INSTALLATION INSTRUCTION EX30 Infrared Imager™ MAN-30-06 -1-
IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep this instruction. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with manufacturer instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat. 9.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the power where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13.
® IMPORTANT For best results, please read this Instruction Booklet prior to installing the EX30 Infrared Imager. WARNING ! CSA Certified / UL Listed CLASS 2 power adaptors must be used in order to comply with electrical safety Only qualified personnel shall install any EXTREME CCTV®surveillance camera. EXTREME CCTV® will not be responsible for injuries or damages resulting from the improper installation or use of any equipment sold by EXTREME CCTV®, their agents, distributors or dealers.
NOTE: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. As part of its’ normal operation this device can generate radio frequency energy and if not installed and used in accordance with the installation manual may cause interference to radio communications.
INDEX – EX30 Infrared Imager™ PAGE DESCRIPTION................................................................. 7 UNPACKING.................................................................... 8 PARTS LIST .................................................................... 8 ITEMS REQUIRED FOR INSTALLATION....................... 8 INITIAL PREPARATIONS ............................................... 9 GUIDELINES ................................................................... 9 1.
DESCRIPTION The EX30 Infrared Imager consists of an LXR camera and an infrared illuminator. This surveillance system gives optimum performance during daylight conditions and in the pitch black of night. The camera has a “Vari Focal” lens, and is seamlessly switched by a photocell when light conditions change from day to night, ensuring no loss of image quality. An all-weather housing with tough polycarbonate windows contains all the electronics.
UNPACKING Care should be taken when unpacking the shipped unit. Check the parts list and confirm all items have been located. Inspect the equipment thoroughly to ensure nothing was damaged in transit. Contact BOSCH Service Center if a problem is noted, see the rear page of this booklet for contact numbers. PARTS LIST (items supplied with unit) - EX30 camera assembly Installation Instructions booklet Cardboard box containing one adjustable wall mounting bracket.
INITIAL PREPARATIONS • Determine the operating voltage at the installation site. The camera‘s Voltage Regulator Board accepts both 10.5-40VDC and 12-28VAC input without change to internal connections. • Determine the optimum mounting location for the camera. See Section 4, Camera Mounting. • All cameras have been tested and pre-focused with telephoto setting as factory default prior to shipment. If any adjustment needed, it is advisable to check the camera’s operation before installation.
1. MOUNTING BRACKET PREPARATION EXMB.028 Mounting Bracket SET SCREW • • Use the supplied Allen Key to remove the setscrew from the supplied mounting bracket. Separate the two sections of the mounting bracket.
2. CABLE / BRACKET INSERTION EX30 Camera • • Carefully feed the Power/BNC cable through both sections of the mounting bracket. Make sure the cable is not kinked, chafed, or split during this procedure.
3. MOUNTING BRACKET ATTACHMENT • • • • Attach the Mounting Bracket to the Camera’s Mounting Block using the six bolts supplied with the bracket. Snug the two halves of the bracket together with the Allen head set screw. Tighten the setscrew enough so that the camera can be adjusted for angle. Do not over-tighten. Note the angled part of the mounting bracket faces to the rear of the camera.
4. CAMERA MOUNTING Warning: this apparatus must be securely attached to the wall or ceiling in accordance with installation instructions. Failure to follow installation instructions ma results in injury/death. Select a suitable location that protects the camera from accidental damage, tampering and environmental conditions exceeding the specifications of the camera to be mounted.
• Installation should only be performed by skilled personnel Hardware required: • For ceiling mount: 1. Mounting Bracket, Model EXMB.029, Qty = 1 2. ¼’’ x 2” Lag Screws, Qty = 1 3. ¼’’ Washer, Qty = 1 • For wall mount: 1. Mounting Bracket, Model EXMB.028, Qty = 1 2.
mounting using the following wood screws secured into a 2x4 stud under ½” drywall: • wood screws with washer, 1/4” lag, dia Ø1/4”, 2” long, 9 TPI, with ½” head • 16” flat washer. Camera has not been evaluated for safety requirements using other mounting kits. Installation (Ceiling and Wall Mount) • Locate stud in the ceiling/wall and mark outside edges of stud. • Using ceiling/wall mount bracket as a template, align the mounting hole with the center of the stud.
5. CAMERA LENS ADJUSTMENTS AND SELECTING THE WINDOW For optimum picture quality, the camera lens should be as close as possible to the inside face of the viewing window, without touching. The camera is pre-focused with telephoto setting as factory default. Follow the steps below if any adjustment needed. • • • Loosen the four bolts from the extrusion. Remove the faceplate, window and the lens foam, set aside. Make sure the photocell is not dislodged. Do proper adjustment as 5.
Loosen this setscrew for Focus Adjustment Loosen this setscrew for Telephoto or Wide Angle Adjustment 5.1. Vari Focal and “Auto-Iris” Control Adjustments • • • • Loosen the lens set screws for focus/zoom adjustments. The setscrew marked N ←→ ∞ is used for image focus. The setscrew marked T←→ W is used for telephoto or wide-angle settings. Re-tighten the setscrews after focus adjustments have been completed.
Telephoto (Factory standard) Use 40º illumination beam Wide Use 80ºillumination beam Use a Neutral Density filter or Infra-Red Pass filter to cover the lens during focusing to simulate low light conditions on scene for correct 24-hour focusing. For camera with varifocal lens, the camera should be focused with the lens iris fully opened to simulate the worst possible depth of field.
6. LED ARRAY - POWER ADJUSTMENTS If adjustment is needed, remove the rear cover for access to the LRB. The EX30 needs to be powered-up while making the LED power adjustments. Cover the photocell to turn the LEDs “ON” (850nm LEDs will have a slight red glow). For photocell “On/Off” light-level adjustment, rotate VR2. Clockwise is off and counter-clockwise is on.
7. OSD ADJUSTMENT 1. 2. 3. Open the back cover of EX30 to access the OSD controls. Enter the OSD menu by pressing the joystick button down. Follow the instructions below to make camera adjustments.
8.
Note The following default settings should not be changed: Lens = DC; E.
- 23 -
- 24 -
- 25 -
- 26 -
- 27 -
Note The following default setting should not be changed.
- 29 -
- 30 -
- 31 -
- 32 -
- 33 -
- 34 -
- 35 -
- 36 -
- 37 -
- 38 -
- 39 -
9. CAMERA RE-ASSEMBLY Make sure all wires are properly connected, all holes are sealed against moisture penetration, and all mounting screws are tight. • • • • Slide the lens foam over the camera lens. Make sure the foam is snug and as close to the faceplate viewing window as possible and the photocell is secure with an unobstructed view. Attach the window, faceplate, and the rear cover to the camera housing. Tighten the four bolts.
10. TROUBLESHOOTING GUIDE -CAMERA PROBLEM No Video POSSIBLE CAUSE 1. Power Supply: Connections …. -Voltage Range... 2. Video Connections LIKELY SOLUTION Check the input power connections at the terminal block, ensuring no wires are loose. The supply range is: 12-28VAC or 10.5-40VDC. Measure the voltage at the terminal block. Determine if the wiring polarity at the “Video Connector” terminal block is correct. Check BNC connector.
monitor. Check the video signal. If okay, the problem is with the interconnections. If still no video, contact BOSCH Service Center. See rear page of this manual for contact information. Poor Picture Quality Dim Image Snowy Image Iris closed Poor Video Signal Noisy Power Supply - 42 - Increase iris level on lens Ensure the video cable is correctly matched and terminated with 75 ohms at each end. Make sure the video cables are of similar types.
Horizontal Scan Lines, Rolling Up or Down Negative, scrambled, or faded image connections. Relocate or replace the power supply. Ground Looping on video cable Low voltage Check the coax cable shield is not touching “ground”, e.g. at the couplings. An electrically isolated circuit board or isolation transformer may be required. Check voltage at input power cable. Must be >10.5VDC or >12VAC. Video leads reversed connection.
- 44 -
11. TROUBLESHOOTING GUIDE – LEDs PROBLEM Fuse Blows Don’t know if LEDS are “ON” LEDs are not “ON” LEDs are not turning “OFF” when sufficient ambient light is present POSSIBLE SOLUTION - Check the fuse rating. - Check for shorting between the housing and the input power wires. - 850nm LEDs will have a faint red glow when “ON”. 940nm LEDs are covert. - Aim the LEDs directly at an IR sensitive camera, or use a mirror to see the lights through the EX30 camera, or wait for the LEDs to warm up (two minutes).
12. MOUNTING HOLE - DIAGRAM • • All dimensions expressed in millimeters 1.59” X 3.
13. GENERAL SPECIFICATIONS Power Consumption: Maximum Current: 36W Max. 3.0A @12Vdc Input Voltage: 24VAC 12VDC Enclosure (housing): Aluminum casting Viewing Window: Glass Dimensions: 130mm H ( 5.12” ) 134.5mm W ( 5.30” 212mm L ( 8.35” ) Operational Temperatures: 0 0 -50 C to +50 C Weight: 2.2kg (4.9 lbs.) Subject to change without notice.
Note: - 48 -
Americas Bosch Security Systems, Inc. 850 Greenfield Road Lancaster, Pennsylvania 17601 USA Telephone+ 1 888-289-0096 Fax + 1 585-223-9180 Email: security.sales@us.bosch.com www.boschsecurity .us Europe, Middle East, Africa: Bosch Security Systems B.V. P.O. Box 80002 5600 JB Eindhoven, Netherlands Phone: + 31 40 2577 284 Fax: + 31 40 2577 330 emea.securitysystems@bosch.com www.boschsecurity.com Asia Pacific: Bosch Security Systems Pte Ltd.