AutoDome Power Supply Boxes VG4-A-PSU0 | VG4-A-PSU1 | VG4-A-PSU2 en Installation Guide
AutoDome Power Supply Boxes Table of Contents | en 3 Table of Contents 1 Important Safety Instructions 5 1.1 Safety precautions 5 1.2 Important safety instructions 6 1.3 Important Notices 8 1.4 UL certification 10 1.5 Bosch notices 10 2 Installing the Power Supply Box 12 2.1 Unpacking 12 2.1.1 Parts List 12 2.1.2 Optional Parts List 12 2.1.3 Description 13 2.1.4 Tools Required 13 2.2 Pre-installation Check List 13 2.3 Mount the Power Supply Box 15 2.3.
en | Table of Contents AutoDome Power Supply Boxes 3 Cable and Wire Standards 24 3.1 Power 24 3.2 Wire Distance Guide 24 3.3 Video and Control Cables 25 3.3.1 Using Coaxial Cable to Transmit Video and Control 25 3.3.2 Using UTP to Transmit Video and Control 26 3.3.3 Using Ethernet to Transmit Video and Control 27 3.3.4 Using Multi-mode Fiber Optic to Transmit Video and Control 27 3.3.5 Using a Fiber Optic Ethernet Media Converter to Transmit Video and Control 28 3.
AutoDome Power Supply Boxes 1 Important Safety Instructions | en 5 Important Safety Instructions Read, follow, and retain all of the following safety instructions. Heed all warnings on the unit and in the operating instructions before operation. 1.1 Safety precautions DANGER! High risk: This symbol indicates an imminently hazardous situation such as “Dangerous Voltage” inside the product. If not avoided, this will result in an electrical shock, serious bodily injury, or death.
en | Important Safety Instructions 1.2 AutoDome Power Supply Boxes Important safety instructions Read, follow, and retain for future reference all of the following safety instructions. Heed all warnings on the unit and in the operating instructions before operating the unit. 1. Cleaning - Unplug the unit from the outlet before cleaning. Follow any instructions provided with the unit.
AutoDome Power Supply Boxes 6. Important Safety Instructions | en 7 Power sources - Operate the unit only from the type of power source indicated on the label. Before proceeding, be sure to disconnect the power from the cable to be installed into the unit. – For battery powered units, refer to the operating – For external power supplied units, use only the instructions. recommended or approved power supplies. – For limited power source units, this power source must comply with EN60950.
en | Important Safety Instructions 9. AutoDome Power Supply Boxes Replacement parts - Be sure the service technician uses replacement parts specified by the manufacturer, or that have the same characteristics as the original parts. Unauthorized substitutions may cause fire, electrical shock, or other hazards. 10. Safety check - Safety checks should be performed upon completion of service or repairs to the unit to ensure proper operating condition. 11.
AutoDome Power Supply Boxes Important Safety Instructions | en 9 Environmental statement - Bosch has a strong commitment towards the environment. This unit has been designed to respect the environment as much as possible. Power lines: An outdoor system should not be located in the vicinity of overhead power lines, electrical lights, or power circuits, or where it may contact such power lines or circuits.
en | Important Safety Instructions 1.4 AutoDome Power Supply Boxes UL certification Disclaimer Underwriter Laboratories Inc. (“UL”) has not tested the performance or reliability of the security or signaling aspects of this product. UL has only tested fire, shock and/or casualty hazards as outlined in UL's Standard(s) for Safety for Closed Circuit Television Equipment, UL 2044. UL Certification does not cover the performance or reliability of the security or signaling aspects of this product.
AutoDome Power Supply Boxes Important Safety Instructions | en 11 Copyright This manual is the intellectual property of Bosch Security Systems and is protected by copyright. All rights reserved. Trademarks All hardware and software product names used in this document are likely to be registered trademarks and must be treated accordingly. Note: This manual has been compiled with great care and the information it contains has been thoroughly verified.
en | Installing the Power Supply Box AutoDome Power Supply Boxes 2 Installing the Power Supply Box 2.1 Unpacking This equipment should be unpacked and handled with care. If an item appears to have been damaged in shipment, notify the shipper immediately. Verify that all the parts listed in the product's Parts List below are included. If any items are missing, notify your Bosch Security Systems Sales or Customer Service Representative.
AutoDome Power Supply Boxes 2.1.3 Installing the Power Supply Box | en 13 Description This chapter details how to install an AutoDome power supply box. Any variations to the installation procedures are noted. These power supply boxes are intended for use with the VGA-PEND_ARM Arm Mount, VGA-A-9543 Pipe Mount, and the VG4-A-9230 or VGA-ROOF-MOUNT Roof Parapet Mount.
en | Installing the Power Supply Box 3. AutoDome Power Supply Boxes Install all rough wiring including: power, control, video coax, alarms I/O, relay I/O, and fiber optic cabling. Refer to Section 3 Cable and Wire Standards, page 24 for video and control protocol methods. 4. Analog AutoDome: If you plan to use the RS232 or RS485 protocol to control the AutoDome, refer to Section 3.4.2 Controlling the AutoDome via the RS232 Protocol, page 30, or Section 3.4.
AutoDome Power Supply Boxes 2.3 Installing the Power Supply Box | en 15 Mount the Power Supply Box Before mounting the power supply box decide if you will be wiring the box through the holes in the bottom or back of the box. If wiring the box through the back, move the two (2) seal plugs to the bottom holes before mounting. NOTICE! Use 3/4-inch NPS (20-mm) fittings for the holes on the bottom and back of the box. Use 1/2-inch NPS (15-mm) fittings for the side holes. Figure 2.1 1.
en | Installing the Power Supply Box 5. AutoDome Power Supply Boxes Attach the 3/4 in. (20 mm) watertight pipe fittings (not supplied) to the holes of the power supply box through which you will run the power, video, and control data wires. 2.3.1 Attach Cover Door 1. Compress the bottom hinge pin by pushing the pin lever down and then rotate it behind the hinge pin stop. The power box cover door provides a hinge pin stop to hold the bottom hinge open while attaching the door.
AutoDome Power Supply Boxes 3. Installing the Power Supply Box | en 17 While holding the top hinge pin open, position the cover door to the power supply box and align its hinges. 4. When the hinges are aligned, release the top hinge pin to engage its mating hinge on the power box. Then release the bottom hinge pin from the hinge pin stop to complete attaching the cover door to the power supply box.
en | Installing the Power Supply Box 2.4 AutoDome Power Supply Boxes Route Wires and Attach Connectors Power wires must be routed to the left (front) side of the power supply box through a separate conduit. All video, control, and alarm wires must be routed through a second conduit to the right side of the box. Refer to Section 3 Cable and Wire Standards, page 24 for methods of transmitting video and data, and for wire specifications.
XF103 J101 DOME 54321 HTR P107 XF101 (FUSE) J102 NC 24V P106 GND TXD RXD Figure 2.3 J103 (LED) 24V P105 C+ C- GND TXD RXD XF102 P101 19 (FUSE) Installing the Power Supply Box | en (FUSE) AutoDome Power Supply Boxes C+ C- VG4-A-PSU1 or VG4-A-PSU2 Power Supply Box 1 24/120/230 VAC 5 Coax, UTP Video, or Ethernet Wire Power In 2 P101 Connector 3 Ground Connection 4 Transformer 6 Control Wire 7 24 VAC Power Out 8 P107 Connector Bosch Security Systems, Inc.
en | Installing the Power Supply Box – AutoDome Power Supply Boxes The second method is to bypass the power supply box and route the video, control, and alarm wires directly to the AutoDome Arm Mount, Pipe Mount, or to the Roof Parapet Mount. You connect only the power wires inside the power supply box.
AutoDome Power Supply Boxes 2.4.2 Installing the Power Supply Box | en 21 Wiring the Power Supply Box 1. Route the high voltage 115/230 VAC lines through the conduit fitting on the left side of the box. or Route the 24 VAC lines through the conduit fitting on the left side of the box. NOTICE! The power supply box with transformer comes with a barrier that separates the high voltage side on the left from the low voltage 24 VAC side on the right. 2.
en | Installing the Power Supply Box 2.4.3 AutoDome Power Supply Boxes Power Supply Box Connections The following figure is a detailed illustration of the power XF102 CONTROL IN/OUT P106 GND T XD RXD C+ CONTROL TO DOM ME P105 GND T XD RXD C- C+ J103 J103 (LED) 123 (FUSE)) DOME HTR P107 XF101 (FUSE)) P101 24V NC 24V (FUSE)) J101 1 J102 5 4 3 2 1 XF103 supply box, which includes the fuse specifications.
AutoDome Power Supply Boxes Installing the Power Supply Box | en 23 The following table lists the Power Supply Box connectors: No.
en | Cable and Wire Standards 3 AutoDome Power Supply Boxes Cable and Wire Standards CAUTION! Installation should only be performed by qualified service personnel in accordance with the National Electrical Code or applicable local codes. CAUTION! All wires for installation applications must be routed through a grounded conduit. 3.1 Power 24/115/230 VAC Copper Wire 3.2 To comply with local codes. Wire Distance Guide 24 V to AutoDome AutoDome 100, Indoor VA / 14 AWG (2.5 16 AWG (1.
AutoDome Power Supply Boxes 3.3 3.3.1 Cable and Wire Standards | en 25 Video and Control Cables Using Coaxial Cable to Transmit Video and Control CAUTION! 600 Series AutoDome: If you are using coaxial cable to transmit video and data between the AutoDome and the head-end, you must use the coax cable with ferrite included in the AutoDome packaging.
en | Cable and Wire Standards 3.3.2 AutoDome Power Supply Boxes Using UTP to Transmit Video and Control Unshielded twisted pair (UTP) cable terminated with RJ45 male connectors are used to transmit composite video using pins 1(+) and 2(-). Typically, a Coax to UTP cable converter is required at the head-end of the system. Bilinx control data can also be sent over the same two video wires (1 & 2).
AutoDome Power Supply Boxes 3.3.3 Cable and Wire Standards | en 27 Using Ethernet to Transmit Video and Control CAUTION! Ethernet connections must be made to non-exposed (indoor) networks only. The AutoDome VG5 700 series connects to a 10 Base-T/100 Base-TX network either directly or via a switch. Both video and control are transmitted over a standard TCP/IP network using the built-in Web server.
en | Cable and Wire Standards 3.3.5 AutoDome Power Supply Boxes Using a Fiber Optic Ethernet Media Converter to Transmit Video and Control The fiber optic media converter kit, available for AutoDome 700 Series cameras, is designed to transmit 10/100 Mbps Ethernet signals over fiber optic cable using 10/100 Mbps Small Formfactor Pluggable (SFP) modules.
AutoDome Power Supply Boxes Cable and Wire Standards | en 3.4 Control-only Cables 3.4.1 Controlling the AutoDome via Biphase 29 (Shielded 2-wire, half-duplex, multi-drop, 5000 ft. cable limit) Biphase is the standard Bosch protocol used to send Pan/Tilt/ Zoom control over 2-wire shielded twisted pair (STP) terminated with a 100 Ω terminal resistor. The AutoDome has a 100 Ω termination resistor between the Biphase C+ and C- terminals. CAUTION! The Biphase shield must be connected to the head end only.
en | Cable and Wire Standards AutoDome Power Supply Boxes In a daisy chain configuration, where multiple domes are connected in series, the 100 Ω resistor must be removed from all but the last dome. You can daisy chain a maximum of four (4) AutoDomes. 100 Ω Figure 3.
AutoDome Power Supply Boxes Cable and Wire Standards | en Wire Type Distance Maximum Baud Rate Voltage Termination Slide Switch Figure 3.4 3-wire (TXD, RXD, common) 15 m (50 ft) 57.6 Kb ± 15 V 100 Ω Away from LEDs (factory default) Connections for RS232 Operation 1 2 C- (Biphase) C+ (Biphase) 7 8 AutoDome Data In/Out P105/P106 Connector in Power 3 4 5 6 Earth Ground RxD TxD Signal Ground 9 10 11 12 Supply Box Head End RS232 TxD RxD Ground Figure 3.
en | Cable and Wire Standards 3.4.3 AutoDome Power Supply Boxes Controlling the AutoDome via the RS485 Protocol 2-wire (shielded), half-duplex, differential, multi-drop (32 nodes), 4000 ft cable limit) RS485 is capable of controlling a true multi-drop network and is specified for up to 32 drivers and 32 receivers on a single 2wire bus. The AutoDome uses the 2-wire mode, although RS485 can be connected in a 2- or 4-wire mode.
AutoDome Power Supply Boxes Cable and Wire Standards | en 33 100 Ω Figure 3.6 Connections for RS485 Operations 1 C- (Biphase) 2 C+ (Biphase) 7 8 AutoDome Data In/Out P105/P106 Connector in Power Supply 3 4 5 6 9 10 11 12 Box Head End RS485 Data + Data Ground Earth Ground RxD TxD Signal Ground Figure 3.
en | Cable and Wire Standards 3.5 AutoDome Power Supply Boxes Fiber Optic Module with an RS232/RS422 Controller An AutoDome with a fiber optic module is prewired to operate with Biphase signals only. This section describes the procedures necessary to control a VG5 series AutoDome fitted with a fiber optic kit using an RS232 controller or a Pelco® RS422 controller.
AutoDome Power Supply Boxes 7. Cable and Wire Standards | en 35 Connect the green (RxD) wire to the C+ pin on the P106 DO HTR 5432 24 VAC P107 XF101 connector. NC 24V P106 GND TXD RXD Figure 3.8 J103 J1 (LED) 24V P105 C+ C- GND TXD RXD XF102 P101 C+ C- Detail of P106 Connections 1 2 Green RxD wire connected to C+ Blue Ground wire connected to C- 8. Connect the fiber optic cable from the AutoDome to the LTC 4629. 9. Close the door to the power supply unit. 10.
en | Cable and Wire Standards AutoDome Power Supply Boxes 11. Return the bubble to the AutoDome housing. 12. Return power to the power supply box. 3.6 Audio Cables The VG5 700 Series AutoDome is capable of receiving line input audio signals and transmitting it over a network. The audio signal is transmitted one-way and in sync with the video signals. Audio Line Input Specifications Max. Input Voltage 5.
AutoDome Power Supply Boxes Cable and Wire Standards | en 37 Audio Connections 1. Remove the 100 Ω termination resistor from the Biphase terminals. 2. Connect the audio line level source to the Biphase C+ input terminal. 3. Connect the audio signal ground to the Biphase C- input terminal. The following figure illustrates the connections for audio over an IP network. Figure 3.
en | Cable and Wire Standards F.01U.250.895 | 1.0 | 2011.08 AutoDome Power Supply Boxes Installation Guide Bosch Security Systems, Inc.
Bosch Security Systems, Inc. 850 Greenfield Road Lancaster, PA 17601 U.S.A. www.boschsecurity.com © Bosch Security Systems, Inc.
