DIVAR IP 2000 DIP-2040-00N, DIP-2042-2HD, DIP-2042-4HD en Quick Installation Guide
DIVAR IP 2000 Table of Contents | en 3 Table of contents 1 Safety precautions 4 1.1 General safety precautions 4 1.2 Electrical safety precautions 7 1.3 ESD precautions 8 1.4 Operating precautions 2 System overview 10 2.1 Device views 10 2.2 LED description - front panel 13 2.3 LAN port LED description - rear panel 14 3 System setup - first steps 15 3.1 Introduction 15 3.2 Setup instruction 15 3.3 Starting the application 16 3.
en | Safety precautions DIVAR IP 2000 Safety precautions 1 Observe the safety precautions in this chapter. 1.1 General safety precautions Follow these rules to ensure general safety: – Keep the area around the system clean and free of clutter. – Place the chassis top cover and any system components that have been removed away from the system or on a table so that they won't accidentally be stepped on.
DIVAR IP 2000 Safety precautions | en 5 Warning! Removing the housing: To avoid electric shock, the housing must only be removed by qualified service personnel. ! Before removing the housing, the plug must always be removed from the mains socket and remain disconnected while the housing is removed. Servicing must only be carried out by qualified service personnel. The user must not carry out any repairs.
en | Safety precautions DIVAR IP 2000 Warning! ! Handling of lead solder materials used in this product may expose you to lead, a chemical known to the State of California to cause birth defects and other reproductive harm. Notice! Electrostatically sensitive device: To avoid electrostatic discharges, the CMOS/MOSFET protection measures must be carried out correctly.
DIVAR IP 2000 1.2 Safety precautions | en 7 Electrical safety precautions Basic electrical safety precautions should be followed to protect you from harm and the system from damage: – Be aware of the locations of the power on/off switch on the chassis as well as the room's emergency power-off switch, disconnection switch or electrical outlet. If an electrical accident occurs, you can then quickly remove power from the system.
en | Safety precautions DIVAR IP 2000 new fuse must be the same or equivalent as the one replaced. Contact technical support for details and support. Caution! Mainboard Battery: There is a danger of explosion if the onboard battery is installed upside down, which will reverse its ! polarities. This battery must be replaced only with the same or an equivalent type recommended by the manufacturer (CR2032). Dispose of used batteries according to the manufacturer's instructions. 1.
DIVAR IP 2000 – Safety precautions | en 9 Handle a board by its edges only. Do not touch its components, peripheral chips, memory modules or contacts. – When handling chips or modules, avoid touching their pins. – Put the mainboard and peripherals back into their antistatic bags when not in use. – For grounding purposes, make sure your computer chassis provides excellent conductivity between the power supply, the case, the mounting fasteners and the mainboard. 1.
2 en | System overview DIVAR IP 2000 System overview The DIVAR IP 2000 system is an affordable, easy to use all-in-one recording and management solution for network surveillance systems of up to 16 channels. All channels are pre-licensed. Running the full Bosch recording solution including the Video Streaming Gateway to integrate 3rd party cameras, DIVAR IP 2000 is an intelligent IP storage device that provides both, a professional video recording solution and ease of operation.
DIVAR IP 2000 System overview | en 11 Front view: 1 6 2 3 4 5 1 Lock for front cover 4 LAN activity LED 2 Power on/off LED 5 System status LED 3 Hard disk access LED 6 Individual hard disk LED Bosch Sicherheitssysteme GmbH 2013.
en | System overview DIVAR IP 2000 Rear view: 1 1 2 1x eSATA for data export 3 4 4 5 6 2x USB 3.0 Note: Do not connect Note: Do not use these hard disk drives for ports for keyboard and recording. mouse connection. 2 1x Ethernet (RJ45) 5 1x VGA (monitor) 3 2x USB 2.0 6 Mains connection 100 - Note: Use these ports for 240 VAC keyboard and mouse connection. 2013.
DIVAR IP 2000 2.2 System overview | en 13 LED description - front panel This chapter describes the LED displays on the front of the chassis.
en | System overview DIVAR IP 2000 LED LED LED Description indicator color state Blue On Hard drive present. Red On Bosch provides the API to let application program to control this status. 2.3 LAN port LED description - rear panel This chapter describes the LAN port LED on the rear of the chassis. LAN connector: 1 Nr.
DIVAR IP 2000 3 System setup - first steps | en 15 System setup - first steps The following installation directive provides information on Installation and Configuration. DIVAR IP systems are based on Windows Storage Server 2008 R2 operating system. This chapter is valid for DIVAR IP models that come with preinstalled hard drives. Empty units start into the DOM recovery menu on first start. The recovery process is described in the installation manual. See also: – 3.
en | System setup - first steps DIVAR IP 2000 User with administrator rights: – User: BVRAdmin – Password: WSS4Bosch Notice! We strongly recommended not changing the user settings. Changing the user settings can result in malfunctioning of the system. 3.3 Starting the application DIVAR IP system is ready to go out of the box. The application provides a simple to install and intuitive to use solution for network surveillance systems. To start the application: 1.
DIVAR IP 2000 System setup - first steps | en 17 A series of scripts perform important setup tasks. This can take several minutes. Do not turn off the computer. A page is displayed where you can perform initial Windows configuration tasks. Note: In case of password loss a system recovery must be performed as described in the installation manual. The configuration must be done from scratch or must be imported. 10.
en | System setup - first steps 1. DIVAR IP 2000 On the default screen, double-click the Configuration Wizard icon. The Welcome page is displayed. 2. Run-through the following pages of the wizard. Welcome page 4 Click Next > to start the configuration. Notice! If VRM is not available on the computer or the license check fails, a corresponding error message is displayed. You cannot continue working with Configuration Wizard. 2013.
System setup - first steps | en DIVAR IP 2000 19 Passwords page This page allows you to specify a password to protect the devices from unauthorized access. 4 Enter the respective password, confirm the password, then click Next >. Bosch Sicherheitssysteme GmbH 2013.
en | System setup - first steps DIVAR IP 2000 Recorder page This page displays recorder information. 4 2013.09 | V4 | DOC Click Next > to continue.
System setup - first steps | en DIVAR IP 2000 21 Device Selection page This page displays all network devices that are added to the system. Clicking Update starts the scan process again. 4 Click Next > to continue. Bosch Sicherheitssysteme GmbH 2013.
en | System setup - first steps DIVAR IP 2000 Network page This page allows you to configure the network settings of connected devices. 4 2013.09 | V4 | DOC Click Next > to continue.
System setup - first steps | en DIVAR IP 2000 23 Date and Time page This page allows you to synchronize the device time with the computer time or a SNTP time server. 4 Click Next > to continue. Bosch Sicherheitssysteme GmbH 2013.
en | System setup - first steps DIVAR IP 2000 Video Quality page This page allows you to define the image quality for live-viewing and to set the maximum bandwidth. 4 2013.09 | V4 | DOC Click Next > to continue.
System setup - first steps | en DIVAR IP 2000 25 Recording page This page allows you to define the recording profiles. 4 Click Next > to continue. Bosch Sicherheitssysteme GmbH 2013.
en | System setup - first steps DIVAR IP 2000 Summary page This page displays a summary of all wizard settings. 4 2013.09 | V4 | DOC Click Apply to activate the configuration.
DIVAR IP 2000 4 Additional documentation and client software | en 27 Additional documentation and client software Documentation for Bosch Security System products can be found as follows: 4 www.boschsecurity.com > select your region and your country > select Product Catalog > start a search for your product > select the product in the search results to show the existing documents. And on the following network share: 4 \\\sources Bosch Sicherheitssysteme GmbH 2013.
5 en | End-user license agreement (EULA) DIVAR IP 2000 End-user license agreement (EULA) This chapter informs you about the Microsoft License Terms for Microsoft Windows Storage Server 2008 R2 Standard. Please read the following pages carefully. 2013.
DIVAR IP 2000 Bosch Sicherheitssysteme GmbH End-user license agreement (EULA) | en 29 2013.
en | End-user license agreement (EULA) 2013.
DIVAR IP 2000 Bosch Sicherheitssysteme GmbH End-user license agreement (EULA) | en 31 2013.
en | End-user license agreement (EULA) 2013.
DIVAR IP 2000 Bosch Sicherheitssysteme GmbH End-user license agreement (EULA) | en 33 2013.
en | End-user license agreement (EULA) 2013.
DIVAR IP 2000 Bosch Sicherheitssysteme GmbH End-user license agreement (EULA) | en 35 2013.
en | End-user license agreement (EULA) 2013.
Bosch Sicherheitssysteme GmbH Robert-Bosch-Ring 5 85630 Grasbrunn Germany www.boschsecurity.