Installation Manual

ManualsBrandsBosch ManualsAccess Control EquipmentAccess Control Device

DS150i/DS151i Installation Guide Request-to-Exit PIR Detectors

1.0 Description

The DS150i is a passive-infrared detector designed for request to exit

(REX) applications. It is UL Listed as an access control device under the

UL 294 standard and is listed for Class I for UL Canada (ULC-S319). For

C-UL listed installation applications, the REX shall be connected to ULC-

S319 listed compatible devices (i.e. control units, power supply and

locks). Intended for indoor use only.

The relay output consists of two Form "C" contacts that can be adjusted to

latch from approximately 0.5 sec to 64 sec. The latch time features two

modes of operation: resettable (R) and non-resettable (NR). The relay can

also be programmed to fail safe or fail secure during a power loss.

You can mount the DS150i on the ceiling or wall and aim and/or mask its

pattern for more effective use based on installation needs. The DS150i is

not designed as the primary means of exit for emergency egress

applications.

The DS150i is available in a light grey (DS150i) or a black (DS151i)

enclosure. An optional trimplate is also available in light grey (TP160) and

black (TP161).

2.0 Mounting

1. Select a mounting location over the center of the door or doors to be

covered. The target must walk directly toward the detector.

Mount the detector on the ceiling, wall, or door frame. The detector

can be surface mounted or mounted to a keyswitch plate with a "D"

size hole.

The DS150i is not tall enough to completely cover a single

gang box. Where aesthetics are important, mount it using

the optional trimplate (TP160 or TP161). Refer to Figure 1

for additional instructions for mounting with the trimplate.

Figure 1: Optional Trimplate

DOOR

DS150i/DS151i

Optional Trimplate

(TP160/TP161)

Gang box

The arrows on the base indicate its correct mounting

orientation relative to the door.

The mounting height range is from 7 ft to 15 ft.

(2.1 m to 4.6 m) above the floor.

2. Remove the back cover from the detector. Insert the head of a small

straight edge screwdriver into the locking tab and pry the back cover

off.

When the back cover is removed, the front cover and

detector module separate.

3. Route the wiring as necessary through the wiring entrance (refer to

Figure 2). For surface wiring, use the break out wiring entrance on

the front cover (at the same end as the wire entrance).

4. Loosely mount the back cover to the mounting surface using the

supplied mounting screws.

5. Mount the detector module to the back cover. Aim the detector for

the desired coverage.

Coil excess wiring behind the back cover along the

channels provided.

Figure 2: Location of Major Items

-14° 4° 14°

ON DIP

Wall Mount

Angles

Wire

Plug

LED

Ceiling Mount

Angles

Wire

Entrance

DIP

Switches

3.0 Wiring

3.1 General Information

Only apply power after all connections are made and

inspected. Remove all system power (AC and standby

battery) before wiring the device.

Attach the wiring connector (provided) to the wire plug on the circuit board

(refer to Figure 3).

Figure 3: Connector to Plug Orientation (Default Switch Settings)

Refer to Figure 4 to wire the detector’s relay contacts.

Figure 4: Relay Contact Wiring

Summary of content (4 pages)

PAGE 1
DS150i/DS151i Installation Guide Figure 2: Location of Major Items 2.0 1. Mounting Select a mounting location over the center of the door or doors to be covered. The target must walk directly toward the detector. Mount the detector on the ceiling, wall, or door frame. The detector can be surface mounted or mounted to a keyswitch plate with a "D" size hole. Wire Plug LED ON Wire Entrance DIP DIP Switches 3.0 Wiring 3.
PAGE 2
3.2 Table 1: Resettable/Non-resettable DIP Switch Settings EMF (Voltage) Spike-Protected Relay Pins 6 through 8 (wire colors gray, green, and orange) comprise the EMF spike-protected relay. Refer to Figure 3. Use this relay when connecting inductive loads to the detector. This relay protects the detector from inductive loads that might deliver damaging EMF spikes. 3.
PAGE 3
4. 5. 6. Apply power to the unit. Wait at least 3 min for the detector to settle. Test the unit by walking directly through the coverage area, toward the door. Aim the detector up or down if necessary to obtain the proper coverage. Tighten the screws after aiming the detector. Check that the relay latch time is sufficient. Adjust if necessary. After confirming proper operation, replace the cover and walk test one more time to ensure the coverage has not changed. 6.0  0 Feet 1. 2. 3.
PAGE 4
8.0 Application Notes 8.1 General 9.0 Input Power Double entry/exit doors without a center post present a problem resulting from a gap that might exist between doors. While the gap is usually filled with soft or pliable weather stripping, there is an opening that vandals can use to insert an object (such as a comb or ruler) through and into the coverage pattern of the detector.