Matrix: Selects the matrix configuration of the display wall. Y.
en | Power Management 7 Full HD LCD Monitors Power Management These monitors feature a power management system to “power down” upon receipt of the display power management signaling (DPMS) from a DPMS video card. The DPMS-compliant video card performs this signaling by not sending a horizontal, vertical, or a sync signal. The monitor enters an appropriate mode through identifying each of the three (3) modes of the signaling system. 7.1 Power Consumption Mode ON ACTIVE OFF 7.
Full HD LCD Monitors 8 Troubleshooting | en 49 Troubleshooting Problem Solution No image displayed on screen – Check that the power cord of the monitor is securely connected into the wall outlet or grounded extension cable or strip. – Power switch should be in the ON position and the LED lit. – Check that the Brightness and/or Contrast adjustments of the display have not been turned down to minimum levels.
9 en | Maintenance Full HD LCD Monitors Maintenance To clean the LCD panel, wipe off water droplets or oil immediately with absorbent cotton or a soft lint-free cloth. Staining and discoloration may occur if a liquid is left on the panel for long periods. If the surface (polarizer) of the LCD panel is dirty or stained, use absorbent cotton or a soft lint-free cloth to remove the residue as follows: 1. Turn off the display and disconnect it from the power supply. 2.
Full HD LCD Monitors 10 Technical Specifications | en 51 Technical Specifications Model UML-262-90 UML-422-90 LCD Type 26.02 in. Digital LCD 42.02 in. Digital LCD Backlight Type CCFL CCFL Pixel Pitch (H x V) 0.3 x 0.3 mm 0.4845 x 0.
en | Technical Specifications F.01U.172.600 | 1.0 | 2010.10 Full HD LCD Monitors User’s Manual Bosch Security Systems, Inc.
Bosch Security Systems, Inc. www.boschsecurity.com © Bosch Security Systems, Inc.
