LTC 9365/00 Instruction Manual EN Wedge Housings
LTC 9365 | Instruction Manual | Important Safeguards EN | 2 Important Safeguards 1. Read, Follow, and Retain Instructions - All safety and operating instructions should be read and followed before operating the unit. Retain instructions for future reference. 2. Heed Warnings - Adhere to all warnings on the unit and in the operating instructions. 3. Attachments - Attachments not recommended by the product manufacturer should not be used, as they may cause hazards. 4.
EN | 3 LTC 9365 | Instruction Manual | Safety Precautions For Indoor Product 1. Water and Moisture - Do not use this unit near water - for example, in a wet basement, in an unprotected outdoor installation or in any area classified as a wet location. 2. Object and Liquid Entry - Never push objects of any kind into this unit through openings, as they may touch dangerous voltage points or short out parts that could result in a fire or electrical shock. Never spill liquid of any kind on the unit. 3.
EN | 4 LTC 9365 | Instruction Manual | Safety Precautions Sécurité Sicherheitshinweise ATTENTION : POUR ÉVITER TOUT RISQUE D'ÉLECTROCUTION, VORSICHT: UM EINEN ELEKTRISCHEN SCHLAG ZU N'ESSAYEZ PAS DE RETIRER LE CAPOT (OU LE PANNEAU VERMEIDEN, IST DIE ABDECKUNG (ODER RÜCKSEITE) NICHT ARRIÈRE). CET APPAREIL NE CONTIENT AUCUN COMPOSANT ZU ENTFERNEN. ES BEFINDEN SICH KEINE TEILE IN DIESEM SUSCEPTIBLE D'ÊTRE RÉPARÉ PAR L'UTILISATEUR.
LTC 9365 | Instruction Manual | Safety Precautions Sicurezza ATTENZIONE: PER RIDURRE IL RISCHIO DI SCOSSE ELETTRICHE NON RIMUOVERE LA COPERTURA (O IL PANNELLO POSTERIORE). L'UNITÀ NON CONTIENE COMPONENTI INTERNI RIPARABILI DALL'UTENTE. PER QUALSIASI INTERVENTO, RIVOLGERSI A PERSONALE TECNICO QUALIFICATO. Questo simbolo indica la presenza di "tensione pericolosa" non isolata all'interno del contenitore del prodotto. Ciò comporta un potenziale rischio di scosse elettriche.
LTC 9365 Series | Instruction Manual | Contents EN | 6 Table of Contents Important Safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 1 2 3 4 5 UNPACKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EN | 7 LTC 9365 Series | Instruction Manual | Unpacking 1 UNPACKING This electronic equipment should be unpacked and handled carefully. Check for the following items: • LTC 9365/00 Housing: 1 Housing Top 1 Housing Bottom • Hardware Kit: 1 Camera Bracket 2 1/4-20 x 5/8in. Bolts 2 Flat Washers 2 Split-ring Washers 1 1/4-20 x 3/8in. Bolt 1 O-ring 2 10-32 x 1/2in.
EN | 8 LTC 9365 Series | Instruction Manual | Installation Right Angle BNC Connector Knockouts Top Mount Figure 2 Housing Bottom 4. Remove the camera bracket by loosening the two (2) 1/4in. bolts on either side of the bracket. The nuts are held in place by the bracket, allowing for self-tightening when they are reinstalled. 5. Remove one of the three knockouts on the bottom of the housing (see Figure 2). This will allow electrical and video cables to pass through. 6.