Extractor hood [en] Instructions for installation and use
Ú Table of contents enalondusetifr]Insc[ n INSTRUCTION MANUAL ............................................................ 2 Environmental protection..............................................................2 Safety instructions................................................................. 2 Operating modes ................................................................... 4 Exhaust air mode...........................................................................4 Circulating-air mode ..........
In combination with an activated vapour extractor hood, room air is extracted from the kitchen and neighbouring rooms - a partial vacuum is produced if not enough fresh air is supplied. Toxic gases from the chimney or the extraction shaft are sucked backed into the living space. ■ ■ Adequate incoming air must therefore always be ensured. An incoming/exhaust air wall box alone will not ensure compliance with the limit.
Operating modes This appliance can be used in exhaust-air mode or circulatingair mode. ■ If the exhaust air is conveyed through the outer wall, a telescopic wall box should be used. Circulating-air mode Exhaust air mode The air which is drawn in is cleaned by the grease filters and an activated carbon filter and conveyed back into the kitchen. The air which is drawn in is cleaned by the grease filters and conveyed to the exterior by a pipe system.
Installing and removing filter ã=Risk of burns, risk of electric shock! With edge extraction from appliance. Always leave appliance to cool down before cleaning or servicing. Switch off fuse or pull out mains plug. 1. Pull metal-mesh grease filter downwards. Removing metal-mesh grease filter 2. Take metal-mesh grease filter out of the holder. In doing so, place other hand under the metal-mesh grease filter. Notes 1. Open lock and fold down the metal-mesh grease filter.
Replacing bulbs ã=Risk of burns, risk of electric shock! Replacing filament bulbs from defective bulbs. Switch off fuse or pull out mains plug. Always replace defective bulbs immediately (leave bulbs to cool down first) to prevent the remaining bulbs from overloading. Important! Use only bulb of the same type and same power (see bulb holder or rating plate inside the appliance) – to do this remove metal-mesh grease filter. 1. Lift bulb cover slightly and push towards the outside of the appliance. 2.
INSTALLATION INSTRUCTIONS Ins tallation in structio ns HOHFWUR JD] ! PP ! PP [ [ [ [ [ [ [ [ [ ■ ■ ■ [ This appliance is fitted to the kitchen ceiling or a stable suspended ceiling. Follow the enclosed installation instructions for additional special accessories (e.g. for circulating-air mode). The surfaces of the appliance are sensitive. Avoid damaging them during installation. Safety notes ã=Mortal danger, risk of intoxication! Due to combustion gases sucked back in.
Installation Pipe dimensions 5. Attach the upper part of the support frame to the ceiling with 4 screws. Note: The device manufacturer does not assume any warranty for complaints attributable to the pipe section. ■ ■ ■ The device achieves its optimum performance by means of a short, straight exhaust air pipe and as large a pipe diameter as possible. As a result of long rough exhaust air pipes, many pipe bends or diameters, the optimum extraction performance is not achieved and fan noise is increased.
Installing the appliance Electrical connection 1. Hook the appliance from below into the support frame. Note: Ensure that the mains cable is not trapped. 2. Attach the appliance to the support frame using 2 securing screws. ã=Risk of electric shock! from damaged connection cable. Do not kink or pinch connection cable during installation. The required connection data can be found on the rating plate inside the appliance; to do this, remove the metal-mesh grease filter.
Attaching flue duct ã=Risk of injury! From sharp edges during installation. Always wear protective gloves while installing the appliance. 1. Separate the flue ducts. To do this, remove the adhesive tape. 2. Remove the protective foil from both sides. 3. Attach both parts of the upper flue to the appliance and push together. Note: To prevent scratches, place paper for protection over the edges of the outer flue duct. 4. Push up the upper flue part and secure with 2 screws. 5.
'+= '+= '+= '+= '6= '6= '6= '6= 11
Robert Bosch Hausgeräte GmbH Carl-Wery-Straße 34 81739 München Germany www.bosch-home.