EX14 Marine Camera EX14 Series en Instruction Manual
EX14 Marine Camera Table of Contents | en 3 Table of Contents 1 Safety 4 1.1 Important safety instructions 4 1.2 Safety precautions 4 1.3 Important notices 5 1.4 Customer Support and Service 2 Description 12 2.1 Unpacking 13 2.1.1 Parts List 13 2.1.2 Items Required for Installation 13 3 Initial Preparations 14 3.1 Installation Guidelines 14 4 Camera Mounting 15 4.1 Mounting instructions 15 5 Camera Connections 17 11 5.1 Camera Adjustments 18 5.
en | Safety EX14 Marine Camera 1 Safety 1.1 Important safety instructions Read, follow, and retain all of the following safety instructions. Heed all warnings on the unit and in the operating instructions before operating the unit. 1. Read these instructions. 2. Keep this instruction. 3. Heed all warnings. 4. Follow all instructions. 5. Clean only with dry cloth. 6. Do not block any ventilation openings. Install in 7.
EX14 Marine Camera 1.2 Safety | en 5 Safety precautions DANGER! High risk: This symbol indicates an imminently hazardous situation such as “Dangerous Voltage” inside the product. If not avoided, this will result in an electrical shock, serious bodily injury, or death. WARNING! Medium risk: Indicates a potentially hazardous situation. If not avoided, this could result in minor or moderate bodily injury. CAUTION! Low risk: Indicates a potentially hazardous situation.
en | Safety – EX14 Marine Camera Disconnect the unit's input connectors from outdoor equipment before disconnecting the grounding plug or grounding terminal. – Follow proper safety precautions such as grounding for any outdoor device connected to this unit. U.S.A. models only - Section 810 of the National Electrical Code, ANSI/NFPA No.
EX14 Marine Camera Safety | en 7 Power resupply - If the unit is forced to power down due to exceeding the specified operating temperatures, disconnect the power cord, wait for at least 30 seconds, and then reconnect the power cord. Power lines - Do not locate the camera near overhead power lines, power circuits, or electrical lights, nor where it may contact such power lines, circuits, or lights. SELV All the input/output ports are Safety Extra Low Voltage (SELV) circuits.
en | Safety EX14 Marine Camera FCC & ICES Information (U.S.A. and Canadian Models Only) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
EX14 Marine Camera Safety | en 9 INFORMATIONS FCC ET ICES (modèles utilisés aux États-Unis et au Canada uniquement) Suite à différents tests, cet appareil s'est révélé conforme aux exigences imposées aux appareils numériques de classe B, en vertu de la section 15 du règlement de la Commission fédérale des communications des États-Unis (FCC), et en vertu de la norme ICES-003 d'Industrie Canada.
en | Safety EX14 Marine Camera Printing Office, Washington, DC 20402, États-Unis, sous la référence n° 004-000-00345-4. DANGER! CSA Certified/UL Listed Class 2 adaptors must be use in order to comply with electrical safety standards. Only qualified personnel shall install any Bosch Extreme series camera and conform to all local safety codes. Bosch Security Systems, Inc.
EX14 Marine Camera Safety | en 11 Copyright This manual is the intellectual property of Bosch Security Systems and is protected by copyright. All rights reserved. Trademarks All hardware and software product names used in this document are likely to be registered trademarks and must be treated accordingly. NOTE! This manual has been compiled with great care and the information it contains has been thoroughly verified. The text was complete and correct at the time of printing.
en | Safety 1.4 EX14 Marine Camera Customer Support and Service If this unit needs service, contact the nearest Bosch Security Systems Service Center for authorization to return and shipping instructions. Service Centers USA Repair Center Telephone: 800-366-2283 Fax: 800-366-1329 E-mail: repair@us.bosch.com Customer Service Telephone: 888-289-0096 Fax: 585-223-9180 E-mail: security.sales@us.bosch.com Technical Support Telephone: 800-326-1450 Fax: 585-223-3508 or 717-735-6560 E-mail: technical.
12 2 en | Description EX14 Marine Camera Description The EX14 Marine is an all-environment camera designed specifically for marine and extreme weather applications. The 940 nm active IR option provides covert operation to not interfere with shipping navigation lights. The simple, effective design allows performance in the most challenging of environmental conditions. The housing is compact with a 4 to 9 mm varifocal lens for a variety of marine applications.
EX14 Marine Camera Description | en 13 Rugged, compact, power protected and extreme weathersealed, the EX14 Marine is an ideal camera for harsh extreme environments in day or dark conditions. The EX14 Marine comes complete with a nylon wall bracket for a quick and easy installation. 2.1 Unpacking Care should be taken when unpacking the shipped unit. Check the parts list and confirm all items have been located. Inspect the equipment thoroughly to ensure nothing was damaged in transit.
14 en | Initial Preparations 3 EX14 Marine Camera Initial Preparations 1. Determine the operating voltage at the installation site. The camera’s Voltage Regulator Board accepts 12-24 VDC/ VAC input without change to internal connections 2. Determine the optimum mounting location for the camera. See Section 4 Camera Mounting, page 15. 3. All cameras have been tested and pre-focused with telephoto setting as factory default prior to shipment.
EX14 Marine Camera 4 Camera Mounting | en 15 Camera Mounting WARNING! IMPORTANT MOUNTING INSTRUCTIONS THIS APPARATUS MUST BE SECURELY ATTACHED TO THE WALL IN ACCORDANCE WITH THE INSTALLATION INSTRUCTIONS. FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS MAY RESULT IN INJURY. CAUTION! Ensure the selected location is protected from falling objects, accidental contact with moving objects, and unintentional interference from personnel. Follow all applicable building codes. Follow these mounting guidelines: 1.
16 en | Camera Mounting 4.1 EX14 Marine Camera Mounting instructions The camera is intended to be securely mounted to a wall using the mounting bracket supplied with the enclosure. The camera has been evaluated for wall mounting using 2 in. long #10 wood screws with washers secured into a 2 x 4 stud under 1/2 in. of drywall. 1. Locate a stud in the wall and mark outside edges of stud. 2. Using the wall mount bracket as a template, align the mounting holes with the center of the stud. 3.
EX14 Marine Camera 5 Camera Connections | en 17 Camera Connections The camera unit is pre-connected with an electrically isolated power board for 24 VAC or 12 VDC operation with no wiring change or wiring polarity. Input voltage is 12 VDC to 24 VDC for DC input. The AC input range is 12 VAC to 24 VAC. Please refer to the following steps for camera power/video cable connections. The Camera is designed for use with a power/video composite cable with a diameter of 11/64 in. to 15/32 in. (4.4 mm to 11.
18 en | Camera Connections EX14 Marine Camera 4. Remove the desiccant from the plastic bag. 5. Place the desiccant into the enclosure on the side opposite of the cable connections. 6. Tighten the nut of the gland to 1.3 NM torque setting and ensure it is sealed well. 7. Perform any required adjustments as detailed in Section 5.1 Camera Adjustments, page 18 and Section 5.2 LED Array Adjustments, page 19. 8.
EX14 Marine Camera 5.2 Camera Connections | en 19 LED Array Adjustments The LED Array sensitivity has been set at the factory before shipment.
20 en | Camera Configuration 6 EX14 Marine Camera Camera Configuration Camera configuration is performed through the On-screen Display (OSD) menu. To access these menus: 1. Open the EX14 camera housing cap to access the OSD controls. 2. 3. Press the joystick button down to enter the OSD menu. Follow the instructions below to make camera adjustments. 6.1 OSD Menus The main Camera Operation menu allows you to set the following parameters: Figure 6.
EX14 Marine Camera 6.1.1 LENS Camera Configuration | en 21 Exposure Menu Select the type of lens: MANUAL or DC. Note: The default setting is DC. If you change this setting undesired operation may occur. MANUAL Select for manual iris control. Adjust the brightness of the screen by configuring the ELC level. DC Select for automatic iris control. Adjust the offset brightness of the screen by configuring the DC level. Bosch Security Systems, Inc. Instruction Manual F.01U.240.878 | 1.0 | 2011.
22 en | Camera Configuration EX14 Marine Camera E.SHUTTER Select either AUTO or FIXED control for the electronic shutter. Note: The default setting is AUTO. If you change this setting undesired operation may occur. AUTO Set for complete automatic operation of the electronic shutter, only available when lens iris control is set to Manual. FIXED Set the desired minimum shutter speed. Ten levels are available.
EX14 Marine Camera Camera Configuration | en 23 BLC (Back Light Compensation) Change the BLC setting when there is a strong backlight in the scene to get a uniform image. Select BLC ON to adjust the BLC level 5 sections (TOP / DOWN / CENTER / RIGHT / LEFT). Increase the level in areas desired to become brighter for compensation. AGC (Automatic Gain Control) This function automatically adjusts video gain to enhance the picture in darker scenes. AGC is adjustable within the range: OFF - 36 dB.
24 en | Camera Configuration 6.1.2 EX14 Marine Camera Color Menu WHITE BALANCE CONTROL Adjusts the screen color in accordance with the type of ambient light on scene. Use the following parameters: – AWC: Use this for color temperatures below 2500°C and over 9500°C (indoors) – ATW: Use this for color temperatures between 2500°C – MANUAL: The white balance is manually controlled. – PUSH LOCK: Adjusts the white balance automatically for and 9500 °C (outdoors) the current light on scene. F.01U.
EX14 Marine Camera Camera Configuration | en 25 MANUAL Adjusts RED or BLUE in accordance with the type of ambient light on scene. GAIN CONTROL Select the desired gain value. The higher the gain level, the more the scene displays that color. – R-Y GAIN: Adjusts the RED color . – B-Y GAIN: Adjusts the BLUE color. Bosch Security Systems, Inc. Instruction Manual F.01U.240.878 | 1.0 | 2011.
26 en | Camera Configuration 6.1.3 EX14 Marine Camera Day/Night Menu AUTO/COLOR/BW This function determines when the camera switches modes: – AUTO: The camera automatically switches between day and night mode depending on the light level. Note: The following default setting should not be changed: Day/Night = Auto – COLOR: The camera stays in day mode. – B/W: The camera stays in night mode. – BURST SIGNAL: If ON, the screen shows a color burst while switching to day mode from night mode.
EX14 Marine Camera 6.1.4 Camera Configuration | en 27 Function Menu MIRROR If ON is selected, the horizontal image on the screen is reversed. SHARPNESS Adjusts the image sharpness. Bosch Security Systems, Inc. Instruction Manual F.01U.240.878 | 1.0 | 2011.
28 en | Camera Configuration EX14 Marine Camera GAMMA Adjusts the Gamma level; selectable in three levels: 0.45, 0.6, 1.0 SLD (Side Light Compensation) Select this mode when the corner of the screen is darker than the center. F.01U.240.878 | 1.0 | 2011.07 Instruction Manual Bosch Security Systems, Inc.
EX14 Marine Camera Camera Configuration | en 29 HME (High Light Masking Exposure) This function masks the bright areas on the screen. The brightness of HME is adjustable. As the level of HME is increases, the masking area increases. DRC (Dynamic Range Compensation) This function is to compensate darker images when different exposures are in one scene. MOTION DETECTION Allows you to detect the movement of an object in 64 different areas of the screen, and to display an alarm on the screen.
30 en | Camera Configuration EX14 Marine Camera – ALL SET: Sets the entire screen for motion detection. – ALL CLEAR: Clears the entire screen for motion detection. F.01U.240.878 | 1.0 | 2011.07 Instruction Manual Bosch Security Systems, Inc.
EX14 Marine Camera – Camera Configuration | en 31 SENSITIVITY LEVEL: As the sensitivity level increases, smaller movements are detected. – SHOW INDI: The motion detected indicator can be selected as icon, trace or off. – DELAY OUT: The alarm signal display on the screen is delayed from 1sec to 15 sec. Bosch Security Systems, Inc. Instruction Manual F.01U.240.878 | 1.0 | 2011.
32 en | Camera Configuration 6.1.5 EX14 Marine Camera Privacy Menu PRIVACY MASKING ZONE This function sets certain areas of the screen to be hidden. Four (4) masking zones are available. – MASK 1: Adjust the masking area by using the joystick. – MASK 2: Adjust the masking area by using the joystick. – MASK 3: Adjust the masking area by using the joystick. – MASK 4: Adjust the masking area by using the joystick.
EX14 Marine Camera Camera Configuration | en 33 COLOR SET This function is to select the color of the masking cells. 6.1.6 Set Up Menu CAMERA ID Enter a camera ID as a unique identifier. Bosch Security Systems, Inc. Instruction Manual F.01U.240.878 | 1.0 | 2011.
34 en | Camera Configuration EX14 Marine Camera TITLE DISPLAY Camera title is displayed on the screen when a value is entered. – TITLE EDIT: Selects the value. – TITLE RESET: Clears the title. – TITLE POSITION SELECTION: Sets area that displays the title. If editing the title, this image is displayed, select desired characters by using the joystick. F.01U.240.878 | 1.0 | 2011.07 Instruction Manual Bosch Security Systems, Inc.
EX14 Marine Camera Camera Configuration | en 35 DPC SET (Defext Pixel Cancellation) This function automatically removes dead pixels in real time. – WHITE THR: Cancels the white defective pixels. – BLACK THR: Cancels the black defective pixels. The cancellation sensitivity of defect pixels is adjustable. For adjusting white defective pixel sensitivity, set WHITE THR. and DPC LEVEL at the same time. For adjusting black defect pixel, set BLACK THR and DPC LEVEL at the same time.
36 en | Camera Configuration EX14 Marine Camera LANGUAGE Select either English or Chinese for the language of the OSD menu. PC CONT. Set PC CONT. to ON to allow PC communication (not supported). F.01U.240.878 | 1.0 | 2011.07 Instruction Manual Bosch Security Systems, Inc.
EX14 Marine Camera Camera Configuration | en 37 EXIT – EXIT: Exit the OSD menu. – SAVE & EXIT: Exit the OSD menu after saving the current setting. – FACTORY SET: Change setting to the factory default. (make sure to SAVE & EXIT after). Note: Choosing FACTORY SET does not effect the Lens, Day & Night and ID/Title settings. Bosch Security Systems, Inc. Instruction Manual F.01U.240.878 | 1.0 | 2011.
EX14 Marine Camera 7 Troubleshooting | en 39 Troubleshooting PROBLEM POSSIBLE LIKELY SOLUTION CAUSE No Video Power supply Check input power connections at connections the cable leads. Check for loose wires No Video Power supply - If connected to DC check input Voltage range voltage range of 12–24V. If connected to AC , check input voltage range of 12–24V. Measure the voltage and current at the Input power cable. The current should be >.02 A and <1.0 A.
8 en | General Specifications EX14 Marine Camera General Specifications CCD 1/3 in. EXview HAD Resolution 540 TVL color 540 TVL monochrome Effective Pixels (H x V) NTSC: 768 x 494 PAL: 752 x 582 Day Sensitivity 0.1 lux (30 IRE, color) Night Sensitivity 0.001 lux (30 IRE, B/W), 0 lux with IR S/N Ration Greater than 50 dB (AGC off) Video Output 1 Vpp, 75 ohm Gamma Selectable -0.45, 0.6, or 1.
EX14 Marine Camera General Specifications | en Color Traffic White (RAL 9016) External Dimensions 180 x 85 x 85 mm (L x W x H) (7.1 x 3.3 x 3.3 in.) Input Cable Size 11/64 to 15/32 in. 41 (4.4 to 11.9 mm) Weight 0.7 kg (1.5 lb) bracket included Operating Temperature Range -60°C to +60°C (-76°F to +140°F) Environmental IP66, NEMA 4X NOTICE! Subject to change without notice. Bosch Security Systems, Inc. Instruction Manual F.01U.240.878 | 1.0 | 2011.
en | General Specifications F.01U.240.878 | 1.0 | 2011.07 EX14 Marine Camera Instruction Manual Bosch Security Systems, Inc.
Bosch Security Systems, Inc. 850 Greenfield Road Lancaster, PA 17601 U.S.A. www.boschsecurity.com © Bosch Security Systems, Inc.