DIVAR IP 3000 DIP-3040-00N, DIP-3042-2HD, DIP-3042-4HD en Quick Installation Guide
DIVAR IP 3000 Table of Contents | en 3 Table of contents 1 Safety precautions 4 1.1 General safety precautions 4 1.2 Electrical safety precautions 7 1.3 ESD precautions 8 1.4 Operating precautions 2 System overview 10 2.1 Device views 11 2.2 LED description - front panel 13 2.3 LAN port LED description - rear panel 14 3 System setup - first steps 16 3.1 Introduction 16 3.2 Setup instruction 16 3.3 Starting the application 17 3.
en | Safety precautions DIVAR IP 3000 Safety precautions 1 Observe the safety precautions in this chapter. 1.1 General safety precautions Follow these rules to ensure general safety: – Keep the area around the system clean and free of clutter. – Place the chassis top cover and any system components that have been removed away from the system or on a table so that they won't accidentally be stepped on.
DIVAR IP 3000 Safety precautions | en 5 Warning! Removing the housing: To avoid electric shock, the housing must only be removed by qualified service personnel. ! Before removing the housing, the plug must always be removed from the mains socket and remain disconnected while the housing is removed. Servicing must only be carried out by qualified service personnel. The user must not carry out any repairs.
en | Safety precautions DIVAR IP 3000 Warning! ! Handling of lead solder materials used in this product may expose you to lead, a chemical known to the State of California to cause birth defects and other reproductive harm. Notice! Electrostatically sensitive device: To avoid electrostatic discharges, the CMOS/MOSFET protection measures must be carried out correctly.
DIVAR IP 3000 1.2 Safety precautions | en 7 Electrical safety precautions Basic electrical safety precautions should be followed to protect you from harm and the system from damage: – Be aware of the locations of the power on/off switch on the chassis as well as the room's emergency power-off switch, disconnection switch or electrical outlet. If an electrical accident occurs, you can then quickly remove power from the system.
en | Safety precautions DIVAR IP 3000 new fuse must be the same or equivalent as the one replaced. Contact technical support for details and support. Caution! Mainboard Battery: There is a danger of explosion if the onboard battery is installed upside down, which will reverse its ! polarities. This battery must be replaced only with the same or an equivalent type recommended by the manufacturer (CR2032). Dispose of used batteries according to the manufacturer's instructions. 1.
DIVAR IP 3000 – Safety precautions | en 9 Handle a board by its edges only. Do not touch its components, peripheral chips, memory modules or contacts. – When handling chips or modules, avoid touching their pins. – Put the mainboard and peripherals back into their antistatic bags when not in use. – For grounding purposes, make sure your computer chassis provides excellent conductivity between the power supply, the case, the mounting fasteners and the mainboard. 1.
2 en | System overview DIVAR IP 3000 System overview The DIVAR IP 3000 system is an affordable and easy to use all-inone recording, viewing, and management solution for network surveillance systems of up to 32 channels. All channels are prelicensed.
DIVAR IP 3000 2.1 System overview | en 11 Device views There are several LEDs on the front and rear of the chassis. The LEDs show the over-all status of the system and the activity and health of specific components. Front view: 1 6 2 3 4 5 1 Lock for front cover 4 LAN activity LED 2 Power on/off LED 5 System status LED 3 Hard disk access LED 6 Individual hard disk LED Bosch Sicherheitssysteme GmbH 2013.
en | System overview DIVAR IP 3000 Rear view: 1 1 2 1x VGA (monitor) 3 5 5 4 6 7 Mains connection 100 240 VAC 2 1x Ethernet (RJ45) 6 1x USB 3.0 Note: Do not use this port for keyboard and mouse. 3 4x USB 2.0 7 1x DVI (monitor), for local Note: Use these ports for viewing keyboard and mouse Note: connection. 2013.
DIVAR IP 3000 System overview | en 4 1x eSATA for data export Note: Do not connect hard disk drives for 13 If the system is only connected to the DVI port, no video signal is displayed until the system recording. has started completely. This can take 1 – 2 minutes. A video signal is always displayed when the monitor is connected to the VGA port. 2.2 LED description - front panel This chapter describes the LED displays on the front of the chassis.
en | System overview DIVAR IP 3000 LED LED LED indicator color state Blue Blinking Description System is booting or shutting down Red On Critical event occurred, such as degraded RAID volume. Bosch also provides the API and then application program is able to control this status. Individual N/A hard disk LED Off Hard drive not present. (default) Blue On Hard drive present. Red On Bosch provides the API to let application program to control this status. 2.
DIVAR IP 3000 System overview | en Nr. 1 LED LED LED indicator color state RJ45 LED N/A Off (left) 2 RJ45 LED (right) 15 NIC state No connection or 10 Mb/s Green On 100 Mb/s Yellow On 1000 Mb/s Yellow On Active connection Yellow Blinking Transmit or receive activity Bosch Sicherheitssysteme GmbH 2013.
3 en | System setup - first steps DIVAR IP 3000 System setup - first steps The following installation directive provides information on Installation and Configuration. DIVAR IP systems are based on Windows Storage Server 2008 R2 operating system. This chapter is valid for DIVAR IP models that come with preinstalled hard drives. Empty units start into the DOM recovery menu on first start. The recovery process is described in the installation manual. See also: – 3.
DIVAR IP 3000 System setup - first steps | en 17 User with administrator rights: – User: BVRAdmin – Password: WSS4Bosch Notice! We strongly recommended not changing the user settings. Changing the user settings can result in malfunctioning of the system. 3.3 Starting the application DIVAR IP system is ready to go out of the box. The application provides a simple to install and intuitive to use solution for network surveillance systems. To start the application: 1.
en | System setup - first steps DIVAR IP 3000 A series of scripts perform important setup tasks. This can take several minutes. Do not turn off the computer. A page is displayed where you can perform initial Windows configuration tasks. Note: In case of password loss a system recovery must be performed as described in the installation manual. The configuration must be done from scratch or must be imported. 10.
DIVAR IP 3000 3.4 System setup - first steps | en – Using Bosch VMS Configuration Client, page 30 – Additional Documentation and client software, page 33 19 Using Bosch VMS Configuration Wizard Intended use for Configuration Wizard is the quick and easy configuration of a smaller system. Configuration Wizard helps you to achieve a configured system including VRM, iSCSI system, cameras, recording profiles and user groups. User groups and their permissions are configured automatically.
en | System setup - first steps DIVAR IP 3000 Welcome page If the connection to the Management Server cannot be established, a corresponding error message is displayed. You cannot continue working with Configuration Wizard. If VRM is not available on the computer, a corresponding error message is displayed. You cannot continue working with Configuration Wizard. If the license check fails, a corresponding error message is displayed. You cannot continue working with Configuration Wizard. 2013.
DIVAR IP 3000 System setup - first steps | en 21 Network settings page You configure the network settings of the operating system. As soon as you click Next button, the settings are activated. If you have changed any setting on this page, click Reboot to restart the system. Notice! If a DHCP server is employed in the network for the dynamic assignment of IP addresses, activate acceptance of IP addresses automatically assigned to the device.
en | System setup - first steps DIVAR IP 3000 Time settings page You configure the time settings of the operating system. 2013.
DIVAR IP 3000 System setup - first steps | en 23 Video settings page This page displays the devices and services that are included in the latest saved configuration. You can import a configuration. Bosch Sicherheitssysteme GmbH 2013.
en | System setup - first steps DIVAR IP 3000 Device selection page This page displays all video devices that are not included in the latest saved configuration. Deselect the devices that should not be added to the configuration, then click Next. 2013.
DIVAR IP 3000 System setup - first steps | en 25 Device passwords page This page is used to authenticate password protected devices. This can either be done for all cameras at once (if passwords are identical) or for each camera individually. Configuration Client must be used in order to set or change device passwords. Password check is performed automatically, when you do not enter a character in a password field for a few seconds or you click outside the password field.
en | System setup - first steps DIVAR IP 3000 Recording profile page For different profile assignments to different cameras you must execute Configuration Wizard multiple times. Note: Before selecting a recording profile observe the following: – Recording profile details All video devices use the default recording profile details. To change these use the Bosch VMS Configuration Client. – 2013.
DIVAR IP 3000 System setup - first steps | en 27 All video devices use the default settings for Stream 1 to record. To change these use the Bosch VMS Configuration Client. – Schedule The default schedule is used for all recording profiles. The Day schedule is active from 8 a.m. until 6 p.m., Monday through Friday. The Night schedule is active from 6 p.m. until 8 a.m., Monday through Friday. The Weekend schedule is active 24 hours a day for Saturday and Sunday.
en | System setup - first steps DIVAR IP 3000 Add storage page This page allows the addition of additional iSCSI storage devices For limitations, refer to the datasheet available in the online catalog. Notice! If the wizard stops and the message appears, that the internal iSCSI storage is not ready for recording because the LUNs are not formatted, you must format the LUNs using Bosch VMS Configuration Client. To format the LUNs, see Bosch VMS Configuration Manual, Chapter Formatting a LUN. 2013.
DIVAR IP 3000 System setup - first steps | en 29 User accounts page You can add users and passwords. Use Configuration Client to add user groups and to change permissions. Bosch Sicherheitssysteme GmbH 2013.
en | System setup - first steps DIVAR IP 3000 Finish configuration page After clicking Save and activate the configuration is activated. After successful activation the Activate Configuration page is displayed again. Now you can store a backup of the configuration if desired: Click Save backup copy. 3.5 Using Bosch VMS Configuration Client If the IP addresses of devices that should be added do not fall within the same IP range as the DIVAR IP, we recommend using the Bosch VMS Configuration Client.
DIVAR IP 3000 System setup - first steps | en 31 The application performs a network scan for all defaulted devices. 4. To assign all devices at once, click Select All, then rightclick the selected devices, then click SetIP Addresses. The Set IP Addresses dialog box is displayed. Note: It is also possible to configure the devices individually with specific IP addresses based on MAC address. 5. Enter the starting IP address for the address range you want to use, click the Calculate tab, then click OK.
en | System setup - first steps DIVAR IP 3000 Note: Cameras in the image window with a red dot in the camera’s icon are viewed live. To verify recording functionality in the Operator Client 4 Cameras in the Logical Tree with a red dot in the camera’s icon are recording. To verify playback functionality in the Operator Client 4 The time line moves if the a camera is viewed in playback mode. Performance overview live: 4CIF Number of software 2.
DIVAR IP 3000 4 Additional Documentation and client software | en 33 Additional Documentation and client software Documentation for Bosch Security System products can be found as follows: 4 www.boschsecurity.com > select your region and your country > select Product Catalog > start a search for your product > select the product in the search results to show the existing documents. And on the following network share: 4 \\\sources Bosch Sicherheitssysteme GmbH 2013.
5 en | End-user license agreement (EULA) DIVAR IP 3000 End-user license agreement (EULA) This chapter informs you about the Microsoft License Terms for Microsoft Windows Storage Server 2008 R2 Standard. Please read the following pages carefully. 2013.
DIVAR IP 3000 Bosch Sicherheitssysteme GmbH End-user license agreement (EULA) | en 35 2013.
en | End-user license agreement (EULA) 2013.
DIVAR IP 3000 Bosch Sicherheitssysteme GmbH End-user license agreement (EULA) | en 37 2013.
en | End-user license agreement (EULA) 2013.
DIVAR IP 3000 Bosch Sicherheitssysteme GmbH End-user license agreement (EULA) | en 39 2013.
en | End-user license agreement (EULA) 2013.
DIVAR IP 3000 Bosch Sicherheitssysteme GmbH End-user license agreement (EULA) | en 41 2013.
en | End-user license agreement (EULA) 2013.
Bosch Sicherheitssysteme GmbH Robert-Bosch-Ring 5 85630 Grasbrunn Germany www.boschsecurity.
