DM 2610920458 2-04 2/19/04 12:29 PM Page 1 Operating/Safety Instructions Model 335 Plunge Router Attachment • • • • • Safety Assembly Operation Service Parts Warranty Parlez-vous français? Voir page 12 ¿Habla español? Vea página 23 P.O. Box 1468 Racine, Wisconsin 1-800-437-3635 http://www.dremel.
DM 2610920458 2-04 2/19/04 12:29 PM Page 2 Power Tool Safety Rules Read and understand all instructions. Failure to follow all instructions listed ! WARNING below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS Make sure to read and understand the Owner’s Manual for your Dremel Rotary Tool Models 275, 285, 395 & 398.
DM 2610920458 2-04 2/19/04 12:29 PM Page 3 Operating Controls Adjustment Nut, Upper Depth Stop FIG. 1 Dremel Rotary Tool Release Button Speed Control Mounting Wrench & Storage Area Adjustment Nut, Lower Hand Grip (turn to lock) Hand Grip (stationary) Collet Nut Wrench Storage Area (Wrench not included) Shaft Lock Button Depth Scale (English/Metric) Edge Guide Circle Guide Assembling Plunge Router Attachment to your Tool ATTACHMENT FOR USE WITH DREMEL ROTARY TOOL MODELs 275, 285, 395, & 398.
DM 2610920458 2-04 2/19/04 12:29 PM Page 4 Operating Instructions ATTACHMENT FOR USE WITH DREMEL HIGH SPEED ROTARY TOOL MODELS 275, 285, 395, & 398. circular cuts. The router attachment comes assembled ready for freehand or pilot bit routing. This Router Attachment is ! WARNING not intended for use under a router or saw table.
DM 2610920458 2-04 2/19/04 12:29 PM Page 5 Adjusting Routing Depth NOTE: When making deep cuts, especially plunge cuts away from the edge of the workpiece, it is recommended to make several successive cuts progressively deeper using the depth adjustment and depth scale rather than making one single deep cut. The depth limiter can be adjusted for two depths. 1. Place your Dremel Rotary Tool and Router assembly on the workpiece. 2.
DM 2610920458 2-04 2/19/04 12:29 PM Page 6 10.Press the release button to select the 1st or 2nd routing depth (Fig. 9). NOTE: The adjustment of each routing depth should be checked with a trial cut and re-adjusted as necessary. When routing is complete, loosen the hand grip and return the router to the top position. FIG.
DM 2610920458 2-04 2/19/04 12:29 PM Page 7 Tool Lubrication Periodic cleaning and lubrication of guide posts will keep plunge action smooth. Depress and lock plunge router and evenly apply a light lubricant (i.e. petroleum jelly, cooking oil) to upper portion of guide posts. Assembling the Edge Guide For edge guide use, assemble guide rods into tool holder assembly and secure using (2) #10-24 square nuts and (2) guide rod knobs (Fig. 11). assembly on guide rods as shown.
DM 2610920458 2-04 2/19/04 12:29 PM Page 8 Edge Guide Installation 1. Install the edge guide to the plunge router mounting blocks (Fig. 12). 2. Place parallel guide against work surface with router bit in desired position. 3. Tighten thumbscrews. FIG. 12 Mounting Blocks Routing with Edge Guide Slide the flattened side of the edge guide along the work surface. Edge Guide FIG. 13 Routing Arcs and Circles 1 Remove the edge guide and attach the circle guide bracket to the guide rods (Fig. 13). 2.
DM 2610920458 2-04 2/19/04 12:29 PM Page 9 Templates Using template patterns lets you duplicate designs or letters uniformly time after time. This technique requires the use of a guide bushing. Do not use a bit that may touch the inside of the collar. Select a bit that is at least 1/16" less in diameter. In addition, special templates are easily prepared for cutting repeated patterns, special designs, inlays, and other applications.
DM 2610920458 2-04 2/19/04 12:29 PM Page 10 Dremel Parts Diagram Ref. No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Part No. 2610920042 2610920041 2610913432 2610920044 1603501018 2603345015 2604511008 2602305044 2610918203 2610918204 2610918206 2916011884 2910011191 2610358149 Description Ref. No. Spring (2) 15 Guide Post. (2) 16 Depth Marker 17 Guide Plate Assy.
DM 2610920458 2-04 2/19/04 12:29 PM Page 11 Dremel Limited Warranty Your Dremel product is warranted against defective material or workmanship for a period of one year from date of purchase. In the event of a failure of a product to conform to this written warranty, please take the following action: 1. DO NOT return your product to the place of purchase. 2. Carefully package the product by itself, with no other items, and return it, freight prepaid, along with: A.