DS7080i Version 2+ Security System User’s Guide An instruction guide For your alarm system when used with a DS7447, DS7443S or DS7445 keypad Armed Status Ready To Arm Power Fire On 1 2 3 Off 4 5 6 Perimeter Only 7 8 9 No Entry * 0 # Bypass System Reset
System Overview Congratulations on the installation of your new security system. No other investment can provide such peace of mind. Welcome to the DS7080i Version 2+ intrusion/fire control system. Since each installation is unique, your’s will contain some, but not necessarily all of the features mentioned in this guide. A security system usually consists of: • A Control Panel: The control panel is the center of your intrusion/fire alarm system.
Table of Contents System Overview 2 Understanding the DS7447, DS7443S and DS7445 Keypads 4 Understanding Partitioning 6 Turning ON (arming) your System 7 Turning ON (arming) your System (continued) 8 Quick Arming Your System 9 Turning OFF (disarming) your System / Silencing Alarms 10 Force Arming your System 11 Zone Bypass 12 Chime Mode 13 Access Control 14 Changing the Date 15 Changing the Time 16 Automatic Arming 17 Delaying Automatic Arming 18 Setting Delayed Arming 19 Emergency Procedures 20 Turning OFF
Understanding the DS7447, DS7443S and DS7445 Keypads This chart will help you understand what each Light/LED represents. Armed The DS7447 is an alphanumeric LCD keypad. The DS7443S is an LED keypad; its LEDs 1-6 represent the first 6 zones of the system. The DS7445 is an LED keypad; its LEDs 1-8 represent the 8 zones of the system. Both display information on various control panel functions. A built-in sounder is used to annunciate keystroke entries and as an interior warning device.
Understanding the DS7447, DS7443S and DS7445 Keypads (continued) Lights Present only on the DS7443S and the DS7445 Keypads Light Off Flashing Perimeter (yellow) The perimeter is not armed. This Light will not flash. The perimeter is armed. Supervisory (yellow) This Light is not used by the DS7080i V2+. Not used. Not used. Bell Silenced (yellow) The bells do not need to be or have been silenced. This Light will not flash. There has been a Fire alarm and the bells have been silenced.
Understanding Partitioning Your alarm system may be Partitioned. A Partitioned system is a system that is divided into two areas which may be armed and disarmed independently. The following applies in a Partitioned system: • User PIN numbers are always required to perform operations in a Partitioned system. • DS7447 LCD keypads will alternately display (about every 2 seconds) the current status of each partition.
Turning ON (arming) your System This chart explains the five normal ways to arm the system. The green Status Light must be on steady and the display* must read “Ready to Arm” in order to arm the system with one of these commands. Ifthe green Status Lightis noton,orifthe display*is reading “Not Ready, ”then see Force Arming or Zone Bypass for other ways to arm the system. If this is a Partitioned system, please read “Understanding Partitioning” on page 6 of this guide before using this chart.
Turning ON (arming) your System (continued) If this is a Partitioned system, please read “Understanding Partitioning” on page 6 of this guide before using this chart. Type of Arming Desired Command Sequence*** Perimeter Arming Someone still on the premises. PIN + [Perimeter Only] The entry/exit delay is in effect. Custom Arming (If programmed) Ask your installing company to explain the type of arming that occurs when using this command. Maximum Security Arming No one left on the premises.
Quick Arming Your System This chart explains four ways to quick arm the system from the keypads. If Quick Arming is not used, a PIN must be entered at the beginning of all arming command sequences. Quick Arming is not available in a partitioned system.
Turning OFF (disarming) your System / Silencing Alarms This chart explains proper procedures for disarming and/or silencing alarms. Please read the section about Emergency Procedures prior to being confronted with an emergency event. If you have entered the building through a perimeter door, you may hear a steady pre-alert tone from the keypads. If so, disarm according to the chart below.
Force Arming your System This chart explains the procedure for Force Arming your system if one or more zones are faulted. When one or more zones are faulted, the system may be Force Armed (if programmed) by bypassing the faulted zones. The green Status Light will be off on all keypads when Force Arming is required to arm the system. The DS7447 display will read “Not Ready” and the DS7443S and DS7445’s zone LEDs will be on (the DS7443S cannot display zones 7 & 8) if one of those zones is faulted.
Zone Bypass This chart explains the procedure for bypassing a faulted zone prior to arming the system. There may be occasions when it is desirable or necessary to temporarily bypass one or more zones prior to arming the system. Bypass commands only work when the control panel is disarmed. For instance, an open window may cause the DS7447 display to read “Not Ready” followed by the zone number. The DS7443S and DS7445 may have one of its zone LEDs on steady (the DS7443S cannot display zones 7 & 8).
Chime Mode This chart explains the procedure for turning ON and turning OFF Chime Mode. Chime Mode causes all the keypad sounders to beep each time a Perimeter or Entry/Exit zone is violated while the control panel is off (disarmed). The [#] [7] command is used to both turn Chime Mode off and on. You cannot set the Chime mode by partition.
Access Control This chart explains the procedure for activating devices that require an Access Control PIN. Your system may or may not use a keypad key sequence to activate other electrical devices. The special PIN required to perform this function is known as an Access Control PIN. This feature can be used in armed or disarmed modes. The PIN may control devices that activate for a short period of time (e.g. electric locking mechanisms on a door).
Changing the Date This chart will guide you through the steps necessary to Change the Date displayed at the keypads. You should write down your entries before you enter the Master Code Programming Mode and have them with you as you begin programming. Make your entries promptly. If a long delay occurs in your entries, the 3-beep error tone sounds and exits you from the programming mode. It is recommended that this procedure be performed at a DS7447 keypad.
Changing the Time This chart will guide you through the steps necessary to change the Time displayed at the keypads. You should write down your entries before you enter the Master Code Programming Mode and have them with you as you begin programming. Make your entries promptly. If a long delay occurs in your entries, the 3-beep error tone sounds and exits you from the programming mode. It is recommended that this procedure be performed at a DS7447 keypad.
Automatic Arming Each partition can be programmed to automatically arm once per day. To program the Automatic Arming time , perform the following: Setting the Automatic Arming Time Enter a Master PIN + [#] + [0] Notes Setting the Automatic Arming Time can only be performed with a Master PIN Code. Enter a [1] to enter the Automatic Arm Setup programming Enter the partition number. Press [#] to exit. Enter a time for each day. Enter in [0] [1] [0] [0] [#] format.
Delaying Automatic Arming This section explains how to delay the Automatic Arming Time. To inform occupants that the system is about to arm, a pre-arming period will begin 15 minutes before the system arms automatically. If programmed by the installing company, the keypad sounders, and any outputs programmed to follow the keypad sounders, will pulse five times every minute. During the last five minutes before arming, these sounders will be on steady. Once per minute the keypad will read, “Arm in nn min.
Setting Delayed Arming This section explains how to cause the system to arm after a specified number of hours. Delayed arming is simply causing the system to arm after a specified number of hours.
Emergency Procedures Identifying Alarm Sounds Your alarm system may be programmed for a steady alarm sound or a pulsed alarm sound. It is important to learn the difference between a fire alarm sound and an intrusion alarm sound before you are confronted with an actual emergency. Silencing Alarms All alarms can be silenced with any PIN that has disarm privileges. Entering your PIN + [Off] will silence the alarm and turn off (disarm) the control.
Turning OFF (disarming) your System under Duress This chart explains the proper procedure for disarming under Duress. Ask your installer if the Duress feature has been activated. A Duress code is used when someone demands, by threatening your life or well-being, that the system be turned off. When used, the code will both turn off the system and report a silent Duress alarm if connected to a monitoring service.
Emergency Keypad Alarms / Silencing Alarms Armed Status Armed 1 4 Status 2 5 Power 3 6 Fire Power TES T WEEKLY Fire On 1 2 3 Off 4 5 6 Perimeter Only 7 8 9 * 0 # No Entry By pass B C Perimeter Status Supervisory Power Bell Silenced Fire Trouble 1 2 3 4 5 6 7 8 On On 1 2 3 Off 4 5 6 Perimeter Only 7 8 9 No Entry * 0 # Bypass 1 2 3 Off 4 5 6 Perimeter Only 7 8 9 No Entry * 0 # Bypass System Reset Sy stem Reset A Armed A B C Sys tem
Fire Reset / Fire Trouble Fire Reset Fire Trouble During a fire alarm, exit the premises immediately. When you have determined there is no fire, it is recommended that you silence the bells/ sirens before you initiate the [System Reset] command. A Fire Trouble display signifies a problem with the fire system, such as a break in the wiring that monitors smoke detectors.
Fire Safety No fire detection system should be considered 100 percent foolproof This fire alarm system can provide early warning of a developing fire. Such a system, however, does not ensure protection against property damage or loss of life resulting from a fire. Any fire alarm system may fail to warn for any number of reasons (e.g. smoke not reaching a detector that is behind a closed door).
Fire Safety (continued) • Provide a barricade between family members and fire, smoke, and toxic gases (e.g. close all bedroom doors before retiring). • Children should be instructed on opening their bedroom windows and exiting safely from the building. If exiting is not possible, they should be taught to stay at the open window and shout for help until it arrives. • In the event of a fire alarm after retiring, wake the children by shouting to them from behind your closed door.
Personal Identification Numbers General Information When programing Personal Identification Numbers, it is helpful to know the following terms: • PIN: Personal Identification Number. This is the 4 or 6 digit code users enter at the keypad to gain access to the system. A PIN may be assigned to each User Number 001 - 015. • Partition (Area): This is the area the User has authority in. You may select Partition (Area) 1, 2 or both. • User Number: This is the number that identifies each person using the system.
Personal Identification Numbers (continued) PIN Authority Levels 0 = Master: Can enter all commands, add or change PINs, change time and date, bypass, arm, set autoarm, disarm, perform system tests, system reset, and view history. PIN 001 must be a master code and must have authority 0. Any or all PINs may be master codes. 4 = Temporary: Valid only for a limited time. Can arm and disarm the system, but can not perform any other functions.
Personal Identification Numbers (continued) This chart will guide you through the steps necessary to change a PIN. You should write down your entries before you enter the Master Code Programming Mode and have them with you as you begin programming. Make your entries promptly. If a long delay occurs in your entries, the 3-beep error tone occurs and exits you from the programming mode. Steps to Change a PIN # 1. Enter the Master Code Programming Mode. # 2. Enter a 0. # 3. Enter the User Number. # 4.
Error Displays This chart explains the procedure for reading Error messages when the green Power Light is flashing. Control panel problems are indicated by a flashing green Power Light and the DS7447 display reading “Control Trouble, Enter #87.” Error messages may only be read when the control is disarmed. Contact your installing company if the problems persist. 1. “AC Power Failure”* or LED #1 on steady**: There is a power failure and the control panel is running on backup battery. 6.
Testing Your System This chart explains the procedure for performing a Zone Test. It is recommended that the system be tested weekly. The Zone Test is used to confirm that detectors will report alarms to the keypad. A Zone Test works on all zones, except 24-hour zones and fire zones. While the keypad is in a Zone Test, no control panel alarms will activate an alarm, except 24-hour zone alarms and fire alarms; these will override the Zone Test function.
Testing Your System (continued) This chart explains the procedure for performing a Battery Test. If a power failure occurs, your control panel has a built-in battery that will continue to power the control panel for many hours. The control panel automatically recharges the battery when power is restored. In addition to an automatic battery test performed every 2 minutes, the battery may also be tested manually.
Testing Your System (continued) This chart explains the procedure for performing a Communicator Test. This test is available only if your system transmits alarms and system information to a monitoring service, and has been programmed by the security installing company to permit communicator tests. A long beep will initially sound to acknowledge the start of the test. If the test is successful, the sounder will again issue one long beep. If the test fails, the keypad sounder will turn ON continuously.
Event History Readback This chart explains the procedure for performing an Event History Readback. The History Buffer stores the last 100 events in memory. The most recent 10 events are stored in non-volitile memory and will be retained even in the event of a power loss. The DS7447 can display all of these events. The DS7443S and DS7445 keypads will only display those zones that have alarmed. The DS7443S cannot display zones 7 & 8.
Glossary Access Control PIN An Access Control PIN is a special code used to activate electric door locks or other mechanisms connected to the control panel that require this code to turn them on or off. Armed/Disarmed Arming the system (burglar zones) means to turn it on. Disarming the system means to turn it off. Remember, fire protection (if installed) is always Armed/on.
Quick Reference Guide This system should be tested weekly to ensure it is functioning properly. If problems are detected in testing or changes are noticed in normal operation, call your installing company for service. The manufacturer recommends replacing the system battery every 3 to 5 years. Monitoring Service Phone Number. ______________________________ Monitoring Service System Number.
System Features Reference Guide Perimeter Arming, with entry delay: [PIN] + [Perimeter Only] Audible Alarm Signaling Device Sounds Intrusion ( ) Pulse ( ) Continuous Fire ( ) Pulse ( ) Continuous Maximum Security Arming: [PIN] + [No Entry] + [On] Keypad Supplemental Alarm [B] Key ( ) Continuous ( ) Silent This system has the Duress Alarm feature. ( ) Yes ( ) No This system has the communicator test feature. ( ) Yes This system is partitioned.
System Features Reference Guide (continued) Chime Mode PIN + [#] [7] Error Display PIN + [#] [8] [7] Zone Test PIN + [#] [8] [1] Error Display Reset PIN + [System Reset] Read Event History PIN + [#] [8] [9] Clear Zone Bypass PIN + [Bypass] [*] to clear Battery Test PIN + [System Reset] Access Control PIN + [Off] Communicator Test PIN + [#] [8] [2] Set Delayed Arming PIN + [#] [99] Fire Reset PIN + [System Reset] Delay Auto Arm by 30 Minutes PIN + [OFF] Fire Trouble PIN + [Off] to silence, PIN +
Index A AC Power Failure 29 AC power failure 11 Access Control 14 Access Control PIN 34 Access PIN 27 Arm Only PIN 27 Armed 34 Authority Level 26 Automatic Arming 17 Aux Power Fault 29 B Battery Test 31 Battery Trouble 29 bypass 12 C Central Station 34 change a PIN 28 Change the Date 15 change the time 16 Chime Mode 13 Communicator Err 29 Communicator Test 32 Control Panel 2 Control Station 2 Control Trouble 29 Custom Arming 6, 34 D Date 15 delay auto arm 18 Delayed Arming 19 Delayed Automatic Arming 18
Notes Page 39
Detection Systems, Inc., 130 Perinton Parkway, Fairport, New York, USA 14450-9199 (585) 223-4060 • (888) 289-0096 • Fax: (585) 223-9180 Copyright © 2001 Detection Systems, Inc.
