Dinion IP NWC-455-10P | NWC-455-20P en Operating Instructions
Dinion IP | en 3 Table of Contents 1 Introduction 15 1.1 Type number overview 16 1.2 Unpacking 16 1.3 System requirements 17 1.4 Overview of functions 17 1.4.1 Wide dynamic range 18 1.4.2 Power-over-Ethernet 18 1.4.3 Receiver 18 1.4.4 Video encoding 18 1.4.5 Tri Streaming 18 1.4.6 Recording 18 1.4.7 Multicast 19 1.4.8 Encryption 19 1.4.9 Configuration 19 1.4.10 Tampering recognition and motion detectors 19 1.4.11 Snapshots 19 1.4.12 Backup 19 1.4.
en | Dinion IP 4.2.2 Install menu 28 4.3 Adjustment procedure DC-iris Lens 28 4.4 Adjustment procedure Manual-iris Lens 29 4.5 Adjustment procedure Video-iris Lens 29 4.6 Install IP address submenu 29 4.7 Defaults 30 5 Network connection 31 5.1 System requirements 31 5.2 Establishing the connection 31 5.3 Secured network 33 6 Operation via the browser 34 6.1 Livepage 34 6.1.1 Processor load 34 6.1.2 Image selection 35 6.1.3 Digital I/O 35 6.1.
Dinion IP | en 5 7.4.1 Selecting an encoder profile 48 7.4.2 Changing profiles 50 7.4.3 JPEG posting 53 7.5 Camera settings 55 7.5.1 ALC 55 7.5.2 Enhance 56 7.5.3 Color 57 7.5.4 Installer options 58 7.6 Recording 58 7.6.1 Type 59 7.6.2 Storage information 59 7.7 iSCSI settings 60 7.7.1 iSCSI IP address 60 7.7.2 iSCSI LUN map 61 7.7.3 Target IP address 61 7.7.4 Target node 61 7.7.5 Target LUN 61 7.7.6 Target password 61 7.7.7 Initiator name 62 7.7.
en | Dinion IP 7.12.3 Motion detector 77 7.12.4 Sensitivity 78 7.12.5 Tamper detection 79 7.13 Alarm e-mail 81 7.13.1 Send alarm e-mail 81 7.13.2 Mail server IP address 81 7.13.3 Layout 82 7.13.4 Destination address 82 7.13.5 Sender name 82 7.13.6 Send e-mail for testing 82 7.14 Relay Settings 82 7.14.1 Alarm out 83 7.15 Service Settings 84 7.15.1 Network 84 7.15.2 Multicasting 87 7.15.3 Encryption 89 7.15.4 Version information 90 7.15.
Dinion IP | en 7 11 Troubleshooting 101 12 Specifications 103 12.1 Dimensions (mm/inch) 105 12.2 Accessories 106 12.2.1 Recommended lenses 106 12.2.2 Power transformers 106 13 Glossary 107 Bosch Security Systems Operating Instructions V 2.5 | 2007.
en | Dinion IP Important safety instructions Read, follow, and retain all of the following safety instructions. Heed all warnings on the unit and in the operating instructions before operating the unit. 1. Cleaning - Unplug the unit from the outlet before cleaning. Follow any instructions provided with the unit. Generally, using a dry cloth for cleaning is sufficient, but a moist flufffree cloth or leather shammy may also be used. Do not use liquid cleaners or aerosol cleaners. 2.
Dinion IP | en 9 230 VAC, 50 Hz, the input and output power cord must comply with the latest versions of IEC Publication 227 or IEC Publication 245. For outdoor use the power cord must comply to NEC400-4 (CEC Rule 4-010) and marked with OUTDOOR, W, or W-A. . 8. Power sources - Operate the unit only from the type of power source indicated on the label. Before proceeding, be sure to disconnect the power from the cable to be installed into the unit.
en | Dinion IP – – unit exhibits a distinct change in performance; unit does not operate normally when the user correctly follows the operating instructions. 11. Replacement parts - Be sure the service technician uses replacement parts specified by the manufacturer, or that have the same characteristics as the original parts. Unauthorized substitutions may cause fire, electrical shock, or other hazards. 12.
Dinion IP | en 11 DANGER! High risk: The lighting flash and arrowhead within the triangle is a warning sign alerting you of "Dangerous Voltage" inside the product that can cause an electrical shock, bodily injury, or death. ! ! i WARNING! Medium risk: The exclamation point within the triangle sign alerts the user to important instructions accompanying the unit. CAUTION! Alerts the user to the risk of damage to the unit. NOTE! General sign for notes. Calls attention to important information.
en | Dinion IP CAUTION! – Camera Grounding - For mounting the camera in potentially damp environments, ensure to ground the system using the ground connection of the power supply connector (see section: Connecting external power supply). – U.S.A. models only - Section 810 of the National Electrical Code, ANSI/NFPA No.
Dinion IP | en 13 FCC & ICES Information (U.S.A. and Canadian Models Only) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
en | Dinion IP Disposal Your Bosch product was developed and manufactured with high-quality material and components that can be recycled and reused. This symbol means that electronic and electrical appliances, which have reached the end of their working life, must be collected and disposed of separately from household waste material. Separate collecting systems are usually in place for disused electronic and electrical products.
Dinion IP 1 Introduction | en 15 Introduction The Dinion IP camera is a high-performance smart surveillance color camera. It incorporates advanced digital signal processing for outstanding picture performance. The camera operates as a network video server and transmits video and control signals over data networks such as Ethernet LANs and the Internet. The Dinion IP camera is easy to install and ready to use, and offers the best solution for demanding scene conditions.
en | Introduction 1.1 Dinion IP Type number overview Type number NWC-0455-10P NWC-0455-20P Standard 50 Hz 60 Hz Supply voltage 24 VAC or 12 VDC (use class 2 power supply) or PoE (IEEE 802.3af) CCD type 1/3" Table 1.1 Dinion IP type numbers 1.2 Unpacking Unpack carefully and handle the equipment with care.
Dinion IP 1.3 Introduction | en 17 System requirements – Computer with Windows 2000/XP operating system, network access and Microsoft Internet Explorer web browser version 6.0 or later or – Computer with Windows 2000/XP operating system, network access and reception software, for example VIDOS, BMVS or DIBOS 8.
en | Introduction Dinion IP achieved quickly and easily. Video images from a single camera can be simultaneously received on several receivers. 1.4.1 Wide dynamic range The digital signal is automatically processed in the camera to optimally capture the detail in both the high and low light areas of the scene simultaneously, maximizing the information visible in the picture. 1.4.2 Power-over-Ethernet Power for the camera can be supplied via a Power-over-Ethernet (IEEE 802.
Dinion IP 1.4.7 Introduction | en 19 Multicast In suitably configured networks, the multicast function enables simultaneous, real time transmission to multiple receivers. The prerequisite for this is that the UDP and IGMP V2 protocols are implemented on the network. 1.4.8 Encryption The data transmissions and the authentication channel can be encrypted to prevent unauthorized access. Web browser connections can be protected using HTTPS. 1.4.
en | Introduction 1.4.13 Dinion IP Intelligent Video Motion Detection The intelligent video motion detection (iVMD) system of the camera uses advanced analysis algorithms with comprehensive functions for the detection of motion. V 2.5 | 2007.
Dinion IP 2 Connections | en 21 Connections CAUTION! ! ! 2.1 Installation should only be performed by qualified service personnel in accordance with the National Electrical Code or applicable local codes. CAUTION! The camera module is a sensitive device and must be handled carefully. Do not drop when disassembling the unit. Power ! ! CAUTION! Ensure that your power supply matches the rated voltage of your camera before installing.
en | Connections 2.2 Dinion IP Network (and power) ! CAUTION! Never supply power via the Ethernet connection (PoE) when power is supplied via the power connector. - connect the camera to a 10/100 Base-T network. - use a shielded UTP Category 5 cable with RJ45 DC 12V AC 24V connectors. VIDEO ALARM - Power can be supplied to the camera via the Ethernet cable compliant with the Power-over-Ether- ETH UTP Cat 5 RJ45 net (IEEE 802.3af) standard. Fig. 2.
Dinion IP 2.4 Connections | en 23 Alarm connector - Max. wire diameter AWG 22-28 for both Pin Alarm socket 1 Ground - Default relay position n.o. (normally open), 2 Alarm in no alarm. 3 Relay out contact 1 - Alarm output relay switching capability: Max 4 Relay out contact 2 stranded and solid. voltage 30VAC or +40VDC. Max 0.5 A continuous, 10VA. - Alarm in: TTL logic, +5V nominal, +40VDC max, DC coupled with 22kOhm pull-up to Alarm +3.3V.
en | Mounting Dinion IP 3 Mounting 3.1 Lens mounting The camera accepts CS-mount lenses with a lens protrusion of up to 5mm. C-mount lenses can be mounted using the lens adapter ring. DC-iris lenses are recommended for the best picture performance. The camera automatically detects the type of lens used and optimizes performance accordingly. A spare male lens connector is provided.
Dinion IP 3.2 Mounting | en 25 Mounting the camera The camera can be mounted from the top or bottom. The bottom mounting is isolated from ground. With outdoor scenes, a DC-iris lens is recommended. ! CAUTION! Do not point the camera/lens into direct sunlight. Do not obstruct the free flow of air around the camera. NOTE! i The camera becomes quite warm when operating; this is normal. However, you should take this into account when touching the camera.
en | Quick set-up 4 Dinion IP Quick set-up The Dinion IP camera normally provides an optimal picture without the need for further adjustments. Configuration of the camera is carried out remotely via the network using a web browser. However, the camera also has an Installer menu in which basic installation settings (lens wizard, IP address) can be accessed. To view this menu connect a monitor to the composite video output of the camera. 4.
Dinion IP Quick set-up | en 27 Bosch 4. 4.2 Lock the back focus locking button. Accessing and navigating quick set-up menu Five keys, located behind the side panel, are used for navigating through the quick set-up menu. To access the set-up menus, press the menu/select key (center). The main menu appears on the monitor. Bos ch Bosch 4.2.
en | Quick set-up – Dinion IP Use the up or down keys to scroll up or down through a menu. – Use the left or right keys to move through options or to set parameters. – When in a menu, quickly pressing the menu/select key twice restores the selected item to its factory default. – To close all menus at once from any menu, select the Exit item and hold down the menu/select key until the menu display disappears. 4.2.
Dinion IP 4.4 Quick set-up | en 29 4. Turn the back focus adjustment as required. 5. Lock the back focus locking button. 6. Exit the menu. Adjustment procedure Manual-iris Lens 1. 4.5 Unlock the back focus locking button. 2. Adjust the lens to the maximum lens opening. 3. Turn the back focus adjustment as required. 4. Lock the back focus locking button. Adjustment procedure Video-iris Lens 1. Unlock the back focus locking button. 2. Access the Lens Wizard menu. 3.
en | Quick set-up Dinion IP Subnet Mask Enter the Subnet mask (default 255.255.255.0) Gateway Enter a Gateway address. Exit Return to the Install menu The new IP address, subnet mask and gateway address are set after you leave the menu. The camera reboots internally and the new values are set after a few seconds. 4.7 Defaults To restore all parameters (including IP address) to the factory defaults, press and hold the Up navigation key for at least 10 seconds and then confirm.
Dinion IP 5 Network connection | en 31 Network connection A computer with Microsoft Internet Explorer can be used to receive live images from the camera, control cameras and replay sequences stored on the local hard drive. The camera is configured over the network using the browser or via the Configuration Manager (supplied with the product). The configuration options using the menu system of the camera itself are limited to setting up the lens and network. NOTE! i 5.
en | Network connection Dinion IP Password protection in camera If the camera is password-protected, a message to enter the password appears. i NOTE! A camera offers you the option of limiting access across various authorization levels. 1. Enter the user name and the associated password in the appropriate fields. 2. Click OK. If the password is correct, the desired page is displayed. After a short time when the connection is established, the Livepage with the video image appears.
Dinion IP 5.3 Network connection | en 33 Secured network If a Radius server is used for network access control (802.1x authentication), the camera must be configured first. To configure the camera for a Radius network, connect it directly to a PC via a crossed network cable and configure the two parameters, identity and password. Only after these have been configured can you communicate with the camera via the network. Bosch Security Systems Operating Instructions V 2.5 | 2007.
en | Operation via the browser Dinion IP 6 Operation via the browser 6.1 Livepage After the connection is established, the Livepage is initially displayed. It shows the live video image on the right of the browser window. Depending on the configuration, various text overlays may be visible on the live video image. Other information may also be shown next to the live video image on the Livepage. The display depends on the settings on the Livepage configuration page. 6.1.
Dinion IP 6.1.2 Operation via the browser | en 35 Image selection You can view the image on a full screen. – Click one of the MPEG-4 Stream 1, MPEG-4 Stream 2 or MJPEG tabs below the video image to switch between the different displays for the camera image. 6.1.3 Digital I/O Depending on the configuration of the unit, the alarm input and the relay output are displayed next to the camera image.
en | Operation via the browser Dinion IP 1. Click the camera icon 2. The image is saved at a resolution of 704 × 576/480 pixels to save single images. (4CIF). The storage location depends on the configuration of the camera. 6.1.6 Recording video sequences Sections of the video sequence that is currently being shown on the Livepage can be saved on the computer's hard drive. The sequences are recorded at the resolution specified in the encoder configuration.
Dinion IP Operation via the browser | en 37 6. After a successful installation, two new icons for the Player and the Archive Player appear on the desktop. 7. 6.1.7 Double click the Player icon to start the Player. Running recording program The hard drive icon below the camera images on the Livepage changes during an automatic recording. The icon lights up and displays a moving graphic to indi- cate a running recording. If no recording is taking place, a gray icon is displayed. 6.
en | Operation via the browser Dinion IP . 6.2.1 Selecting recordings In the left section of the page, first select the partition whose recordings you want to view. All sequences that are saved in the partition are displayed in the list. A running number (track) is assigned to each sequence. Start time and stop time, recording duration, number of alarms, and recording type are displayed. 1. Click a partition name from the list to display the record- 2. Click a list entry.
Dinion IP Operation via the browser | en 39 means of click, the selected sequence is highlighted. The associated time interval is displayed in the bar in blue. A green arrow above the bar indicates the position of the image currently being played back within the sequence. The time bar offers various options for navigation in and between sequences. – You can change the time interval displayed by moving the blue area to the left or right while holding down the mouse button.
en | Operation via the browser Dinion IP recording speed, left indicates rewind, and right fast forward. The fast forward or rewind speed changes, depending on how far you move the slide control toward the runner icons. You can continuously select playback speed by means of the speed regulator: Red bars within the blue-gray sequence fields indicate the points in time where alarms were triggered. Drag the green arrow to navigate to these points quickly.
Dinion IP Configuration via the browser | en 41 7 Configuration via the browser 7.1 Settings When a connection is established, the Livepage is initially displayed. Click Settings in the application title bar to configure the camera and the application interface. A new page containing the configuration menu is opened. All settings are stored in the camera memory, and they are preserved even if the power is interrupted.
en | Configuration via the browser Dinion IP You can view the current settings by opening one of the configuration pages. 1. Click one of the menu options on the left of the window. The associated sub-menu is opened. 2. Click one of the links in the sub-menu. The corresponding page is opened. The settings are changed by entering new values or by selecting a pre-defined value in a list field.
Dinion IP Configuration via the browser | en 43 Click the Settings link at the top of the window to close the window without saving the changes made. 7.2 General Settings Various basic data for the camera can be set or selected here. 7.2.1 Camera identification Camera name The camera can be assigned a name to assist in identifying it. The name simplifies the management of multiple devices in more extensive systems, for example using the VIDOS or BVMS software.
en | Configuration via the browser 7.2.2 Dinion IP Password protection A camera is generally protected by a password to prevent unauthorized access to the unit. You can use various authorization levels (User name:) to limit access. NOTE! Proper password protection is only guaranteed if all i higher authorization levels are also protected with a password. For example, if a live password is assigned, a service and a user password should also be set.
Dinion IP Configuration via the browser | en 45 NOTE! The new password is then saved by clicking the Set i 7.2.3 button. You should therefore click the Set button immediately after entering and confirming the password, even if you also want to assign a password to another user name. Language selection Website language Select the language for the user interface here. 7.2.4 Date and time Date format Choose the desired date format here (Europe: DD.MM.YYYY; USA: MM.DD.YYYY; Japan: YYYY/MM/ DD).
en | Configuration via the browser 7.2.5 Dinion IP Time server The camera supports several network time server protocols and can synchronize its internal clocks with various types of time servers. The device calls up the time signal automatically once every minute. Unit time zone Select the time zone in which the system is located. Daylight saving time The internal clock can automatically switch between normal and daylight saving time (DST).
Dinion IP Configuration via the browser | en 47 9. When you are finished, click OK to save and activate the table. Time server IP address Enter the IP address of a time server. Time server type Choose the protocol used by the selected time server. It is recommended that you choose the SNTP server protocol. This protocol provides higher accuracy and is required for certain applications, as well as for future additions. Choose Time server, if the server uses RFC 868 as protocol. 7.3 Display Settings 7.
en | Configuration via the browser Dinion IP Alarm mode stamping Choose On if a text message should be overlaid in the event of an alarm. It can be displayed at a position of your choice using the Custom option. Or it can be set to Off if no overlay of this information is to be shown. 1. Select the desired position from the lists. – If you have selected the Custom option, additional fields are displayed to specify the exact position (Position (XY):). 2.
Dinion IP Configuration via the browser | en 49 structures). To do this, the camera simultaneously generates two data streams (Dual Streaming), for which you can select different compression settings, for example one setting for transmissions to the Internet and one for LAN connections. Pre-programmed profiles are available, which each give priority to different perspectives.
en | Configuration via the browser Dinion IP mation regarding data transmission are displayed and continually updated above the previews. 1. Click a tab to select the associated stream. 2. Select the desired setting from the list. NOTE! i Stream 2 is always transmitted for alarm connections and automatic connections. Take this into account when assigning the profile. Preview for Select which video data stream should be displayed in the previews.
Dinion IP Configuration via the browser | en 51 NOTE! The parameters as a group constitute a profile and are i dependent on one another. If you enter a setting outside the allowed range for a parameter, the nearest valid value is substituted when the settings are saved. Profile name You can enter a new name for the profile here. The name is then displayed in the list of available profiles in the Active encoder profile: field.
en | Configuration via the browser Dinion IP Default Click Default to return the profile to the factory default values. Details Click Details to display further settings for image quality and communication parameters. These settings require familiarity with MPEG and video encoding standards. Incorrect settings could result in useless video images. Max. data rate This maximum data rate is not exceeded under any circumstances.
Dinion IP Configuration via the browser | en 53 rate. A value of 31 results in a very high refresh rate and lower image quality. I-frame distance This parameter determines the number of inter-coded frames between two I-frames. 7.4.3 JPEG posting You can save individual JPEG images on an FTP server at certain intervals. You can then retrieve these images at a later date to reconstruct alarm events if required.
en | Configuration via the browser Dinion IP was stored on February 16, 2006 at 12.45 p.m. and 30 seconds. JPEG posting interval Enter the interval in seconds at which the images will be sent to an FTP server. Enter zero if you do not want any images to be sent. FTP server IP address Enter the IP address of the FTP server on which you wish to save the JPEG images. FTP server login Enter your login name for the FTP server. FTP server password Enter the password that gives you access to the FTP server.
Dinion IP 7.5 Configuration via the browser | en 55 Camera settings i 7.5.1 NOTE! If the camera is in monochrome mode, all color related menu items are disabled and cannot be accessed. ALC Video level Adjust the video output level (-15 to 0 to +15). Shutter – AES (auto-shutter) - the camera automatically sets the optimum shutter speed for manual iris lenses.
en | Configuration via the browser Dinion IP Gain When the Gain mode is On, the camera automatically sets the gain to the lowest possible value needed to maintain a good picture. NightSense™ Nightsense™ extends the low-light performance of the camera. – In AUTO mode, the camera automatically inches to monochrome in low-light conditions. – In FORCED mode, the camera remains in high-sensitivity monochrome operation. NOTE! i If NightSense™ is active, some noise or spots may appear in the picture.
Dinion IP 7.5.3 Configuration via the browser | en 57 Color White Balance – ATW: Auto tracking white balance allows the camera to constantly adjust for optimal color reproduction. – AWB HOLD: Puts the ATW on hold and saves the color settings. Red Gain Offset factory white point alignment (reducing red introduces more cyan). Blue Gain Offset factory white point alignment (reducing blue introduces more yellow). It is only necessary to change the white point offset for special scene conditions.
en | Configuration via the browser 7.5.4 Dinion IP Installer options Select the synchronization method for the camera: Internal for free running camera operation; Line Lock to lock to the power supply frequency. You can disable the buttons on the camera to prevent unauthorized change of the camera settings. – Click Restore all defaults to restore the factory defaults. – A confirmation screen appears. Allow 5 seconds for the camera to optimize the picture after a mode reset. 7.
Dinion IP 7.6.1 Configuration via the browser | en 59 Type Select the desired storage medium to subsequently configure the recording parameters. NOTE! i If you select VRM, the Video Recording Manager manages all recording and you are not able to make any further configurations via the web browser. CAUTION! ! 7.6.2 If you switch the storage medium from iSCSI server to RAM recording, the settings on the page iSCSI settings are lost and can only be restored by reconfiguring them.
en | Configuration via the browser 7.7 Dinion IP iSCSI settings If you select type iSCSI server as the storage medium, you then need to set up a connection to the desired iSCSI storage device and set the configuration parameters. NOTE! The storage device selected must adhere to the iSCSI i 7.7.1 specification, be available on the network and be completely set up. Amongst other things, it must have an IP address and be divided into logical drives (LUN). iSCSI IP address 1.
Dinion IP 7.7.2 Configuration via the browser | en 61 iSCSI LUN map The LUN map displays the logical drives configured for the iSCSI storage device. The current user is displayed for each drive. 1. Double-click a free drive (LUN). The associated information is called up and automatically displayed in the fields below the map. 2. If the logical drive is password protected, you must first enter the password in the Target password field and click the Set button.
en | Configuration via the browser 7.7.7 Dinion IP Initiator name The initiator name is automatically displayed after a connection has been established. 7.7.8 Initiator extension Enter the initiator extension. For the sake of clarity, you can enter a name or the existing extension with a comment, for example "– Camera 2". 7.7.9 Decoupling the drive used Each drive can only be associated with one user.
Dinion IP 7.8 Configuration via the browser | en 63 Partitioning A partition can be set up for recordings of the camera in a similar manner to the partitioning often found on computer hard drives. Parameters such as size, quality and type of video recording or compression standard used can be specified for the partition. Modifying these parameters leads to reorganization, during which stored data is lost. In addition, the page provides you with an overview of the drive data; for example total memory.
en | Configuration via the browser Dinion IP . 2. Read the information text in the upper section of the window. 3. Click in the text fields to enter values or use the other controls that are available, such as buttons, checkboxes or list fields. 4. Click Next>> in the lower section of the window to continue with the next step. 5. Click <
Dinion IP Configuration via the browser | en 65 2. Click Finish to complete the configuration. All settings are now transferred to the unit and subsequently become effective. 7.8.2 Partition status 1. Click Partition status. – A window opens showing information on the highlighted partition. This window provides information about the current configuration of the partition. No changes can be made here. 2. 7.8.3 Click OK to close the window.
en | Configuration via the browser 1. Dinion IP Click Edit partition. – A new window with the entries for the selected partition is opened. You can modify the configuration in the Partition properties window. 2. Enter the necessary changes. 3. Click Set to save the modifications. 4. After closing the window, click Set in the main window to transfer the changes to the unit and to save them. Type of recording Select the required recording type.
Dinion IP Configuration via the browser | en 67 The unit uses a special recording mode during alarm recording for optimal usage of storage capacity. As soon as a time gap for alarm recording begins, a recording is continuously made on one segment, which is the size of a complete alarm sequence (pre- and post-alarm time). This segment in the partition functions in a similar manner to a ring buffer and is overwritten until an alarm is actually triggered.
en | Configuration via the browser 7.8.4 Dinion IP Deleting partitions You can delete a partition at any time. CAUTION! Deleting a partition leads to the entire hard drive ! being reorganized and loss of all sequences stored on the drive. Consequently, you should check the recordings before deleting any partition and back up important sequences on the computer's hard drive. 1. Click Delete partition button to delete the highlighted partition.
Dinion IP Configuration via the browser | en 69 1. Click one of the tabs to edit the corresponding profile. 2. Click Default to return all settings to their defaults. 3. Click Copy settings if you want to copy the currently visible settings to another profile. A dialog appears and you can select the target profile for the copied settings. 4. Click Set in each profile tab that you want saved. Standard profile Select the encoder profile to use for continual recording.
en | Configuration via the browser Dinion IP Alarm track recording This parameter is only active, if the alarm tracks have been configured. – Click the checkbox to activate alarm track recording. The pre-alarm time gap is displayed automatically. Post-alarm time Select the post-alarm time gap from the list box. Post-alarm profile Select the encoder profile to use for recording during the postalarm time. The Standard profile option sets this to the same as the standard profile.
Dinion IP 7.10 Configuration via the browser | en 71 Recording scheduler Set all parameters for recording. Recording can be performed continuously or when an alarm occurs. . In the recording scheduler you can assign weekdays and times to the recording profiles you have created that define when alarms trigger recording. You can assign as many time periods (in 15-minute intervals) for any day of the week. When you move the mouse cursor over the table, the time is displayed.
en | Configuration via the browser 5. 6. Dinion IP Click Clear all to deselect all of the intervals. When you are finished, click Set to save the settings in the device. Holidays You can define holidays, which will override the settings for the normal weekly schedule. This allows you to apply the settings for Sundays to other days of the week. 1. Click the Holidays tab. Days that have already been defined are shown in the table. 2. Click Add. This opens a new window. 3.
Dinion IP Configuration via the browser | en 73 2. Click Stop to deactivate the recording schedule. Recordings that are currently running are interrupted and the configuration can be modified. 7.10.2 Recording status The graphic indicates the recording activity in this partition. You will see an animated graphic while recording is taking place. 7.11 Alarm Settings 7.11.1 Alarm in You can configure the possible alarm triggers for the camera.
en | Configuration via the browser 7.11.2 Dinion IP Alarm connections You can select the response of the camera when an alarm occurs. In case of an alarm, the camera can automatically establish a connection to a predefined IP address (compatible MPEG-4 compatible hardware receiver or computer with reception software). You can enter up to ten IP addresses which will be selected in order by the unit in case of an alarm until a connection is established.
Dinion IP Configuration via the browser | en 75 example when connections are initiated by a controlling system such as VIDOS or BVMS. The camera connects to all devices protected by the same general password. To define a general password: 1. Select 10 in the Number of Destination IP-address list box. 2. Enter 0.0.0.0 in the Destination IP-address field. 3. Enter the password in the Destination password field. 4. Set the user password of all the devices to be connected to this password.
en | Configuration via the browser 7.12 Dinion IP VCA The camera contains an integrated Video Content Analysis (VCA), which can detect and analyze changes in the signal. Such changes can be due to movements in the camera's field of view. You can configure the video content analysis for the camera. If necessary, click Default to return all settings to their default values. 7.12.1 Analysis Select the option On to activate the video content analysis.
Dinion IP Configuration via the browser | en 77 NOTE! i 7.12.2 On the Livepage configuration page, you can enable additional information overlays for the live video image too (see “Livepage configuration” on page 91). Analysis type Select the required analysis algorithm. By default, only Motion+ is available – this offers a motion detector and essential recognition of tampering. The current alarm status is displayed for information purposes. i 7.12.
en | Configuration via the browser 7.12.4 Dinion IP Sensitivity Sensitivity is available for the Motion+ analysis type. The basic sensitivity of the motion detector can be adjusted for the environmental conditions to which the camera is subject. The sensor reacts to variations in the brightness of the video image. The darker the observation area, the higher the value that must be selected. Min.
Dinion IP Configuration via the browser | en 79 4. If necessary, click Select all to select the entire video frame for monitoring. 5. Right-click any fields you wish to deactivate. 6. Click OK to save the configuration. 7. Click the close button (X) in the window title bar to close the window without saving the changes. 7.12.5 Tamper detection You can detect the tampering of cameras and video cables by means of various options.
en | Configuration via the browser Dinion IP objective) should trigger an alarm. The average brightness of the scene provides a basis for recognition. Scene too dark Activate this function if tampering associated with covering the objective (for instance, by spraying paint on it) should trigger an alarm. The average brightness of the scene provides a basis for recognition.
Dinion IP Configuration via the browser | en 81 1. Click Select area to configure the sensor fields. A new window will open. 2. If necessary, click Clear all first to clear the current selection (fields marked red). 3. Left-click the fields to be activated. Activated fields are marked red. 4. If necessary, click Select all to select the entire video frame for monitoring. 5. Right-click any fields you wish to deactivate. 6. Click OK to save the configuration. 7.
en | Configuration via the browser Dinion IP sent to the mail server via the address you entered. Otherwise leave the box blank (0.0.0.0). 7.13.3 Layout You can select the data format of the alarm message. – Standard (with JPEG): e-mail with JPEG image file attachment. – SMS: e-mail in SMS format to an e-mail-to-SMS gateway (for example to send an alarm by cellphone) without an image attachment.
Dinion IP 7.14.1 Configuration via the browser | en 83 Alarm out Select the event that will trigger the alarm output; – an internal motion detection/VCA, – an internal day/night switching, or – an external trigger from the network. For example, it is possible to switch on a spotlight in response to a motion alarm and switch it off again when the alarm is over. Relay name The relay can be assigned a name here. The name is shown on the button next to Trigger relay.
en | Configuration via the browser 7.15 Service Settings 7.15.1 Network Dinion IP The settings on this page are used to integrate the unit into an existing network. NOTE! i Changes to the IP address, subnet mask or gateway address are transferred to the unit by clicking Set. However, they do not become active until the device is restarted. – Click Set after entering a new IP address. – To do this, enter the old IP address followed by / reset (for instance 192.168.0.
Dinion IP Configuration via the browser | en 85 restarted it can only be accessed at the new IP address. IP address Enter the desired IP address for the camera in this field. The IP address must be valid for the network. Subnet mask Enter the appropriate subnet mask for the set IP address here. Gateway address If you want the unit to establish a connection to a remote location in a different subnet, enter the IP address of the gateway here. Otherwise, this field can remain empty (0.0.0.0).
en | Configuration via the browser Dinion IP If you want to limit connections to SSL encryption, you must set the Off option in the HTTP browser port, the RCP+ port, and Telnet support. This deactivates all unencrypted connections allowing connections on the HTTPS port only. NOTE! i You can configure and activate encryption for media data (video, audio, metadata) on the Encryption page (see “Encryption” on page 89). RCP+ port 1756 Activating RCP+ port 1756 allows unencrypted connections on this port.
Dinion IP Configuration via the browser | en 87 nents and can send SNMP messages (traps) to IP addresses. It supports SNMP MIB II in the unified code. If you wish to send SNMP traps, enter the IP addresses of one or two required target devices here. To choose which traps are sent: 1. Click Select. A dialog box appears. 2. Click the check boxes of the appropriate traps. 3. Click OK to close the window and send all of the checked traps.
en | Configuration via the browser Dinion IP to receive the video signal from an encoder simultaneously. This is either done by duplicating the data stream in the unit and then distributing it to multiple receivers (multi-unicast) or by distributing an individual data stream in the network itself to multiple receivers in a defined group (multicast). You can enter a dedicated multicast address and port for each stream. You can switch between the streams by clicking the associated tabs.
Dinion IP Configuration via the browser | en 89 Port If there are simultaneous data streams at the same multicast address, you must assign different ports to each data stream. Enter the port address for the relevant stream here. Streaming Click in the checkbox to activate multicast streaming mode for the relevant stream. An activated stream is marked with a check. Multicast packet TTL A value can be entered to specify how long the multicast data packets are active on the network.
en | Configuration via the browser Dinion IP 5. Click Generate keys to generate new keys for marked 6. Click Edit to enter a key for a marked entry manually. streams. Automatic key exchange: Mark this checkbox to activate an automatic key exchange between two devices (or the camera and a software decoder) across an encrypted connection. 7.15.4 Version information This window is for information only and cannot be modified. Keep this information at hand when seeking technical support.
Dinion IP 7.15.5 Configuration via the browser | en 91 Livepage configuration In this window, you can adapt the appearance of the Livepage to meet your requirements. Options are provided here to display various information and operating elements in addition to the video image. Moreover, individual background graphics can be used for the main window and the upper area of the window (banners). NOTE! Either GIF or JPEG images can be used.
en | Configuration via the browser Dinion IP Logo URL Enter the path to a suitable background graphic in this field. The image can be stored on a local computer, a local network or at an Internet address. – Click Search if necessary to find a suitable image on the local network. Device logo URL Enter the path for a suitable image for the upper part of the window (banner) here. The image can be stored on a local computer, a local network or at an Internet address.
Dinion IP Configuration via the browser | en 93 Show system log The system messages are displayed with the date and time in a field next to the video image and provide information about the establishment and termination of connections etc. Save event log Select this option to save event messages in a text file on the local computer. This file can be viewed, edited and printed with any text editor or the standard Office software.
en | Configuration via the browser i 7.15.7 Dinion IP NOTE! The activation key cannot be deactivated again and is not transferable to other units. Maintenance CAUTION! Before starting the firmware update, make sure that ! you have selected the correct upload file! Uploading the wrong files can result in the unit no longer being addressable, requiring it to be replaced.
Dinion IP Configuration via the browser | en 95 NOTE! A firmware update resets all camera parameters to their i factory default values. If you wish to retain the old values first save the configuration by performing a configuration download. After the firmware update you can reload your parameter values by performing a configuration upload. To update the firmware: 1. First, save the update file to the hard disk. 2. Enter the full path for the update file in the field or click Browse...
en | Configuration via the browser Dinion IP Configuration upload 1. Enter the full path of the file to upload or click Browse... to select the desired file. 2. Make certain that the file to be loaded comes from the same device type as the unit you want to reconfigure. 3. Click Upload to begin transmission to the unit. The progress bar allows you to monitor the transfer. Once the upload is complete, the new configuration is activated.
Dinion IP 8 Connections between video servers | en 97 Connections between video servers A camera can be used as a transmitter and a compatible MPEG4 hardware decoder with a connected monitor as a receiver using an Ethernet network connection. This way it is possible to cover large distances with little effort for installation or cabling. 8.0.1 Installation Cameras are designed to connect with other VIP devices automatically with the corresponding configuration.
en | Connections between video servers 8.0.4 Dinion IP Connecting with a Web browser Various requirements must be met in order to operate using a Web program. i NOTE! Transmitter and receiver must be located in the same subnet to establish a hardware connection with a Web browser. 1. Use the Web browser to connect to the receiver. Its home page is displayed. Under Video sources on the page Connections, select the camera. A JPEG snapshot of the selected video source is displayed on the page. 2.
Dinion IP 9 Operation with decoder software | en 99 Operation with decoder software VIDOS The camera video server and VIDOS software combine to provide a high-performance system solution. VIDOS is software for operating, controlling and administering CCTV installations (such as surveillance systems) at remote locations. It runs under Microsoft Windows operating systems. Its main job is decoding video, audio and control data from a remote transmitter.
en | Maintenance Dinion IP 10 Maintenance 10.1 Testing the network connection The ping command can be used to check the connection between two IP addresses. This allows you to test whether a device is active in the network. 1. Open the DOS command prompt. 2. Type ping followed by the IP address of the device. If the device is found, the response appears as " Reply from ... ", followed by the number of bytes sent and the transmission time in milliseconds.
Dinion IP 11 Troubleshooting | en 101 Troubleshooting If you cannot resolve a fault, please contact your supplier or system integrator or go direct to Bosch Security Systems Customer Service. The version numbers of the internal processors can be viewed on a special page. Please note this information before contacting Customer Service. 1. In the address bar of your browser, after the unit IP address enter /version (for example 192.168.0.80/version). 2. Write down the information or print out the page.
en | Troubleshooting Malfunction Dinion IP Possible causes Solution The unit does not Alarm source is not Select possible alarm sources on report an alarm. selected. the Alarm sources configuration page. No alarm response speci- Specify the desired alarm fied. response on the Alarm connec- tions configuration page, if necessary change the IP address. The unit is not opera- Power failure during protional after firmware Have the unit checked by Cus- gramming by the update file.
Dinion IP 12 Specifications | en 103 Specifications Type number NWC-0495-10P NWC-0495-20P Standard PAL NTSC Active pixels 752x582 768x492 Rated supply voltage 24 VAC or 12 VDC or Power-over-Ethernet (IEEE 802.3af) 12-28 VAC (50/60 Hz) 11-36 VDC Min illumination < 0.4 lux Imager Interline CCD Resolution 540 TVL (BNC) < 0.
en | Specifications Dinion IP Image resolutions 704 × 576/480 pixels (D1/4CIF) (PAL/NTSC) 464 × 576/480 pixels (2/3 D1) 704 × 288/240 pixels (2CIF) 704 × 288/240 pixels (1/2 D1) 352 × 288/240 pixels (CIF) 176 × 144/120 pixels (QCIF) Total delay 120 ms (PAL/NTSC, MPEG-4, no network delay) Image refresh rate 1 ... 50/60 fields/s adjustable (PAL/NTSC) Field/image-based coding Network protocols V 2.5 | 2007.
Dinion IP 12.1 Specifications | en 105 Dimensions (mm/inch) 118 (4.646") 85 (3.346") 34 (1.339") 1/4"-20 UNC 1/4"-20 UNC 48 (1.889") 123 (4.843") 59 (2.323") 67 (2.638") Dimensions in mm (inches). Bosch Security Systems Operating Instructions V 2.5 | 2007.
en | Specifications 12.2 12.2.1 Dinion IP Accessories Recommended lenses LTC 3764/20 Varifocal Lens – 1/2-inch, 4 -12 mm, DC-iris, C-mount, F/1.2-360, 4 pin LTC 3774/30 Varifocal Lens – 1/2-inch, 10 - 40 mm, DC-iris, C-mount, F/1.4-360, 4-pin LTC 3783/50 Zoom Lens – 1/2-inch, 8.5 - 85 mm, video-iris, C-mount F/1.6-360, 4-pin LTC 3793/50 Zoom Lens – 1/2-inch, 8 - 144 mm, video-iris, C-mount, F/1.6-360, 4-pin LTC 3664/40 Varifocal Lens – 1/3-inch, 2.8 - 11 mm, DC-iris, CS-mount F/1.
Dinion IP 13 Glossary | en 107 Glossary Brief explanations of some of the terms and abbreviations found in this user guide are given below. 10/100 Base-T 802.1x IEEE 802.3 specification for 10 or 100 MBit/s Ethernet The IEEE standard, 802.1x, provides a general method of access control and authorization for IEEE 802-based networks.
en | Glossary Dinion IP IP See Internet Protocol IP address A 4-byte number uniquely defining each device on the Internet. It is usually written in dotted decimal notation with full stops separating the bytes, for example "209.130.2.193".
Dinion IP Glossary | en 109 RS232/RS422/RS485 Standards for serial data transmission RTP Realtime Transport Protocol; A transmission protocol for real-time video and audio SNTP Simple Network Time Protocol is a simplified version of NTP SSL Secure Sockets Layer is an encryption protocol for data (see NTP). transmission in IP-based networks.
Bosch Security Systems Robert-Koch-Straße 100 D-85521 Ottobrunn Germany Telefon 089 6290-0 Fax 089 6290-1020 www.boschsecuritysystems.
