–2–
System Overview Congratulations on the installation of your new security system. No other investment can provide such peace of mind. Welcome to the DS7400Xi intrusion/fire control system. Since each installation is unique, yours will contain some, but not necessarily all of the features mentioned in this guide. A security system usually consists of: • A Control Panel: The control panel is the center of your intrusion/fire alarm system.
Table of Contents System Overview ................................................................ 3 Tips, Notes, Cautions, and Warnings ................................ 5 Typographical Conventions ................................................ 5 Fire Reset / Fire Trouble .................................................. 28 Fire Safety ........................................................................ 29 If Installed in Family Residences .............................................
Conventions Used in this Guide Tips, Notes, Cautions, and Warnings Throughout this User’s Guide helpful tips and notes will be presented on the use of your security system. They will be indicated as follows: Warnings of the possibility of injury to the user or physical damage to the equipment. Cautions about possible physical damage to the equipment. Important information to aid you in the effective use of your security system.
Understanding Partitioning Your alarm system may be Partitioned. A Partitioned system is a system that is divided into up to eight areas which may be armed and disarmed independently. Each keypad and keyfob may be assigned to arm and disarm individual partitions or the entire system. Only your installing company can change which partitions a keypad or keyfob affects. If a keypad is set to arm and disarm the entire system, then you may assign user codes (PINs) to arm and disarm individual partitions.
Understanding the DS7447/DS7447E and DS7445/DS7445i Keypads Day to Day Operations This chart will help you understand what each Light/LED on a Standard wired keypad represents. (For other keypad operations, see also, The Master Keypad and ) Day to Day Operations The DS7447/DS7447E is an alpha-numeric LCD keypad. The DS7445/DS7445i is an LED keypad; its LEDs (1-8) represent the first 8 zones of the system. Both display information on various control panel functions.
Understanding the DS7447/DS7447E and DS7445/DS7445i Keypads (continued) These LEDs Present on the DS7445/DS7445i Only: LED Perimeter (yellow) Supervisory (yellow) Bell Silenced (red) Off Panel is disarmed or is not armed perimeter. There are no supervisory alarms present. The bells do not need to be or have not been silenced. Flashing This LED will not flash On The perimeter is armed. A supervisory condition exists. This LED will not turn on steady.
Understanding the RF3341 Keypad and Keyfobs General Information Your security system may use keypads or keyfobs which use a radio frequency to transmit signals to your security system. These RF (wireless) devices are programmed with a unique code which will allow only your keypads and keyfobs to work with your security system. Although the range of your RF devices may be up to 500 feet (150 meters) in open air, normal building materials can greatly reduce their range.
Day to Day Operations Standard Operations This section describes the standard (those built and programmed into your system at the factory) procedures for arming and disarming your security system. Your installing conpany can program your system for various optional operations (see also, Optional Operations). Normal Arming Used when no one is left on the premises, all zones are to be armed, and an entry/exit delay is in effect.
Day to Day Operations (continued) Standard Operations (continued) Perimeter Instant Arming Used when someone is still on the premises, only the exterior (perimeter) zones are to be armed, and an exit delay is in effect, but no entry delay is in effect so an alarm will occur upon entry. The green Status LED must be lit and, if using a DS7447/DS7447E keypad, “Ready to Arm” must be displayed.
Day to Day Operations (continued) Standard Operations (continued) Perimeter Arming Used when someone is still on the premises, only the exterior (perimeter) zones are to be armed, and an entry/exit delay is in effect. The green Status LED must be lit and, if using a DS7447/DS7447E keypad, “Ready to Arm” must be displayed. If the green LED is not on or the keypad displays “Not Ready,” see Force Arming or Zone Bypass in Optional Procedures for other ways to arm the system.
Day to Day Operations (continued) Standard Operations (continued) Custom Arming Used to alarm zones that you specify and your installer programs into your system. An entry/exit delay will be in effect unless otherwise programmed. The green Status LED must be lit and, if using a DS7447/DS7447E keypad, “Ready to Arm” must be displayed. If the green LED is not on or the keypad displays “Not Ready,” see Force Arming or Zone Bypass in Optional Procedures for other ways to arm the system.
Day to Day Operations (continued) Standard Operations (continued) Maximum Security Arming Used when no one is still on the premises, all zones are to be armed, and an exit delay is in effect, but no entry delay is in effect so an alarm will occur upon entry. The green Status LED must be lit and, if using a DS7447/DS7447E keypad, “Ready to Arm” must be displayed.
Day to Day Operations (continued) Standard Operations (continued) Normal Disarming Please read the section about Emergency Procedures prior to being confronted with an emergency event. If you have entered the building through a perimeter door, you may hear a steady entry alert tone from the wired keypads. If so, disarm according to the chart below.
Day to Day Operations (continued) Optional Operations Quick Arming Quick Arming allows some arming commands to to entered without first entering a PIN. If Quick Arming is not used, a PIN must be entered at the beginning of all arming command sequences. Note: Quick Arming is not available from a Master keypad nor from RF (wireless) keypads.
Day to Day Operations (continued) Optional Operations (continued) Force Arming Force Arm serves as a warning that the control panel is operating under backup battery. Bypassing or Force Arming removes some of your building’s protection because it excludes the faulted zones from arming. Therefore, an intrusion may not be detected or the detection may be delayed. Always attempt to correct any zone problems (close doors and windows, etc.) before using these features.
Day to Day Operations (continued) Optional Operations (continued) Zone Bypass There may be occasions when it is desirable or necessary to temporarily bypass one or more zones prior to arming the system. Bypass commands only work when the control panel is disarmed. For instance, an open window may cause the DS7447/DS7447E display to read “Not Ready” followed by the zone number. The DS7445/DS7445i may have one of its zone 1-8 LEDs on steady.
Day to Day Operations (continued) Optional Operations (continued) Automatic Arming Each partition can be programmed to automatically arm once per day. Automatic Arming is not programmable from an RF (wireless) keypad. If Automatic Arming is used in Master Keypad mode, it will affect all partitions you have access to. If used in single partition mode, or from a single partition keypad, it will affect only the partition you are working in.
Day to Day Operations (continued) Optional Operations (continued) Delaying Automatic Arming When Automatic Arming is set, to inform occupants that the system is about to arm, a pre-arming period will begin 15 minutes before the system arms automatically. The keypad sounders, and any outputs programmed to follow the keypad sounders, will pulse five times every minute. During the last five minutes before arming, these sounders will be on steady.
Day to Day Operations (continued) Optional Operations (continued) Automatic Disarming Each partition can be programmed to automatically disarm once per day. Automatic Disarming is not programmable from an RF (wireless) keypad. If Automatic Disarming is used in Master Keypad mode, it will affect all partitions you have access to. If used in single partition mode, or from a single partition keypad, it will affect only the partition you are working in.
Day to Day Operations (continued) Optional Operations (continued) Delayed Arming Delayed Arming is simply causing the system to arm after a specified number of hours. Delayed Arming is not available from RF (wireless) keypads. Delayed Arming can be used even if there are no Automatic Arming times programmed. If Delayed Arming is used in Master Keypad mode, it will affect all partitions you have access to.
Day to Day Operations (continued) Optional Operations (continued) Chime Mode Chime Mode causes the keypad sounders to beep each time a Perimeter or Entry/Exit zone is violated while the control panel is off (disarmed). The [#] [7] command is used to turn Chime Mode both off and on.
Day to Day Operations (continued) Optional Operations (continued) Access Control Your system may use a keypad key sequence to activate other electrical devices. Access Control is not available from an RF (wireless) keypad or from the keyfobs. Note: This feature can be used in armed or disarmed modes. The special PIN required to perform this function is known as an Access Control PIN. The PIN may control devices that activate for a short period of time (i.e. electric locking mechanisms on a door).
Day to Day Operations (continued) Optional Operations (continued) Changing the Date The System Date can only be changed in Master Programming Mode, so it is not programmable from an RF (wireless) keypad. Note: You should write down your entries before you enter the Master Programming Mode and have them with you as you begin programming. Make your entries promptly. If a delay of 15 seconds or more occurs between your entries, the 3-beep error tone occurs and exits you from the programming mode.
Day to Day Operations (continued) Optional Operations (continued) Setting the System Clock Setting the time on the System Clock can only be done in Master Programming Mode, so it is not programmable from an RF (wireless) keypad. Note: You should write down your entries before you enter the Master Code Programming Mode and have them with you as you begin programming. Make your entries promptly.
Emergency Procedures Identifying Alarm Sounds Caution When Entering A Building Your alarm system may be programmed for a steady alarm sound or a pulsed alarm sound. It is important to learn the difference between a fire alarm sound and an intrusion alarm sound before you are confronted with an actual emergency.
Emergency Procedures (continued) Fire Reset / Fire Trouble Fire Reset Fire Trouble During a fire alarm, exit the premises immediately. When you have determined there is no fire, you must silence the bells/sirens before you can initiate the [System Reset] command. A Fire Trouble message with a zone number signifies a problem with the fire system, such as a break in the wiring that monitors smoke detectors.
Emergency Procedures (continued) Fire Safety WARNING: No fire detection device or system should be considered 100 percent foolproof. This fire alarm system can provide early warning of a developing fire. For added early warning protection, it is recommended that detectors Such a system, however, does not ensure protection against property be installed in all separated areas including the basement, bedrooms, damage or loss of life resulting from a fire.
Emergency Procedures (continued) Fire Safety (continued) • Provide a barricade between family members and fire, smoke and toxic gases (i.e. close all bedroom doors before retiring). • Children should be instructed on opening their bedroom windows and exiting safely from the building. If exiting is not possible, they should be taught to stay at the open window and shout for help until it arrives.
Emergency Procedures (continued) Emergency Keypad Alarms / Silencing Alarms The Emergency Alarm Keys [ ], [ ], and [ ] may generate Fire, Special Emergency and Panic Alarms if programmed by the installer. Ask your installing company to explain the function of these keys. When using the Emergency Keys, they must be pressed for two seconds to generate an alarm. Use the Disarming Command Sequence to cancel or silence these alarms.
Emergency Procedures (continued) Turning OFF (Disarming) Your System Under Duress A Duress PIN (see also, Personal Identification Numbers, PIN Authority Levels) is used when someone demands, by threatening your life or well-being, that the system be turned off. When used, the Duress PIN will both turn off the system and report a silent Duress alarm if connected to a monitoring service. Extreme care should be used when entering your PIN to turn off the system, so a Duress PIN is not inadvertently entered.
Personal Identification Numbers General Information When programming Personal Identification Numbers, it is helpful to know the following terms: • PIN: Personal Identification Number. This is the 4 or 6 digit code users must enter at the keypad to gain access to the system. A PIN may be assigned to each User Number 001 through 200. • User Number: This is the number that identifies each person using the system. There are 200 possible User Numbers available for use (001 through 200).
Personal Identification Numbers (continued) Changing a PIN PINs can only be changed in Master Programming Mode, so they are not programmable from an RF (wireless) keypad. Note: You should write down your entries before you enter the Master Code Programming Mode and have them with you as you begin programming. Make your entries promptly. If a long delay occurs in your entries, the 3-beep error tone occurs and exits you from the programming mode.
Personal Identification Numbers (continued) PIN Authority Levels 0 = Master: Can enter all commands, add or change PINs in assigned partitions, change the time and date, bypass, arm, disarm, perform system tests, system reset and view history. User Number 001 must have the Master authority level. Any or all PINs can behave as a Master code. 1 = Unlimited: Can enter all commands, bypass, arm, disarm, system reset and perform system tests. It can not change PINs. 2 = General: Can bypass, arm and disarm.
Personal Identification Numbers (continued) Changing the Expiration Date for Temporary PINs The Expiration Date for Temporary PINs can only be changed in Master Programming Mode, so they are not programmable from an RF (wireless) keypad. Note: You should write down your entries before you enter the Master Code Programming Mode and have them with you as you begin programming. Make your entries promptly.
Error Displays Error Displays can only be read when the control is disarmed. Some Control Panel Errors, such as battery trouble and any RF troubles, will cause the keypad sounders to beep every 10 seconds. The keypad sounders may be silenced for 4 hours by entering: [PIN] + [Off]. The sounders will continue to resound until the problem is fixed.
Error Displays and Warnings (continued) System Faults System faults are designated as follows: [#] [8] [7] will display RAM Fault ROM Fault EEPROM Fault Ground Fault 2Ph/Bell Fault = loss of communication to DS7420I Line 1 Fault = DS7420I phone line 1 fault Line 2 Fault = DS7420I phone line 2 fault Bell Fault = DS7420I bell circuit fault Aux. Relay Fault = DS7420I aux. relay fault Oct.
Testing Your System Zone Test The Zone Test is used to confirm that detectors will report alarms to the keypad. A Zone Test works on all zones, except 24-hour zones and fire zones. While the keypad is in a Zone Test, no control panel alarms will activate an alarm, except 24-hour zone alarms and fire alarms; these will override the Zone Test function. This test requires you to manually alarm each zone.
Testing your System (continued) Battery Tests If a power failure occurs, your control panel has a built-in battery that will continue to power the control panel for many hours. The control panel automatically recharges the battery when power is restored. In addition to an automatic battery test performed every 2 minutes, the battery may also be tested manually. This test also uses the battery to manually activate all the system sounders for 2 seconds ([PIN] [#] [8] [5] only).
Testing your System (continued) Communicator Test This test is available only if your system transmits alarms and system information to a monitoring service, and has been programmed by the security installing company to permit communicator tests. This test can be performed from a Master Keypad. The account code for partition #1 will be used. System Tests are not available from RF (wireless) keypads. A long beep will initially sound to acknowledge the start of the test.
Testing your System (continued) Fire Walk Test This test is used to confirm that Smoke detectors will report alarms to the keypads. The Fire Walk Test tests all fire zones, including verified fire and waterflow. This test requires you to manually alarm each zone. At the start of the Fire Walk Test a Fire Walk Test report, if programmed, is sent to the central station. Fire alarm reports are not sent to the central station during the Fire Walk Test.
Testing your System (continued) Event History Readback The History Buffer stores the last 400 events in memory. The DS7447/DS7447E can display all of these events. The DS7445/DS7445i will only display those zones (1-8) that have alarmed since the last Event History Readback. If this test is performed from a Master keypad, it must be in Single Partition Mode. The RF3341 cannot display history events.
The Master Keypad - DS7447/DS7447E only General Information Your system may include a Master keypad. A Master keypad is a DS7447/DS7447E keypad programmed to give a user access to all the partitions he has access to, not just the partition in which the Master keypad is located. This is different from a Standard keypad in that Standard keypads only give access to the single partition in which they are located. Commands entered at the Master keypad will affect all the partitions to which the user has access.
The Master Keypad (continued) Master Keypad Displays (continued) This chart will help you understand what each LED function of the Master keypad represents. LED Armed (red) Status (green) Power (green) Fire (red) Off All partitions are disarmed. Not ready to arm (if the Armed LED is on, all partitions are armed). The control panel has lost all power; no AC or battery. There are no fire alarms Flashing One or more partitions are armed, or an alarm has occurred. One or more zones are bypassed.
The Master Keypad (continued) Single Partition Mode Single Partition Mode is used to control partitions on a “one at a time/one by one” basis from the Master keypad. To enter the Single Partition Mode, enter your [PIN], then press the [#] key twice. This will call up the first partition you have access to. Enter the command sequence you wish for this partition. You do not need to use your PIN again. To move on to the next partition you have access to, press the [#] key twice.
The Master Keypad (continued) Arming from the Master Keypad Type of Arming Desired Arming All the Partitions to which You Have Access Arming Only Some of the Partitions to which You Have Access Command Sequence [PIN] + any Arming Command Sequence This will arm all the partitions to which you have access even if they are already armed. 1. 2. 3. 4. 5. 6. 7. [PIN] + [#] + [#]. This puts you into Single Partition Mode. The first partition to which you have access is displayed: “Ready to Arm. Cafeteria.
The Master Keypad (continued) Disarming from the Master Keypad Type of Disarming Desired Disarming All the Partitions to which You Have Access Disarming Only Some of the Partitions to which You Have Access Command Sequence [PIN] + [Off] This will disarm all the partitions to which you have access even if they are already disarmed. 1. 2. 3. 4. 5. 6. 7. [PIN] + [#] + [#]. This puts you into Single Partition Mode. The first partition to which you have access is displayed: “Armed. Cafeteria.
Glossary Access Control PIN An Access Control PIN is a special code used to activate electric door locks or other mechanisms connected to the control panel that require this code to turn them on or off. Armed/Disarmed Arming the system (burglar zones) means to turn it on. Disarming the system means to turn it off. Remember, fire protection (if installed) is always Armed/on.
Glossary (continued) Local System A Local System is a system that has a control panel that is not programmed to call a monitoring service. It will sound only local (on sight) bells or sirens when an intrusion or fire alarm is detected. Monitored System A Monitored System is a system that uses phone lines to notify a monitoring service of programmed abnormal events such as burglar or fire alarms. Partition A Partition exists when the system is divided up into 2, 3, 4, 5, 6, 7, or 8 areas or Partitions.
Index A Access Control ....................................... 24 PIN ...................................................... 35, 49 Alarm Sounds ......................................... 27 Alarms Fire ............................................................. 27 Silencing .............................................. 27, 31 Arm Only PIN .......................................... 35 Armed Light .............................................. 7 Arming Automatic ..........................................
Index (continued) K P T Keyfobs ..................................................... 9 Keypads .................................................... 3 Partition .............................. 6, 46, 47, 50 Perimeter Light ......................................... 8 PINs ....................................................... 35 Power Light .............................................. 7 Protected Zones ....................................... 3 Telephone Line Seizure ...........................
Quick Reference Guide Maintenance and Service The system should be tested weekly to ensure it is functioning properly. If problems are detected in testing or changes are noticed in normal operation, call your installing company for service. The manufacturer recommends replacing the system battery every 3 to 5 years. Monitoring Service Phone No. ______________________________ Monitoring Service System No. ______________________________ Installing Company Phone No.
Quick Reference Guide (continued) – 54 –
Quick Reference Guide (continued) Zone Protection 129_______________ 130_______________ 131_______________ 132_______________ 133_______________ 134_______________ 135_______________ 136_______________ 137_______________ 138_______________ 139_______________ 140_______________ 141_______________ Zone Protection 142_______________ 143_______________ 144_______________ 145_______________ 146_______________ 147_______________ 148_______________ 149_______________ 150_______________ 151_______________ 152____
Quick Reference Guide (continued) Zone Protection 193_______________ 194_______________ 195_______________ 196_______________ 197_______________ 198_______________ 199_______________ 200_______________ 201_______________ 202_______________ 203_______________ 204_______________ 205_______________ Zone Protection 206_______________ 207_______________ 208_______________ 209_______________ 210_______________ 211 _______________ 212_______________ 213_______________ 214_______________ 215_______________ 216___
This page intentionally blank – 57 –
System Features Reference Guide Audible Alarm Signalling Device Sounds Intrusion ( ) Pulse ( ) Continuous Fire ( ) Pulse ( ) Continuous Custom Arming [PIN] + [#] + [4] for __________ This system has the Duress Alarm feature. ( ) Yes ( ) No Force Arming Enter an arming command sequence followed by the [Bypass] key on DS7447/DS7447E/DS7445/DS7445i keypads or the [9] key for RF3341 keypads. The maximum number of zones that can be forced armed is _____ This system has the communicator test feature.
System Features Reference Guide (continued) Partitioning ( ) Partitioning enabled ( ) Partitioning not enabled ( ) Number of Partitions Commands for Other System Features Chime Mode [PIN] + [#] [7] Zone Test [PIN] + [#] [8] [1] Battery Test [PIN] + [System Reset] Communicator Test [PIN] + [#] [8] [2] Error Display [PIN] + [#] [8] [7] Error Display Reset [PIN] + [System Reset] Fire Reset [PIN] + [System Reset] Event History Readback [PIN] + [#] [8] [9] Fire Walk Test [PIN] + [#] [9] [1] Access Control Enter
For Service Please contact your installing company at Copyright © 2007 Bosch Security Systems, Inc.