EX36 Corner-mount No-grip Camera EX36 | EX36N en Instruction Manual
Corner-mount No-grip Camera Table of Contents | en 3 Table of Contents 1 Safety 4 1.1 Important Safety Instructions 4 1.2 Bosch Contact Information 7 2 Description 8 2.1 Unpacking 8 2.2 Parts List 8 2.2.1 Parts Included with the Product 8 2.2.2 User-Supplied Parts 9 3 Installation 10 3.1 Initial Preparations 10 3.2 Faceplate Removal 10 3.3 Input Power Connections 12 3.4 Mounting the Camera Housing 13 3.5 Camera - Directional Adjustment 15 3.
en | Safety Corner-mount No-grip Camera 1 Safety 1.1 Important Safety Instructions – Read and follow all instructions. – Keep these instructions. – Heed all warnings. – Do not use this apparatus near water. – Clean with a dry cloth only. – Do not block any ventilation openings. Install in accordance with manufacturer instructions. – Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produces heat.
Corner-mount No-grip Camera Safety | en 5 NOTICE! For best results, please read this Instruction Booklet prior to installing the EX36(N) camera. WARNING! CSA Certified/UL Listed CLASS 2 power adaptors must be used in order to comply with electrical safety standards. NOTICE! This product has been certified by CSA International to include the healthcare facility requirements of UL 2044.
en | Safety Corner-mount No-grip Camera FCC Information This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. As part of its normal operation, this device can generate radio frequency energy and if not installed and used in accordance with the installation manual may cause interference to radio communications.
Corner-mount No-grip Camera 1.2 Safety | en 7 Bosch Contact Information If this unit needs service, contact the nearest Bosch Security Systems Service Center for authorization to return and for shipping instructions. USA Repair Center Telephone: 800-566-2283 Fax: 800-366-1329 E-mail: repair@us.bosch.com Customer Service Telephone: 888-289-0096 Fax: 585-223-9180 E-mail: security.sales@us.bosch.com Technical Support Telephone: 800-326-1450 Fax: 585-223-3508 or 717-735-6560 E-mail: technical.support@us.
en | Description 2 Corner-mount No-grip Camera Description The EX36(N) Night Vision Camera has been designed with tilt on its faceplate to allow corner mounting and t provide better angle views in small rooms. The housing and faceplate consist of tough materials to withstand damage in hostile environments such as prison cells and psychiatric wards.
Corner-mount No-grip Camera 2.2.2 Description | en 9 User-Supplied Parts The following items are required for installation but are not supplied: – mounting hardware – mounting tools Bosch Security Systems, Inc. Instruction Manual F.01U.172.707 | 3.0 | 2011.
en | Installation Corner-mount No-grip Camera 3 Installation 3.1 Initial Preparations – Determine the operating voltage at the installation site. – Determine the optimum location for the camera. Refer to – All units have been tested prior to shipment. After the Section 3.4 Mounting the Camera Housing. wiring has been reconnected, check the unit’s operation before installation. – 3.
Corner-mount No-grip Camera 4. Installation | en 11 Ensure that the polycarbonate windows in the faceplate are not scratched. Figure 3.1 Faceplate Removal Number 1 2 3 Description Faceplate Housing Tamper-resistant hex screws Figure 3.2 below shows the interior layout of the EX36(N) camera assembly after the faceplate has been removed. Smaller details such as wiring and terminal blocks are omitted for clarity. Refer to the specific module sections for these details. Bosch Security Systems, Inc.
en | Installation Corner-mount No-grip Camera Figure 3.2 Layout of Modules Number 1 2 3 4 3.3 Description LED / Illuminator Board LED Voltage Regulator Board (VRB) Camera and Lens assembly Camera Voltage Regulator Board (VRB) Input Power Connections The camera unit is pre-connected with an electrically isolated power board for 24 VAC or 12 VDC operation with no wiring change or wiring polarity. Refer to Figure 3.3 and Figure 3.4, Page 13, for wiring details. Figure 3.
Corner-mount No-grip Camera Installation | en 13 Figure 3.4 Board Connections, LED Voltage Regulator Board (VRB) Number Description 1 LED Power Output 2 Voltage Regulator Board (VRB) Power Input 3.4 Mounting the Camera Housing 1. Select a suitable location that is protected from accidental damage, tampering, and environmental conditions exceeding the unit’s specifications.
en | Installation 3. Corner-mount No-grip Camera Select a mounting surface capable of supporting the combined weight of the unit and mounting hardware to anticipate all expected conditions of both temperature and vibration. 4. Secure all cabling. NOTICE! If you are installing the camera on drywall, you must use #8 screws and #8 drywall nylon plugs or a superior connection. 5. Drill holes into the mounting surface. Depending on the type of mounting surface (brick, wood, etc.
Corner-mount No-grip Camera 6. 7. Installation | en 15 Mount the housing using the supplied mounting screws. Ensure that the power and video cables are not crimped or stressed after the camera has been mounted. 3.5 Camera - Directional Adjustment Both the camera and the LED array can be adjusted for optimum picture quality. The camera lens can be tilted on its axis via two adjustment screws on the mounting bracket. It can also be moved closer to or farther from the viewing window. 1.
en | Installation 3.6 Corner-mount No-grip Camera LED Adjustments (EX36N only) If you must make adjustments to the LEDs, follow the steps below. Refer to Figure 3.7 below for more details. Figure 3.7 LED Array Adjustments Number Description 1 LED Power Adjustment (VR1) 2 Photocell On/Off Adjustment (VR2) 3.6.1 Power Adjustments If you must adjust the power, follow these steps: 1. Ensure that the unit is “ON.” 2. Remove the rear cover for access to the LRB. 3.
Corner-mount No-grip Camera 3.7 Installation | en 17 Lens Replacement There is an extra 3.6 mm lens supplied with the unit and one extra focusing hex key. To replace the standard 2.5 mm lens with the supplied 3.6 mm replacement, follow the steps below: 1. 2. Open the front facia using the supplied hex key. Remove the camera sub-assembly from the housing. – For EX36MNXxxx models, use the supplied hex key to loosen the set screw that fixes the lens to its holder.
en | Installation 3.8 Corner-mount No-grip Camera Camera Re-assembly 1. Ensure that all wires are properly connected, that all holes are sealed against moisture penetration, and that all mounting screws are tight. 2. Slide the square foam pad over the camera’s lens. Ensure that the pad is as close to the faceplate viewing window as possible and the photocell is not covered by the foam pad. The foam pad is not symmetrical. Ensure that the LEDs are not covered when installing the pad. 3.
Corner-mount No-grip Camera Technical Information | en 4 Technical Information 4.1 Troubleshooting - Camera PROBLEM No video POSSIBLE CAUSE POSSIBLE SOLUTION Power supply: Check input power connections connections No video 19 at the terminal: – AC input wires to “AC IN” – DC input wires to “DC IN” Power supply: – Loose wires The supply range is: 12-28 VAC voltage range or 10.5 - 40 VDC for the camera section. Measure the voltage at the No video terminal block.
en | Technical Information Corner-mount No-grip Camera PROBLEM POSSIBLE CAUSE POSSIBLE SOLUTION Horizontal scan lines, Ground looping Check the coax cable shield is rolling up or down on video cable not touching ground (for Reversed video or Low voltage example, at couplings). Check voltage at input power faded image cable. Must be >10.5 VDC or >12 VAC for camera section. Check video leads for reversed connections. 4.
Corner-mount No-grip Camera 4.3 Technical Information | en 21 General Specifications CCD Sensor 1/3 in. - IR Optimized Video Signal Output 1 V p-p, 75 Ohm LED Type (EX36N only) High Perf. 850nm/940nm Operational -50 °C to +50 °C Temperature (-58 °F to 122 °F) Range Humidity Range Up to 85% (relative) Power Supply 24 VAC / 12 VDC (50/60 Hz), 11W Window Polycarbonate (1/4 in. LEXAN) Housing Steel, welded and powder coated Dimensions 8.3 in. (211 mm) W 6.0 in. (152 mm) D 5.5 in.
en | Technical Information F.01U.172.707 | 3.0 | 2011.02 Corner-mount No-grip Camera Instruction Manual Bosch Security Systems, Inc.
Bosch Security Systems, Inc. 850 Greenfield Road Lancaster, PA 17601 USA www.boschsecurity.us © Bosch Security Systems, Inc.