Operating Manual
Metros digitales Laser DLR130K Bosch manual ingles www.viaindustrial.com
itales Laser DLR130K Bosch manual ingles www.viaindustrial.com
Volume
Measurement
For
volume
measu rements,
push
button
4.
The
indicator
for
volume
measurement
appears in the display.
Afterwards,
measure
the
length,
width
and
the
height, one after another,
in
the
same
manner
as
for a length measurement.
The
laser
beam
remains
switched on between all three measurements.
After taking the third measurement, the volume
is automatically calculated and displayed. The
last
individual
measured
value
is
indicated
at
the bottom in the display, while the final result
is shown at the top.
Values
exceeding
99990
ft
3
cannot
be
displayed;
“Err.”
is
indicated
in
the
display.
In
this case, switch the unit of measure to meters
(see “Changing the Unit of Measure”, page 9).
Area
or
Volume
Rounding
of
Large
Calculations
For values larger than 9999 feet or meters the
Distance
Measurer
rounds
the
calcu lated
value
to
the
nearest
10
feet
or
10
meters.
Accuracy
in
such
situations
is
always
99.95%
or better.
Continuous
Measurement
(Tracking)
(see
figure
D)
The continuous measurement mode (tracking)
is
used
for
the
transferring
of
measurements,
e.g.,
from
construction
plans.
In
continuous
measurement
mode,
the
Distance
Measurer
can
be
moved
relative
to
the
target,
whereby
the
measured
value
is
updated
approx.
every
0.5
seconds.
As
an
exampl e,
the
user
can
move
from
a
wall
to
“walk
off”
the
required
distance, while the actual distance can be read
continuously.
For
continuous
measurement,
push
button
5
until the indication
appears in the display.
Press
the
measuring
button
5
to
initiate
the
measuring
procedure.
Move
the
Distance
Measurer until the
required distance value is
indicated at the bottom of the display.
Pushing the measuring button
5
interrupts the
continuous
measurement.
The
current
measured
value
is
indicated
in
the
display.
Repeated
pushing
of
the
measuring
button
5
starts the continuous measuring again.
The
continuous
measuring
automatically
switches
off
after
5
minutes.
The
last
measured
value
remains
indicated
in
the
display. The continuous measuring can also be
ended by pushing buttons
4
or
5,
also buttons
12
or
13
, which changes the measuring mode.
Deleting
Measured
Values
Briefly
pushing
the
On/O ff
Clear
button
1
delet es
the
last
individual
measuring
value
determined
in
all
measuring
modes.
Pushing
the
button
repeatedly
deletes
the
individual
measured values in reverse order.
MEMORY
MODES
When
switching
off
the
Distance
Measurer,
the value in the memory is retained.
Storing/Adding
Measured
Values
Push
the
memory
add
button
11
in
order
to
store
the
current
measured
value
–
a
length,
area
or
volume
value,
depending
on
the
current
measuring
mode.
As
soon
as
a
value
has
been
stored,
“
M
”
is
indicated
in
the
display
and
“Add”
is
briefly
indicated next to it.
If a value is already stored in the memory, the
new
value
is
added
to
the
memory
contents,
however,
only
if
it’s
the
same
type
of
measurement.
As
an
example,
when
an
area
value
is
in
the
memory
and
the
current
measured
value
is
a
volume
value,
the
addition
cannot
take
place.
“Err.”
briefly flashes in the display.
However, values of the same type (e.g. length
values)
can
be
added
no
matter
if
they
have
been
measured
in
feet
and
inches,
decimal
feet or meters.
Subtracting
Measured
Values
Push
the
memory
subtraction
button
3
in
order
to
subtract
the
current
measured
value
from
the
memory
value.
As
soon
as
a
value
has
been
subtracted,
“
M
”
is
indicated in the display, and is briefly followed
by
“Sub.”
If
a
value
is
already
stored,
then
the
new
measured
value
can
be
subtracted
only
when
the
measures
of
unit
correspond
(see
“Storing/Adding Measured Values”).
-11-