VideoJet 8008 / VideoJet 8004
Copyright This manual is copyright protected by Bosch Security Systems. All rights reserved. No part of this document may be reproduced or transmitted for any purpose, by whatever method and by whatever means, electronically or mechanically, without the express written permission of Bosch Security Systems. Issue: July 2006 (Software version 1.5) © Copyright 2006 Bosch Security Systems Note This manual has been prepared with all due care and all information contained in it has been thoroughly checked.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual Content EN | 3 0 Chapter 1 Preface Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Intended use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 EU Directives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Rating plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EN | 4 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Recording video sequences . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 Running recording program . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 The MEDIA-REPLAY page . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 Installing MPEG viewer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual Preface EN | 5 1 This manual is intended for persons responsible for the installation and operation of the VideoJet 8008 or VideoJet 8004. International, national and any regional electrical engineering regulations must be followed at all times. Relevant knowledge of network technology is required. The manual describes the installation and operation of the unit.
EN | 6 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Intended use The VideoJet 8008 and VideoJet 8004 network video servers transmit video and control signals over data networks (Ethernet LAN, Internet). The integrated hard drive allows you to use the device as a DVR. Audio signals can also be transmitted with the audio versions of the units. The units are designed for use in CCTV systems. Various functions can be triggered automatically by incorporating external alarm sensors.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual Safety information EN | 7 2 Electric shock hazard ❚ Never attempt to connect the unit to any power network other than the type for which it is intended. ❚ Never open the housing. ❚ If a fault occurs, disconnect the unit from the power supply and from all other units. ❚ Install the unit only in dry, weather-protected locations.
EN | 8 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Installation and operation ❚ The relevant electrical engineering regulations and guidelines must be complied with at all times during installation. ❚ Relevant knowledge of network technology is required to install the unit. ❚ Before installing or operating the unit, make sure you have read and understood the documentation for the other equipment connected to it, such as cameras.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual Product description EN | 9 3 Components supplied ❚ VideoJet 8008 or VideoJet 8004 network video server (basic version or audio version) ❚ Power supply cable ❚ Configuration cable ❚ Mounting kit for installation in 19-inch racks ❚ Quick Installation Guide ❚ Product CD with the following content: – Quick Installation Guide – Manual – System Requirements document – MPEG ActiveX control – MPEG viewer – DirectX control – Microsoft Internet Exp
EN | 10 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Configuration requirements ❚ Computer with Windows 2000/XP operating system, access to a network and Microsoft Internet Explorer (version 6.0 or higher) or ❚ Computer with Windows 2000/XP operating system, access to a network and receiver software, such as VIDOS Note Also note the information in the System Requirements document on the product CD supplied.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 11 Overview of functions Network video server VideoJet 8008 and VideoJet 8004 are network video servers for eight independent video channels. They are primarily designed for encoding video and control data for transmission over an IP network. With the audio versions, audio signals can also be transmitted to and from compatible units.
EN | 12 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Multicast In suitably configured networks, the multicast function enables simultaneous real-time video transmission to multiple receivers. The UDP and IGMP V2 protocols must be implemented on the network for this function. DVR The integrated hard drive means that VideoJet 8008 and VideoJet 8004 can be used as digital video recorders for local long-term recording.
EN | 13 VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual Summary VideoJet 8008 and VideoJet 8004 offer the following main functions: ❚ Video and data transmission over IP data networks ❚ Dual Streaming function for every encoder to allow simultaneous encoding based on two individually definable profiles (only VideoJet 8008) ❚ Multicast function for simultaneous image transmission to multiple receivers ❚ Eight independent analog BNC composite video inputs (PAL/NTSC) ❚ Video encoding to int
EN | 14 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Connections on the rear panel 1 Eight audio ports (Mono): Audio 1 to Audio 8 (audio versions only) 3.5 mm stereo sockets for connecting audio cables 2 Additional terminal block (audio versions only) Relay outputs, serial interface, audio port for microphone and loudspeaker (speaking level) 3 Audio Out audio output (audio versions only) 3.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 15 Front panel 10 Power LED lights up green when ready for operation 11 IR diode infrared receiver (for future function extensions) 12 HDD LED flashes red during data transmission to and from the hard drive 13 Fail LED flashes red during hardware error (defective fans) 14 Display for displaying operating parameters 15 Menu/Exit key for activating and deactivating the configuration menu 16 Set key for saving changes to the operating pa
EN | 16 Product description Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Bosch Security Systems | 2006-07 | V1.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual Installation EN | 17 4 VideoJet 8008 and VideoJet 8004 are designed as desktop units and intended for installation in a switch cabinet. Mounting in a 19-inch rack using the mounting kit supplied is a quick and easy operation. For desktop operation, four self-adhesive, non-slip rubber feet are included, which you can stick to the bottom of the unit. Caution The unit is designed for indoor operation.
EN | 18 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Installing in a switch cabinet VideoJet 8008 and VideoJet 8004 are set up for installation in a 19-inch rack. The necessary mounting kit is already supplied. Caution When installing in a switch cabinet, ensure that there is sufficient ventilation for each unit: There must be at least 5 cm (1.97 in.) of free space to the left and right of the unit and at least 10 cm (3.94 in.) at the rear.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 19 Installation overview Bosch Security Systems | 2006-07 | V1.
EN | 20 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Connections Cameras You can connect a maximum of eight standard video sources (such as CCTV cameras). Any cameras and other video sources that produce a standard PAL or NTSC signal are suitable. Note On the VideoJet 8008, the maximum resolution at the complete image rate for each camera input is Full D1/4CIF.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 21 Data interface The bidirectional data interface is used to control connected units, such as a dome camera with motorized lens. The range of controllable equipment is expanding constantly. The manufacturers of the relevant equipment provide specific information on installation and control. The RS232/485 connection supports the RS232, RS422 and RS485 transmission standards. The serial interface is designed as a RJ45 socket.
EN | 22 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Audio connections (audio versions only) The audio versions of VideoJet 8008 and VideoJet 8004 have several audio ports for audio line signals as well as a microphone input and a loudspeaker output. The audio signals are transmitted two-way and in sync with the video signals. As a result, you can connect a speaker or door intercom system at the destination point, for example.
EN | 23 VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual The stereo socket plugs must be connected as follows: Contact Audio 1 to Audio 8 Audio Out Tip Line Out Left channel Middle ring Line In Right channel Lower ring Ground Ground – Connect the desired audio sources with line level to the Audio 1 to Audio 8 sockets with a 3.5 mm stereo plug. – If necessary, connect two loudspeakers to the Audio Out socket.
EN | 24 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Power on/Power off Power supply The VideoJet 8008 and VideoJet 8004 are supplied with a power supply cable and rubber connector. The units do not have a power switch. After you have connected the unit to the power supply and the unit has booted, it is ready for use. Caution Where necessary, use suitable equipment to ensure that the power supply is free from interference such as voltage surges, spikes or voltage drops.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 25 Setup using a terminal program Data terminal You can connect a data terminal to the unit for setup and local control. The data terminal consists of a computer with a terminal program. Use the configuration cable supplied to establish the connection. HyperTerminal, a communications accessory included with Microsoft Windows, can be used as the terminal program.
EN | 26 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Command inputs After the connection has been established, you must log onto the unit to access the main menu. Other submenus and functions can be accessed using the on-screen commands. – If necessary, turn off the local echo so that entered values are not repeated on the display. – Enter one command at a time.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 27 – Enter i again. The terminal program displays the current IP address and prompts you to enter a new IP address. – Enter the desired IP address and press [ENTER]. The terminal program displays the new IP address. – If necessary, enter command s and a new subnet mask. Note You must restart to activate the new IP address, a new subnet mask or a gateway address.
EN | 28 Installation Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Bosch Security Systems | 2006-07 | V1.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual Configuration using a Web browser EN | 29 5 Connecting The integrated HTTP server provides you with the option to configure the unit over the network with a Web browser. This option is significantly more comprehensive and convenient than configuration using a terminal program and also offers you the option of displaying live video images.
EN | 30 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 – Insert the CD into the computer's CD-ROM drive. If the CD does not start automatically, open the root directory of the CD in Windows Explorer and double click MPEGAx.exe. – Follow the on-screen instructions. Establishing the connection To operate the unit in your network, it must have a valid IP address for your network. The following default address is preset at the factory: 192.168.0.1 – Start the Web browser.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 31 Note The screen display can differ from that shown above, depending on the unit variants that you use. If you do not connect, the device may have reached its maximum number of connections. The maximum number of connections depends on the unit and network configuration.
EN | 32 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Configuration menu The configuration menu is recommended for expert users or system administrators. You can access all unit parameters in this mode. Settings that affect the fundamental functioning of the unit (such as firmware updates) can only be made using the configuration menu. Starting configuration Click the SETTINGS link in the upper section of the LIVEPAGE window.
EN | 33 VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual Unit overview The unit overview is a graphic presentation of the various areas of the configuration. The individual configuration parameters are arranged in groups and displayed in separate windows. You can access the individual areas directly. – Click one of the graphic symbols. A new window will open.
EN | 34 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Encoder settings For encoding the video signal, you can select a profile for each camera, and for Dual Streaming compatible units you can select two profiles each. You can identify the Dual Streaming compatible units from the additional MPEG-4 Stream 2 tab. Selecting a profile You can configure the MPEG-4 data transmission in accordance with the operating environment (for example network structure, bandwidth, data load).
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 35 ❚ Profile 1: Low bandwidth (CIF) High quality for low bandwidth connections, resolution 352 × 288/240 pixels ❚ Profile 2: Low delay (1/2 D1) High quality with low delay, resolution 352 × 576/480 pixels ❚ Profile 3: High resolution (D1/4CIF) High resolution for high bandwidth connections, resolution 704 × 576/480 pixels ❚ Profile 4: DSL For DSL connections at 500 kBit/s, resolution 352 × 288/240 pixels ❚ Profile 5: ISDN (2B) For ISDN
EN | 36 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Note When local recording is running, the profile set as the Recording profile for the relevant video input is active (see page 45). Changing profiles You can change individual parameter values within a profile and you can also change the name. You can switch between the profiles by clicking the appropriate tab. Caution The profiles are rather complex.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 37 Profile name: You can enter a new name for the profile here. The name is then displayed in the MPEG-4 encoder field in the list of selectable profiles. Target data rate: You can limit the data rate for the unit to optimize utilization of the bandwidth in your network. The target data rate should be set according to the desired picture quality for typical scenes with no excessive motion.
EN | 38 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 I-frame distance: This parameter allows you to set the intervals in which the I-frames will be coded. 0 means auto mode, whereby the video server inserts I-frames as necessary. An entry of 1 indicates that I-frames are continuously generated. An entry of 2 indicates that only every second image is an I-frame, and 3 only every third image etc.; the frames in between are coded as P-frames.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 39 Recording parameters Here, you can set all parameters for recording on the local hard drive. Recording can be performed continuously or only in the case of an alarm. Partition: Select the partition in which you want to record. Recording is performed for every video input in a separate partition. Activating a partition for recording After configuration, you can activate the partition for recording by clicking the Start button.
EN | 40 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 After starting, the Time recording, Alarm recording and Properties pages for the activated partition are displayed in gray and the configuration cannot be modified. The graphic in the lower section of the pages indicates this partition's recording activity. You will see an animated graphic while recording is taking place. You can terminate recording at any time and deactivate one, multiple or all partitions.
EN | 41 VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual Used filetracks on partition: Within a partition, up to 128 filetracks are created automatically. Each new recording has its own track. In Linear mode (see page 45), no more new recordings are made when the 128 tracks are written; old recordings must first be deleted. In Ring mode, the 129th recording is written in the first track again etc., so that the oldest recording is overwritten with the most recent recording.
EN | 42 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Alarm recording Here, you can specify the times during which continuous recording to the hard drives should take place in the event of an alarm. As with time recording, there are separate selection fields for each partition and thus for each camera input. You can select up to 16 separate periods for each day of the week. Alarm recording occurs only during the highlighted time intervals.
EN | 43 VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual This segment in the partition functions in a similar manner to a ring buffer and is overwritten until an alarm is actually triggered. Recording occurs on the segment only for the duration of the preset post-alarm time and a new segment subsequently used in the same manner. This ensures that the alarm recorded is always secured for its entire duration and the space required to save each alarm recording is easy to calculate.
EN | 44 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Properties You can view the current properties for the partition selected in each case directly in the recording scheduler and modify them if necessary. You can also activate the alarms that should trigger recording. Similarly, you can also select the profile for recording. Configuration using a Web browser Bosch Security Systems | 2006-07 | V1.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 45 Caution All modifications result in the reorganization of the partition and the loss of all sequences on this partition. Consequently, you should back up all important sequences on the computer's hard drive. Partition name: You can enter a new name for the partition. Video input: The number of the associated video input and the stream used for the recording are displayed here.
EN | 46 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Alarm recording at: You can select the alarm sensor that is to trigger a recording. You can also use the motion and video alarm for a camera to trigger the alarm recording by another camera. Note The alarm sensor must be active to be able to trigger the recording. The alarm inputs and video loss alarms are activated on the Alarm settings page (see page 51).
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 47 System settings Here you can set or select various basic data for the unit. Unit identification Unit name: You can give the unit a name to make it easier to identify. The name simplifies the management of multiple units in larger systems, for example using the VIDOS program.
EN | 48 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Password A unit is generally protected by a password to prevent unauthorized access to the unit. You can use different authorization levels to limit access. Note Proper password protection is only guaranteed when all higher authorization levels are also protected with a password. If a live password is assigned, for example, a service and a user password must also be set.
EN | 49 VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual Confirm password: Enter the new password a second time to eliminate typing mistakes. Note The new password is only saved when you click the Set button. You should therefore click the Set button immediately after entering and confirming the password, even if you also wish to subsequently assign a password to another user name. Language Website language: Select the language for the user interface here.
EN | 50 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Unit date and Unit time: If there are multiple devices operating in your system or network, it is important to synchronize their internal clocks. For example, it is only possible to identify and correctly evaluate simultaneous recordings when all units are operating on the same time. – Enter the current date.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 51 Alarm settings In this option you can make your settings for the alarm sources and alarm connections. Alarm sources You can configure the possible alarm triggers for the unit (for example, the alarm inputs). Alarm input 1 to Alarm input 10: Select the On option to activate the alarm by the corresponding external alarm sensor. Otherwise, select Off. Select Active high if the alarm is to be triggered by closing the contact.
EN | 52 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Name: You can enter a name for each alarm input, which is then displayed below the icon for the alarm input on the LIVEPAGE if configured correctly (see Livepage configuration, page 112). Video loss alarm: Activate the checkbox if you want an interruption of the video signal to trigger an alarm. A selected video input is indicated by a check mark.
EN | 53 VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual Alarm connections You can select how the unit responds to an alarm. In the event of an alarm, the unit can automatically connect to a pre-defined IP address. You can enter up to ten IP addresses to which the unit will connect in sequence in the event of an alarm, until a connection is made. You can also select which camera image should automatically be shown first on the receiver in the event of an alarm.
EN | 54 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Auto-connect: Select the On option to automatically re-establish a connection to one of the previously specified IP addresses after each restart, after a connection breakdown or after a network failure. Note Dual Streaming compatible units only: Stream 2 is always transferred for alarm connections. Bear this fact in mind when assigning the profile (see page 34).
EN | 55 VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual Network settings Here you can specify network addresses and configure multiple connections. Network The settings in this screen are used to integrate the unit into an existing network. Caution Changes to the IP address, subnet mask or gateway address are transferred to the unit by clicking Set. However, they only take effect after the unit is restarted. – Click Set after entering a new IP address.
EN | 56 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Gateway IP address: If you want the unit to establish a connection to a remote location in a different subnet, enter the IP address of the gateway here. Otherwise leave the box blank (0.0.0.0). Ethernet link type: If the unit is connected to the network via a switch, both must have the same default for the type of network connection. If necessary, ask your network administrator what value the switch is set to.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 57 Multicasting In addition to a 1:1 connection between an encoder and a single receiver (unicast), the unit can enable multiple receivers to receive the video signal from an encoder simultaneously.
EN | 58 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 The multicast address can be the same for multiple streams. However, it will be necessary to use a different port in each case so that multiple data streams are not sent simultaneously using the same port and multicast address. Note The settings must be made individually for each video input and, on Dual Streaming compatible units, for each stream.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 59 Note Audio signals are only transmitted if the audio function is activated on the Audio Stream configuration page (see page 78). Multicast port 1: (audio versions only) Enter the port address of the separate audio stream here. Bosch Security Systems | 2006-07 | V1.
EN | 60 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 COM settings You can configure the parameters of the RS232/485 serial interface to meet your requirements. On audio versions, you can also configure the parameters of the second RS232 serial interface. COM1 Note If the unit is working in multicast mode (see page 57 onward), the first remote location to establish a video connection to the unit is also assigned the transparent data connection.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 61 Camera ID: If necessary, enter the ID of the peripheral you wish to control (for example a dome camera or pan/tilt head). Note If you are using a Bosch AutoDome, remember that the value of the Camera ID must always be selected one less than the Bosch camera number (for example: Bosch camera number: 1, Camera ID: 0). Baud rate: Select the value for the transmission rate in bit/s.
EN | 62 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 COM2 (audio versions only) Serial port function: Select the desired function from the list. If you wish to use the additional RS232 serial interface (9-pin sub-D socket) to transmit transparent data, select Transparent. Select Terminal if you wish to operate the unit from a terminal. Baud rate: Select the value for the transmission rate in bit/s. Data bits: The number of data bits per character cannot be changed.
EN | 63 VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual Configuration menu The configuration menu allows you to configure all parameters of the unit. You can view the current settings by opening one of the configuration screens. You can change the settings by entering new values or by selecting a predefined value from a list field. Navigation You see the configuration menu as well as the unit overview when you click the SETTINGS link on the LIVEPAGE.
EN | 64 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Making changes Each configuration screen shows the current settings. You can change the settings by entering new values or by selecting a predefined value from a list field. – After each change, click Set to save the change. Caution Save each change with the associated Set button. Clicking the Set button saves the settings only in the current field. Changes in any other fields are ignored.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 65 Password A unit is generally protected by a password to prevent unauthorized access to the unit. You can use different authorization levels to limit access. Note Proper password protection is only guaranteed when all higher authorization levels are also protected with a password. If a live password is assigned, for example, a service and a user password must also be set.
EN | 66 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Confirm password: Enter the new password a second time to eliminate typing mistakes. Note The new password is only saved when you click the Set button. You should therefore click the Set button immediately after entering and confirming the password, even if you also wish to subsequently assign a password to another user name. Language You can select the language of the user interface to make the unit easier to use.
EN | 67 VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual Unit time: Enter the current time or click the Synchr. PC button to copy your computer's system time to the unit. Time server The unit can receive the time signal of a time server via the Time Server Protocol (RFC 868) and set the internal clock accordingly. The unit polls the time signal automatically every ten minutes. Time zone: Select the time zone in which your system is located.
EN | 68 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Camera names The camera name makes it easier to identify the remote camera location, in the event of an alarm for example. It will be displayed in the video screen if configured to do so (see page 69). The camera name is also used by VIDOS, the program for managing video surveillance systems, and makes it easier to identify the camera there. Camera 1 to Camera 8: Enter a unique and clear description as the camera name.
EN | 69 VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual Display stamping Various overlays or “stamps” in the video image provide important supplementary information. These overlays can be enabled individually and are arranged on the image in a clear manner. Note The settings on this page apply to all camera inputs. Camera name stamping: This field sets the position of the camera name overlay.
EN | 70 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Displayed alarm message: Enter the message to be displayed for an alarm. The maximum text length is 31 characters. Video watermarking: Choose On if you wish the transmitted video images to be “watermarked”. After activation, all images are marked with a small green rectangle. A red rectangle indicates that the sequence (live or saved) has been manipulated. Configuration using a Web browser Bosch Security Systems | 2006-07 | V1.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 71 Picture settings You can set the video image of each camera to suit your requirements. The current video image is displayed in the small window next to the slide controls as confirmation. Your changes are effective immediately. – Click a tab to select the corresponding camera. – Set the slide bar to the desired position. – Click Default to reset all settings to their default value. Contrast (0...
EN | 72 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 MPEG-4 encoder For encoding the video signal, you can select a profile for each camera, and for Dual Streaming compatible units you can select two profiles each. You can identify the Dual Streaming compatible units from the additional MPEG-4 Stream 2 tab. Selecting a profile You can configure the MPEG-4 data transmission in accordance with the operating environment (for example network structure, bandwidth, data load).
EN | 73 VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual ❚ Profile 3: High resolution (D1/4CIF) High resolution for high bandwidth connections, resolution 704 × 576/480 pixels ❚ Profile 4: DSL For DSL connections at 500 kBit/s, resolution 352 × 288/240 pixels ❚ Profile 5: ISDN (2B) For ISDN connections via two B channels, resolution 352 × 288/240 pixels ❚ Profile 6: ISDN (1B) For ISDN connections via one B channel, resolution 352 × 288/240 pixels ❚ Profile 7: Modem For analog modem connec
EN | 74 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Changing profiles You can change individual parameter values within a profile and you can also change the name. You can switch between the profiles by clicking the appropriate tab. Caution The profiles are rather complex. They include a large number of parameters that interact with one another, so it is generally best to use the default profiles.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 75 Target data rate: You can limit the data rate for the unit to optimize utilization of the bandwidth in your network. The target data rate should be set according to the desired picture quality for typical scenes with no excessive motion. For complex images or frequent changes of image content due to frequent movements, this limit can be temporarily exceeded up to the value you enter in the Max. data rate field. Max.
EN | 76 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Encoding interval: The figure selected here determines the interval at which images are encoded and transmitted. For example, entering 4 means that only every fourth image is encoded, the following three are skipped - this can be particularly advantageous with low bandwidths. Video resolution: Here you can select the desired resolution for the MPEG-4 video image.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 77 Video input Note The numbering follows the labeling of the video inputs on the actual unit. Source type input 1 to Source type input 8: To allow video recorders to be connected as a video source, you can change the characteristic of the video source from the preset value of Camera to VCR.
EN | 78 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Audio stream (audio versions only) The audio version of the unit has several audio ports for audio line signals as well as a microphone input and loudspeaker output. The audio signals are transmitted two-way and in sync with the video signals. When transmitting audio signals, a maximum of one input and one output current is possible at the same time. However, several audio outputs can be connected with the same audio stream.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 79 Audio output channel: Note The numbering follows the labeling of the audio sockets on the unit. You can connect outputs Audio 8 (Output 8), AO (Intercom) and Audio Out (Stereo out) to the same audio stream simultaneously. – Select the desired audio output from the list. – Select audio output 8 from the list and check the Intercom box to select the station output AO (terminal connector).
EN | 80 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 JPEG posting You can save individual JPEG images on an FTP server at certain intervals. You can then retrieve these images at a later date to reconstruct alarm events if required.
EN | 81 VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual JPEG posting interval: Enter the interval in seconds at which the images will be sent to an FTP server. Enter zero if you do not want any images to be sent. FTP server IP address: Enter the IP address of the FTP server on which you wish to save the JPEG images. FTP login name: Enter your login name for the FTP server. FTP password: Enter the password that gives you access to the FTP server.
EN | 82 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Partitioning Eight partitions can be set up for the unit's hard drive, in a similar manner to the partitioning often found on computer hard drives. Parameters such as size, quality and type of video recording or compression standard used can be specified for each partition. Modifying these parameters leads to reorganization, during which stored data is lost.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 83 Creating a partition Caution Modifications to the size or number of partitions lead to the entire hard drive being reorganized and the loss of all sequences stored on the drive. Consequently, you should check the recordings before any modification to the parameters mentioned and back up important sequences on the computer's hard drive.
EN | 84 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 – Click the Create partition button to start the wizard for creating partitions. The first window of the wizard opens. – You should always first read the information text in the upper section of the window. – Click in the text fields to enter values or use the other controls that are available, such as buttons, checkboxes or list fields. – Click the Next>> button at the bottom of the window to continue with the next step.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 85 Caution All modifications to settings are only effective if you complete the configuration in the last window of the wizard by clicking Finish. – Switch to the last window of the wizard if necessary. – Click Finish to complete the configuration. All settings are now transferred to the unit and subsequently become effective. Editing a partition You can modify the configuration of a partition at any time.
EN | 86 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Consequently, you should back up all important sequences on the computer's hard drive before modifying the partition. You can perform the required modifications in the Partition properties window. – In the list, click the partition that you want to modify in order to select this partition. – Click the Edit partition button. A new window with the entries for the selected partition is opened. – Make the desired changes.
EN | 87 VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual Recording scheduler Here, you can set all parameters for recording on the local hard drive. Recording can be performed continuously or only in the case of an alarm. Partition: Select the partition in which you want to record. Recording is performed for every video input in a separate partition. Activating a partition for recording After configuration, you can activate the partition for recording by clicking the Start button.
EN | 88 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 – Click the Start button to activate the currently selected partition for recording. – Click the Start all button to activate all the partitions set up for the recording. – Click the Stop button to deactivate the currently selected partition for recording. Recordings that are currently running will be interrupted and the configuration can be modified.
EN | 89 VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual Used filetracks on partition: Within a partition, up to 128 filetracks are created automatically. Each new recording has its own track. In Linear mode (see page 93), no more new recordings are made when the 128 tracks are written; old recordings must first be deleted. In Ring mode, the 129th recording is written in the first track again etc., so that the oldest recording is overwritten with the most recent recording.
EN | 90 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Alarm recording Here, you can specify the times during which continuous recording to the hard drives should take place in the event of an alarm. As with time recording, there are separate selection fields for each partition and thus for each camera input. You can select up to 16 separate periods for each day of the week. Alarm recording occurs only during the highlighted time intervals.
EN | 91 VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual This segment in the partition functions in a similar manner to a ring buffer and is overwritten until an alarm is actually triggered. Recording occurs on the segment only for the duration of the preset post-alarm time and a new segment subsequently used in the same manner. This ensures that the alarm recorded is always secured for its entire duration and the space required to save each alarm recording is easy to calculate.
EN | 92 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Properties You can view the current properties for the partition selected in each case directly in the recording scheduler and modify them if necessary. You can also activate the alarms that should trigger recording. Similarly, you can also select the profile for recording. Caution All modifications result in the reorganization of the partition and the loss of all sequences on this partition.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 93 Video input: The number of the associated video input and the stream used for the recording are displayed here. The numbering is the same as the labeling of the video inputs on the rear panel of the unit. Note On Dual Streaming compatible units, stream 2 is always used for the recording. Type of recording: Select the required recording type. In the case of Ring mode the recording proceeds continuously.
EN | 94 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 – Check the box for the alarm sensor that is to trigger a recording. The selected check boxes are marked with a tick. Note The numbers of the alarm input check boxes correspond to the labeling of the alarm inputs on the rear panel of the unit. The motion and video loss alarm numbers correspond to the labeling of the video inputs. Partition total size: This displays how much storage space the partition occupies on the hard drive.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 95 Alarm sources You can configure the possible alarm triggers for the unit (for example, the alarm inputs). Alarm input 1 to Alarm input 10: Select the On option to activate the alarm by the corresponding external alarm sensor. Otherwise, select Off. Select Active high if the alarm is to be triggered by closing the contact. Select Active low if the alarm is to be triggered by opening the contact.
EN | 96 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Note The numbers of the check boxes correspond to the labeling of the video inputs on the rear panel of the unit. 1. SNMP host address / 2. SNMP host address: The unit supports the SNMP (Simple Network Management Protocol) for managing and monitoring network components and can send SNMP messages to IP addresses. It supports SNMP MIB II and its traps in their full functionality in the unified code.
EN | 97 VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual Alarm connections You can select how the unit responds to an alarm. In the event of an alarm, the unit can automatically connect to a pre-defined IP address. You can enter up to ten IP addresses to which the unit will connect in sequence in the event of an alarm, until a connection is made. You can also select which camera image should automatically be shown first on the receiver in the event of an alarm.
EN | 98 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Auto-connect: Select the On option to automatically re-establish a connection to one of the previously specified IP addresses after each restart, after a connection breakdown or after a network failure. Note Dual Streaming compatible units only: Stream 2 is always transferred for alarm connections. Bear this fact in mind when assigning the profile (see page 72).
EN | 99 VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual Motion detector The unit has an integrated video sensor that can detect changes in the video signal on the basis of image processing. Such changes are due primarily to movements in the camera's field of view. You can configure the video sensor for any encoder, i.e. for any connected camera. The sensitivity of the video sensor can be adjusted, so that an alarm is generated only if specified values are exceeded.
EN | 100 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Caution Reflections of light (off glass surfaces etc.), switching lights on or off or changes in the light level caused by cloud movement on a sunny day can trigger unintended responses from the video sensor and generate false alarms. Run a series of tests at different times of the day and night to ensure that the video sensor is operating as intended.
EN | 101 VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual Tamper protection Various options for tamper protection allow you counteract typical attempts to tamper with cameras and video lines. Run a series of tests at different times of the day and night to ensure that the video sensor is operating as intended. Global change % You can define the percentage of sensor fields that must register a change simultaneously before generating an alarm.
EN | 102 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 – If necessary, click Select all to select the entire video frame for monitoring. – Right-click any fields you wish to deactivate. “Inactive” fields are marked white. – Click OK to save the configuration. – Click the close button X in the window title bar to close the window without saving the changes. Relay configuration (audio versions only) You can configure the switching behavior of the five relay outputs separately.
EN | 103 VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual Relay follows: If required, select a specific event that will trigger the relay.
EN | 104 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 COM1 You can configure the parameters of the RS232/485 serial interface to meet your requirements. Note If the unit is working in multicast mode (see page 57 onward), the first remote location to establish a video connection to the unit is also assigned the transparent data connection.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 105 Baud rate: Select the value for the transmission rate in bit/s. Data bits: The number of data bits per character cannot be changed. Stop bits: Select the number of stop bits per character. Parity check: Select the type of parity check. Interface mode: Select the desired protocol for the serial interface. Half-duplex mode: Choose the setting appropriate for your application. Bosch Security Systems | 2006-07 | V1.
EN | 106 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 COM2 (audio versions only) Serial port function: Select the desired function from the list. If you wish to use the additional RS232 serial interface (9-pin sub-D socket) to transmit transparent data, select Transparent. Select Terminal if you wish to operate the unit from a terminal. Baud rate: Select the value for the transmission rate in bit/s. Data bits: The number of data bits per character cannot be changed.
EN | 107 VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual Network The settings in this screen are used to integrate the unit in an existing network. Caution Changes to the IP address, subnet mask or gateway address are transferred to the unit by clicking Set. However, they only take effect after the unit is restarted. – Click Set after entering a new IP address. – Enter the old IP address followed by /reset (for example 192.168.0.88/reset) in your Web browser's address bar.
EN | 108 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Ethernet link type: If the unit is connected to the network via a switch, both must have the same default for the type of network connection. If necessary, ask your network administrator what value the switch is set to. The Auto setting automatically detects the network connection. If necessary, you can specify the value 10 or 100 MBit/s for full or half-duplex mode (FD or HD) or 1 GBit/s FD.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 109 Multicasting In addition to a 1:1 connection between an encoder and a single receiver (unicast), the unit can enable multiple receivers to receive the video signal from an encoder simultaneously.
EN | 110 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 The multicast address can be the same for multiple streams. However, it will be necessary to use a different port in each case so that multiple data streams are not sent simultaneously using the same port and multicast address. Note The settings must be made individually for each video input and, on Dual Streaming compatible units, for each stream.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 111 Note Audio signals are only transmitted if the audio function is activated on the Audio Stream configuration page (see page 78). Multicast port 1: (audio versions only) Enter the port address of the separate audio stream here. Version information The hardware and firmware version numbers are for information only and cannot be changed. Keep a record of these numbers in case technical assistance is required.
EN | 112 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Livepage configuration In this window you can customize the appearance of the LIVEPAGE to suit your requirements. You can opt to have selected information and controls displayed in addition to the video image. Individual background graphics can also be used for the main window and the upper part of the window (banner). Note You can use either GIF or JPEG images.
EN | 113 VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual Logo URL: Enter the path to a suitable background graphic in this field. The image can be stored on a local computer, the local network or at an Internet address. If necessary, click Search to find a suitable image on the local network. Device logo URL: Enter the path for a suitable image in the upper part of the window (banner). The image can be stored on a local computer, the local network or at an Internet address.
EN | 114 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Save event log: Check this option to save event messages in a text file on your local computer. You can then view, edit and print this file with any text editor or the standard Office software. Save system log: Check this option to save system messages in a text file on your local computer. You can then view, edit and print this file with any text editor or the standard Office software.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 115 Firmware and configuration upload Firmware update: The unit is designed so that its functions and parameters can be updated via firmware. To do this, transfer the current firmware package to the unit via the selected network. It will then be automatically installed there. In this way, a unit can be serviced and updated remotely without a technician having to change the installation on site.
EN | 116 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 – In the address field of the browser, enter /main.htm (for example, 192.168.0.88/main.htm). – Repeat the upload. Configuration download: You can save configuration data for the unit on a computer and then load saved configuration data from a computer to the unit. – Click the Download button. A dialog box opens. – Follow the on-screen instructions to save the current settings.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 117 Function test The unit offers a range of configuration options. You should therefore check that it is functioning correctly after installation and configuration. The function test is the only way to ensure that the unit operates as expected in the event of an alarm.
EN | 118 Configuration using a Web browser Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Bosch Security Systems | 2006-07 | V1.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual Operation EN | 119 6 Operation with Microsoft Internet Explorer A computer with Microsoft Internet Explorer (version 6.0 or higher) can receive live images from the unit, control cameras or other peripherals and play back sequences stored on the local hard drive. Note Make sure the graphics card is set to 16- or 32-bit color depth and that Microsoft Virtual Machine is installed and activated on your PC.
EN | 120 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Establishing the connection To use the unit in your network, you must assign it an IP address that is valid in your network. The following default address is preset at the factory: 192.168.0.1 – Start the Web browser. – Enter the unit's IP address as the URL. The connection is established and after a short time you will see the LIVEPAGE with the video image.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 121 The LIVEPAGE Once the connection is established, the Web browser displays the LIVEPAGE. It shows the live video image on the right of the browser window. Depending on the configuration, various text overlays may be visible on the live video image (see Display stamping, page 69). Other information may be shown next to the live video image on the Livepage.
EN | 122 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Camera control The options for controlling peripheral devices (for example a pan/tilt camera head or a dome camera) are dependent on the unit type installed and on the configuration of the VIP X1600. If a controllable unit is connected and configured, the operating items for controlling the peripheral device can be seen to the left of the video image. – To control a peripheral, click the appropriate controls.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 123 Triggering relay (audio versions only) With the relay on the audio versions, you can trigger different units (such as lamps or the door opener). – To activate this, click the icon for the corresponding relay next to the video image. The icon will be red when the relay is activated. System log / Event log The System log field contains information about the operating status of the unit and the connection.
EN | 124 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Saving snapshots You can save individual images from the video sequence currently shown on the LIVEPAGE in JPEG format on your computer's hard drive. – Click the icon for saving single images. The image is saved at a resolution of 704 × 576 pixels (4CIF/D1). The storage location depends on the configuration of the unit (see page 114).
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 125 – Insert the CD into the computer's CD-ROM drive. If the CD does not start automatically, open the CD in Windows Explorer. – Open the MPEG viewer directory and copy the MPEGViewer.exe file to your computer's hard drive. – If necessary, you can also start the MPEG viewer by double-clicking the MPEGViewer.exe file.
EN | 126 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 The MEDIA-REPLAY page The integrated hard drive means the unit can be used as a digital video recorder for local long-term recording. The MEDIA-REPLAY page for playing back recorded video sequences can be accessed from the LIVEPAGE and from SETTINGS. – Click in the navigation bar in the upper section of the window on the MEDIA-REPLAY link. The playback page appears.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 127 Selecting recordings In the left section of the page, first select the partition whose recordings you want to view. All sequences that are saved in the partition are displayed in the list. A running number (track) is assigned to each sequence. Start time and stop time, recording duration, number of alarms, and recording type are displayed. – Click a partition name from the list to display the recordings for this partition.
EN | 128 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 – If required, drag the green arrow to the point in time at which the playback should begin. Alternatively you can double-click directly in the gray time interval or in the timescale to jump to the position selected in this manner. The date and time display below the bar provides orientation to the second. You can control playback by means of the buttons below the video image.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 129 Bookmarks In addition, you can set markers in the sequences, so-called bookmarks, and jump directly to these. These bookmarks are indicated as small yellow arrows above the time interval. Use the bookmarks as follows: Jump to the previous bookmark Set bookmark Jump to the following bookmark – Right-click a bookmark to delete it.
EN | 130 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Backup You can back up the videosequences or single images stored on the hard drive of the unit to the computer's hard drive. First select the required sequence as described in the previous section.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 131 Installing MPEG viewer You can play back saved video sequences using the MPEG viewer from Bosch Security Systems, which can be found on the product CD supplied (see Components supplied, page 9). Note Suitable MPEG ActiveX software must be installed on the computer in order to play back saved video sequences using the MPEG viewer. Further information can be found on page 29. – Insert the CD into the computer's CD-ROM drive.
EN | 132 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Hardware connections between video servers You can easily connect a VideoJet 8008 or VideoJet 8004 with connected cameras as a sender, and a suitable MPEG-4 compatible hardware decoder (such as the VIP XD) with a connected monitor as a receiver via an Ethernet network connection. In this way it is possible to cover long distances without the need for major installation or cabling work.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 133 Connecting alarm With the appropriate configuration, a connection between a sender and a receiver is made automatically when an alarm is triggered (see page 97). After a short time the live video image from the sender appears on the connected monitor. This option can also be used to connect a sender and a compatible receiver using a switch connected to the alarm input. You do not need a computer to make the connection in this case.
EN | 134 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Closing the connection The connection can be closed using a terminal program or Web browser. Closing the connection with a terminal program – Start the terminal program (see page 25) and enter command i in the main menu to switch to the IP menu. – In the IP menu, enter command a to deactivate automatic connection. Closing the connection with a Web browser – Use the Web browser to connect to the receiver. You see its home page.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 135 Operating options on the front panel VideoJet 8008 and VideoJet 8004 have different operating and display elements on the front panel (see page 15). You can display some of the most important configuration parameters on the screen. However, it is not possible to change the parameters here. – Press the Menu/Exit key. The menu opens. You can see the first parameter (IP Address) and the configured value.
EN | 136 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Video locked Indicator of the camera inputs at which there is currently a video signal (labeled O). Input pin states Indicator of the alarm inputs at which there is currently an alarm (labeled H). EthTX EthRX Current data transmission speed to and from the unit. HDD Throughput Current recording speed on the hard drive. SW version Firmware version number of the unit. HW version Hardware version number of the unit.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 137 System uptime Operating time of the unit since the last power on or since the last reset (in days, hours, minutes and seconds). Encoder status Indication of the correct operation of the encoder (labeled +). Bosch Security Systems | 2006-07 | V1.
EN | 138 Operation Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Bosch Security Systems | 2006-07 | V1.
EN | 139 VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual Maintenance and upgrades 7 Testing the network connection You can use the ping command to check the connection between two IP addresses. This allows you to test whether a unit in the network is active. – Open the DOS command prompt. – Type ping followed by the IP address of the unit. If the unit is found, the response appears as Reply from ... followed by the number of bytes sent and the transmission time in milliseconds.
EN | 140 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Repairs Caution Never open the housing of the unit. The unit does not contain any user-serviceable parts. Ensure that all maintenance or repair work is carried out only by qualified personnel (electrical engineers or network technology specialists). In case of doubt, contact your dealer's technical service center. Transfer and disposal The device should only be passed on together with this installation and operating manual.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 141 8 Appendix Troubleshooting If you cannot resolve a fault, please contact your supplier or systems integrator or go directly to Bosch Security Systems Customer Service. The version numbers of the internal processors can be viewed on a special page. Make a note of this information before contacting Customer Service. – In the address field of the browser, enter /version.htm after the unit's IP address (for example 192.168.0.
EN | 142 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Malfunction Possible causes Solution No connection established, no image transmission. The unit's configuration. Check all configuration parameters. Faulty installation. Check all cables, plugs, contacts and connections. Wrong IP address. Check the IP addresses (terminal program). Faulty data transmission within the LAN. No audio transmission to remote station. The unit does not report an alarm.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 143 LEDs The VideoJet 8008 and VideoJet 8004 network video servers are equipped with a number of LEDs that show the operating status and can give indications of possible malfunctions: Power Not lit: Unit is switched off. Lit green: Unit is switched on, not connected.
EN | 144 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 RS232/485 interface Options for using the serial interface include transferring transparent data, controlling connected units or operating the unit with a terminal program. Depending on the setting, the serial interface uses the RS232 or RS422/485 standards. The standard that is used depends on the current configuration (see pages 60 and 104). RJ45 socket pin assignment The pin assignment depends on the standard used.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 145 RS232 interface (audio versions only) The second serial interface can be used to transmit transparent data or for using the unit with a terminal program. It uses the RS232 standard.
EN | 146 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Terminal block The terminal block is used for connecting alarm switches.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 147 Second terminal block (audio versions only) The second terminal block contains several contacts for: ❚ Relay outputs ❚ Serial data transmission ❚ Audio functions ❚ Power supply Options for using the serial interface include transferring transparent data, controlling connected units or operating the unit with a terminal program.
EN | 148 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Glossary Brief explanations of some of the terms and abbreviations used in this manual are given below. 10/100/1000 Base-T IEEE-802.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 149 MPEG-4 A further development of MPEG-2 designed for transmitting audiovisual data at very low transfer rates (for example over the Internet) Net mask A mask that explains which part of an IP address is the network address and which part is the host address. It is usually written in dotted decimal notation, for example “255.255.255.
EN | 150 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Technical data: VideoJet 8008 Unit Operating voltage 90 to 250 V AC, 50/60 Hz Power consumption Maximum of 60 VA LAN interface 1 × Ethernet 10/100/1000 Base-T, automatic adjustment, half/full duplex, RJ45 Data interface 1 × RS232/RS422/RS485, bidirectional, RJ45 Alarm inputs 10 × push-in terminal (non-isolated closing contact), max. activation resistance 10 Ohm Video inputs 8 × BNC socket 0.7 to 1.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 151 Protocols/standards Video standards PAL, NTSC Video coding protocols MPEG-4, JPEG Video data rate 1 MBit/s to 5 MBit/s per channel Image resolutions (PAL/NTSC) 704 × 576/480 pixels (4CIF/D1) 704 × 288/240 pixels (2CIF) 352 × 576/480 pixels (1/2 D1) 352 × 288/240 pixels (CIF) 176 × 144/120 pixels (QCIF) Overall delay 120 ms (PAL/NTSC) Image refresh rate 1 to 50/60 fields/s variable (PAL/NTSC), Field/image-based encoding
EN | 152 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Technical data: VideoJet 8008 with audio Unit Operating voltage 90 to 250 V AC, 50/60 Hz Power consumption Maximum of 60 VA LAN interface 1 × Ethernet 10/100/1000 Base-T, automatic adjustment, half/full duplex, RJ45 Data interface 1 × RS232/RS422/RS485, bidirectional, RJ45 1 × RS232, 9-pin. sub-D socket Alarm inputs 10 × push-in terminal (non-isolated closing contact), max.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual Storage conditions Temperature: –20 to +60 °C (–4 to +140 °F) relative humidity: 0 to 95%, non-condensing, maximum altitude 10,000 m Regulatory approvals CE: IEC 60950; UL 1950; AS/NZS 3548; EN 55103-1, -2; EN 55130-4; EN 55022; EN 55024; EN 61000-3-2; EN 61000-3-3; FCC 47 CFR Chapter 1 Part 15 Dimensions (W × H × D) 409.2 × 48.6 × 351.5 mm (16.11 × 1.91 × 13.
EN | 154 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Technical data: VideoJet 8004 Unit Operating voltage 90 to 250 V AC, 50/60 Hz Power consumption Maximum of 60 VA LAN interface 1 × Ethernet 10/100/1000 Base-T, automatic adjustment, half/full duplex, RJ45 Data interface 1 × RS232/RS422/RS485, bidirectional, RJ45 Alarm inputs 10 × push-in terminal (non-isolated closing contact), max. activation resistance 10 Ohm Video inputs 8 × BNC socket 0.7 to 1.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual EN | 155 Protocols/standards Video standards PAL, NTSC Video coding protocols MPEG-4, JPEG Video data rate 1 MBit/s to 5 MBit/s per channel Image resolutions (PAL/NTSC) 704 × 576/480 pixels (4CIF/D1) 704 × 288/240 pixels (2CIF) 352 × 576/480 pixels (1/2 D1) 352 × 288/240 pixels (CIF) 176 × 144/120 pixels (QCIF) Overall delay 120 ms (PAL/NTSC) Image refresh rate 1 to 50/60 fields/s variable (PAL/NTSC), Field/image-based encoding
EN | 156 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Technical data: VideoJet 8004 with audio Unit Operating voltage 90 to 250 V AC, 50/60 Hz Power consumption Maximum of 60 VA LAN interface 1 × Ethernet 10/100/1000 Base-T, automatic adjustment, half/full duplex, RJ45 Data interface 1 × RS232/RS422/RS485, bidirectional, RJ45 1 × RS232, 9-pin. sub-D socket Alarm inputs 10 × push-in terminal (non-isolated closing contact), max.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual Storage conditions Temperature: –20 to +60 °C (–4 to +140 °F) relative humidity: 0 to 95%, non-condensing, maximum altitude 10,000 m Regulatory approvals CE: IEC 60950; UL 1950; AS/NZS 3548; EN 55103-1, -2; EN 55130-4; EN 55022; EN 55024; EN 61000-3-2; EN 61000-3-3; FCC 47 CFR Chapter 1 Part 15 Dimensions (W × H × D) 409.2 × 48.6 × 351.5 mm (16.11 × 1.91 × 13.
EN | 158 Appendix Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 Bosch Security Systems | 2006-07 | V1.
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual 9 Index A Activating audio function 78 Activating partition 39, 87 Actuator 21 Alarm 51, 122 Alarm input 14, 21 Alarm message 70 Alarm recording 90 Alarm sources 95 Alarm tracks 42, 43, 90, 91 Audio connections 22 Audio input channel 78 Audio output channel 79 Audio settings 78 Auto-connect 54, 98 B Backup 130 Banner 112 Basic data 47 Baud rate 37, 61, 75, 105 Bookmarks 129 Brightness 71 Browser window 121 C Cables 17 Camera 61, 104 Camera
EN | 160 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 E Echo 26 Editing a partition 85 Electromagnetic compatibility 6 Encoder 34 Encoder numbering 34, 58, 72, 110 Encoding 11 EPROM 115 Establishing the connection 30, 120 Event log 113, 123 F False alarms 100 Filetracks 41, 89 Firmware update 115 Format 46, 94 Front panel 15, 135 FTP server 80, 81 Function test 117 G Gateway 56, 107 H Half-duplex mode 61, 105 Hardware error 15 Heat 17, 18 Heat load 17 I Identification 6, 47, 64 IGMP 5
VideoJet 8008 / VideoJet 8004 | Installation and Operating Manual N Network 21, 55, 107 Network connection 24 Number of connections 31, 121 O Operation 7, 119 Overview of functions 11 P Parameters 27 Parity 61, 105 Partition 82, 87 Partition name 45, 92 Partitioning 82 Password 31, 65, 121 Password protection 48, 65 Peripheral device control 122 Picture settings 71 Pin assignment 144, 145 Playback 126 Playback button 128 Post-alarm duration 43, 91 Power off 24 Power on 24 Power supply 24 Power switch 24 Pr
EN | 162 Installation and Operating Manual | VideoJet 8008 / VideoJet 8004 T Tamper protection 101 Target data rate 37, 75 Technical data VideoJet 8004 154 VideoJet 8004 with audio 156 VideoJet 8008 150 VideoJet 8008 with audio 152 Terminal 60, 62, 104, 106 Test 117 Time 50, 67 Time recording 40, 88 Time server 67 Time server IP address 67 Time server protocol 67 Time signal 67 Time zone 67 Total size 46, 94 Total time 46, 94 Transmission parameters 25 Transmission rate 61, 62, 105, 106 Transmission stand
Bosch Sicherheitssysteme GmbH Robert-Koch-Straße 100 85521 Ottobrunn Germany www.bosch-sicherheitssysteme.de Bosch Security Systems B.V. P.O. Box 80002 5600 JB Eindhoven The Netherlands www.boschsecuritysystems.com Copyright © 2006 BOSCH Sicherheitssysteme GmbH Subject to change.