DIVAR IP 7000 2U DIP-7080-00N, DIP-7082-8HD, DIP-7083-8HD en Quick Installation Guide
DIVAR IP 7000 2U Table of Contents | en 3 Table of contents 1 Safety precautions 4 1.1 General safety precautions 4 1.2 Electrical safety precautions 5 1.3 ESD precautions 6 1.4 Operating precautions 6 1.5 Important notices 7 1.6 FCC and ICES compliance 7 2 System overview 3 System setup - hardware 10 3.1 Introduction 10 3.2 Unpacking the system 10 3.3 Preparing for setup 10 3.3.1 Choosing a setup location 10 3.3.2 Rack precautions 11 3.3.
en | Safety precautions DIVAR IP 7000 2U Safety precautions 1 Observe the safety precautions in this chapter. 1.1 General safety precautions Follow these rules to ensure general safety: – Keep the area around the system clean and free of clutter. – Place the chassis top cover and any system components that have been removed away from the system or on a table so that they won't accidentally be stepped on.
DIVAR IP 7000 2U Safety precautions | en 5 Warning! Lithium battery: Batteries that have been inserted wrongly can cause an explosion. Always replace empty ! batteries with batteries of the same type or a similar type recommended by the manufacturer. Handle used batteries carefully. Do not damage the battery in any way. A damaged battery may release hazardous materials into the environment. Dispose of empty batteries according to the manufacturer's instructions.
en | Safety precautions – DIVAR IP 7000 2U Use only one hand when working with powered-on electrical equipment. This is to avoid making a complete circuit, which will cause electrical shock. Use extreme caution when using metal tools, which can easily damage any electrical components or circuit boards they come into contact with. – The power supply power cords must include a grounding plug and must be plugged into grounded electrical outlets. The unit has more than one power supply cord.
DIVAR IP 7000 2U Safety precautions | en 7 Note: Please handle used batteries carefully. Do not damage the battery in any way. A damaged battery may release hazardous materials into the environment. Do not discard a used battery in the garbage or a public landfill. Please comply with the regulations set up by your local hazardous waste management agency to dispose of your used battery properly. 1.5 Important notices Accessories - Do not place this unit on an unstable stand, tripod, bracket, or mount.
en | System overview 2 DIVAR IP 7000 2U System overview DIVAR IP 7000 is an affordable, simple and reliable all-in-one recording, viewing and management solution for network surveillance systems of up to 64 channels (with 32 channels pre-licensed).
DIVAR IP 7000 2U System overview | en 9 Rear view: 2 1 1 3 4 5 2x mains connection 100 – 240 VAC, 7 6 5 50 - 60 Hz Monitor (VGA) Note: Do not use! 2 2x PS/2 (mouse and keyboard) 6 2x NIC 3 2x USB 7 Slots for: 4 Serial interface COM1 – 1x graphic card (1x Display Port, 1x DVI) – DVI port must be used for configuration Bosch Sicherheitssysteme GmbH Quick Installation Guide – 1x sound card – 2x USB 2.0 2014.
en | System setup - hardware DIVAR IP 7000 2U 3 System setup - hardware 3.1 Introduction Scope of delivery: – DIVAR IP 7000 – 8-bay system, fully equipped with 8 hard drives (DIP-7082-8HD) – In addition to the system itself, the following items should have been shipped along with each system 3.
DIVAR IP 7000 2U 3.3.2 System setup - hardware | en 11 Rack precautions Warning! ! To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety: – Ensure that the leveling jacks on the bottom of the rack are fully extended to the floor with the full weight of the rack resting on them. – In single rack installations, attach stabilizers to the rack.
en | System setup - hardware DIVAR IP 7000 2U Circuit overloading Consideration should be given to the connection of the equipment to the power supply circuitry and the effect that any possible overloading of circuits might have on overcurrent protection and power supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern. Reliable ground A reliable ground must be maintained at all times. To ensure this, the rack itself should be grounded.
DIVAR IP 7000 2U 3.4.2 System setup - hardware | en 3. Press the quick-release tab. 4. Separate the inner rail extension from the outer rail assembly. 13 Installing the inner rails The chassis includes a set of inner rails in two sections: inner rails and inner rail extensions. The inner rails are pre-attached to the chassis, and do not interfere with normal use of the chassis if you decide not to use a server rack.
en | System setup - hardware 3.4.3 DIVAR IP 7000 2U Installing the outer rails to the rack Outer rails attach to the rack and hold the chassis in place. The outer rails extend between 30 inches and 33 inches. 3 1 2 To install the outer rails to the rack: 1. Secure the back end of the outer rail to the rack, using the screws provided. 2. Press the button where the two outer rails are joined to retract the smaller outer rail. 3.
DIVAR IP 7000 2U System setup - hardware | en 15 Warning! ! Do not pick up the unit with the front handles. The handles are designed to pull the system from a rack only. Warning! Stability hazard ! Before sliding the unit out for servicing make sure that the rack stabilizing mechanism is in place, or the rack is bolted to the floor. Failure to stabilize the rack can cause the rack to tip over. See also: Rack precautions, page 11 3.4.
en | System setup - first steps 4 DIVAR IP 7000 2U System setup - first steps The following installation directive provides information on Installation and Configuration. DIVAR IP systems are based on Windows Server 2008 R2 operating system. This chapter is valid for DIVAR IP models that come with pre-installed hard drives. Empty units start into the DOM recovery menu on first start. The recovery process and the RAID setup are described in the installation manual.
DIVAR IP 7000 2U System setup - first steps | en 17 5. Accept the license terms, then click Start. Windows restarts. 6. After restart is finished, press CTR+ALT+DELETE. The Windows logon page is displayed. 7. Enter the default password WSS4Bosch. 8. After entering the password, a message is displayed that you must change the password before logging on the first time. To confirm, click OK. 9. Change the password. A series of scripts perform important setup tasks. This can take several minutes.
en | System setup - first steps DIVAR IP 7000 2U – adding additional license packages – adjusting schedules – configuring systems with no or multiple VRM – configuring external storage devices – adding Video Streaming Gateway – all advanced configurations beyond a basic setup (maps or alarms, for example) For these tasks refer to the Bosch VMS manual (see Additional documentation and client software, page 31). To achieve a quick configuration using the Configuration Wizard: 1.
DIVAR IP 7000 2U System setup - first steps | en 19 Network settings page You configure the network settings of the operating system. As soon as you click Next button, the settings are activated. If you have changed any setting on this page, click Reboot to restart the system. Notice! If a DHCP server is employed in the network for the dynamic assignment of IP addresses, activate acceptance of IP addresses automatically assigned to the device.
en | System setup - first steps DIVAR IP 7000 2U Time settings page You configure the time settings of the operating system. Note: We highly recommend defining a time server in a video surveillance environment. 2014.
DIVAR IP 7000 2U System setup - first steps | en 21 Video settings page This page displays the devices and services that are included in the latest saved configuration. You can import a configuration. Note: If the wizard fails in this step, close the wizard and start it again. Bosch Sicherheitssysteme GmbH Quick Installation Guide 2014.
en | System setup - first steps DIVAR IP 7000 2U Device selection page Note: The scan for devices can take a time. You can cancel the scan. All devices that were already scanned, are displayed in the table. This page displays all video devices that are not included in the latest saved configuration. Deselect the devices that should not be added to the configuration, then click Next. 2014.
DIVAR IP 7000 2U System setup - first steps | en 23 Device authentication page This page is used to authenticate at video devices protected by password. For easy authentication with the same password for multiple devices you can use the clipboard (CTRL +C, CTRL+V): 4 Select a row with a successfully authenticated device (green lock is displayed), press CTRL+C, select multiple rows displaying a red lock and press CTRL+V).
en | System setup - first steps DIVAR IP 7000 2U Recording profile page For different profile assignments to different cameras you must execute Configuration Wizard multiple times. Note: Before selecting a recording profile observe the following: – Recording profile details All video devices use the default recording profile details. To change these use the Bosch VMS Configuration Client. – Stream quality settings All video devices use the default settings for Stream 1 to record.
DIVAR IP 7000 2U System setup - first steps | en 25 The default schedule is used for all recording profiles. The Day schedule is active from 8 a.m. until 6 p.m., Monday through Friday. The Night schedule is active from 6 p.m. until 8 a.m., Monday through Friday. The Weekend schedule is active 24 hours a day for Saturday and Sunday. To change the schedule use the Bosch VMS Configuration Client. Bosch Sicherheitssysteme GmbH Quick Installation Guide 2014.
en | System setup - first steps DIVAR IP 7000 2U Add storage page This page allows the addition of additional iSCSI storage devices For limitations, refer to the datasheet available in the online catalog. Notice! If the wizard stops and the message appears, that the internal iSCSI storage is not ready for recording because the LUNs are not formatted, you must format the LUNs using Bosch VMS Configuration Client. To format the LUNs, see Bosch VMS Configuration Manual, Chapter Formatting a LUN. 2014.
DIVAR IP 7000 2U System setup - first steps | en 27 User accounts page You can add users and passwords. Use Configuration Client to add user groups and to change permissions. Notice! We strongly recommend using password protection for all users defined in the system. Bosch Sicherheitssysteme GmbH Quick Installation Guide 2014.
en | System setup - first steps DIVAR IP 7000 2U Finish configuration page This page is used for providing a global default password for all devices that are not currently protected by a password. After clicking Save and activate the configuration is activated. After successful activation the Activate Configuration page is displayed again. Now you can store a backup of the configuration if desired: Click Save backup copy.
DIVAR IP 7000 2U System setup - first steps | en 29 Note: It is also possible to configure the devices individually with specific IP addresses based on MAC address. 5. Enter the starting IP address for the address range you want to use, click the Calculate 6. To restart the devices, click OK. 7. Close Configuration Client . tab, then click OK. 4.5.2 Adding additional licenses You can add additional licenses using Configuration Client. To activate the software: 1. 2. Start Configuration Client.
en | System setup - first steps DIVAR IP 7000 2U To verify playback functionality in the Operator Client 4 The time line moves if the a camera is viewed in playback mode. To perform further functionalities refer to the Bosch VMS manual. Performance overview live 4CIF Number of software 2.5 Mbit 5 Mbit 10 Mbit 20 13 9 monitors 720p Number of software 2.5 Mbit 5 Mbit 10 Mbit 14 11 6 monitors 1080p Number of software 2.
DIVAR IP 7000 2U 5 Additional documentation and client software | en 31 Additional documentation and client software Documentation for Bosch Security System products can be found as follows: 4 www.boschsecurity.com > select your region and your country > select Product Catalog > start a search for your product > select the product in the search results to show the existing documents.
Bosch Sicherheitssysteme GmbH Robert-Bosch-Ring 5 85630 Grasbrunn Germany www.boschsecurity.
