Operating Manual
Metros digitales Laser DLR130K Bosch manual ingles www.viaindustrial.com
itales Laser DLR130K Bosch manual ingles www.viaindustrial.com
!
WARNING
at
persons
or
animals
and
Preparation
INSERTING/REPLACING
THE
BATTERY
Use
only
alkali-manganese
or
rechargeable
batteries.
Fewer measurements are possible when using
1.2 V rechargeable batteries as compared with
1.5 V batteries.
To
open
the
battery
lid
15
,
press
the
latch
of
the
battery
lid
14
in
the
direction
of
the
arrow
and remove the battery lid. Insert the supplied
batteries.
When
inserting,
pay
attention
to
the
correct polarity according to the representation
on the inside of the battery compartment.
Wh en
the
battery
symbol
appears
in
the
display
for
the
first
time,
then
at
least
100
measurements are still possible. The batteries
flashes;
taking
measu rement s
is
no
longer
possible.
Always replace all batteries at the same time.
Only use batteries from one brand and with the
identical capacity.
•
Remove
the
batteries
from
the
Distance
Measurer
when
not
using
it
for
extended
periods.
When storing for extended periods,
the
batteries
can
corrode
and
discha rge
themselves.
INSTALLING
OPTIONAL
HAND
STRAP
Feed
string
loop
on
end
of
hand
strap
23
under
hand
strap
mounting
post
24
and
pull
out on other side. Feed hand strap
23
through
string loop end and pull tight.
must
be
replaced
when
the
battery
symbol
Operation
INITIAL
OPERATION
• Protect
the
Distance
Measurer
against
moisture and direct sun irradiation.
• Do
not
expose
the
Di stance
Measurer
to
extreme
temperatures
or
variations
in
temperature.
Switching
On
and
Off
To
switch
on
the
Distance
Measurer,
either
press
the
On/Off/Clear
button
1
or
the
measuring
button
5
.
When
switching
on
the
Dista nce
M easurer,
the
laser
beam
is
not
switched on yet.
To
switch
off
the
Distance
Measurer,
press
and hold the On/Off/Clear button
1
.
To save the batteries, the Distance
Measurer
switches
off
automatically
after
approx.
5
minutes when no measurement is carried out.
When a measured value has been stored, it is
retained
in
automatic
switch-off
mode.
When
switching
on
the
Di stance
Measurer
again,
“M”
is indicated in the display.
Measuring
Procedure
The
Distance
M easurer
offers
a
variety
of
different
measuring
modes
that
can
be
selected
by
pushing
the
corresponding
mode
button (see “Measuring Mode”). After switching
on,
the
Distance
Measurer
is
in
the
“length
measurement mode”.
Also,
it
is
possible
to
select
any
of
the
two
different reference points for the measurement
by
pushing
the
reference
point
button
9
(see
“Selecting
the
Reference
Point”).
After
switching
on,
the
rear
edge
of
the
Distance
Measurer is preset as the reference point.
Upon selection of the measuring mode and the
reference point, all further steps are carried out
by pushing the measuring button
5
.
With
the
reference
point
selected,
place
the
Distance
Measurer
against
the
desired
measuring line (e.g. a wall).
Briefly
push
the
measuring
button
5
to
switch
on the laser beam.
Do
not
point
the
laser
beam
do
not
look
into
the
laser
beam
yourself,
not
even
from
a
large
distance.
-9-