OBJ_DOKU-7132-001.fm Page 1 Thursday, August 30, 2007 5:09 PM Robert Bosch GmbH Power Tools Division 70745 Leinfelden-Echterdingen www.bosch-pt.com GBH Professional 1 619 929 736 (2007.
OBJ_BUCH-427-001.book Page 3 Thursday, August 30, 2007 4:35 PM 3| B A 9 1 8 X 10 11 10 D C 3 14 13 13 12 E 1 619 929 736 | (30.8.
OBJ_BUCH-427-001.book Page 4 Thursday, August 30, 2007 4:35 PM 4| H G X 8 10 16 15 17 18 J I 19 20 3 21 6 1 619 929 736 | (30.8.
OBJ_BUCH-427-001.book Page 5 Thursday, August 30, 2007 4:35 PM 5| 3 1 2 4 5 6 7 8 9 10 11 1 619 929 736 | (30.8.
OBJ_BUCH-427-001.book Page 16 Thursday, August 30, 2007 4:35 PM 16 | English 4) Power tool use and care a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
OBJ_BUCH-427-001.book Page 17 Thursday, August 30, 2007 4:35 PM English | 17 f Always wait until the machine has come to a complete stop before placing it down. The tool insert can jam and lead to loss of control over the power tool. f Never use the machine with a damaged cable. Do not touch the damaged cable and pull the mains plug when the cable is damaged while working. Damaged cables increase the risk of an electric shock. Functional Description Read all safety warnings and all instructions.
OBJ_BUCH-427-001.book Page 18 Thursday, August 30, 2007 4:35 PM 18 | English Technical Data Rotary Hammer GBH 2-18 E Professional GBH 2-18 RE Professional Article number 3 611 B58 2.. 3 611 B58 3.. Speed control z z – z W 550 550 bpm 0 – 3960 0 – 3960 J 0 – 1.7 0 – 1.7 rpm rpm 450 – 1550 – 450 – 1550 450 – 930 SDS-plus SDS-plus Spindle collar diameter mm 43 (Euro-Norm) 43 (Euro-Norm) Drilling diameter, max.: – Concrete – Steel – Wood mm mm mm 18 13 30 18 13 30 kg 2.0 2.
OBJ_BUCH-427-001.book Page 19 Thursday, August 30, 2007 4:35 PM English | 19 Declaration of Conformity We declare under our sole responsibility that the product described under “Technical Data” is in conformity with the following standards or standardization documents: EN 60745 according to the provisions of the directives 2004/108/EC, 98/37/EC (until Dec. 28, 2009), 2006/42/EC (from Dec. 29, 2009 on). Technical file at: Robert Bosch GmbH, PT/ESC, D-70745 Leinfelden-Echterdingen Dr.
OBJ_BUCH-427-001.book Page 20 Thursday, August 30, 2007 4:35 PM 20 | English Inserting the Key Type Drill Chuck (see figure D) Clean the shank end of the adapter shank and apply a light coat of grease. Insert the key type drill chuck with the adapter shank into the tool holder with a turning motion until it automatically locks. Check the locking effect by pulling the key type drill chuck. Removing the Key Type Drill Chuck Push the locking sleeve 3 toward the rear and pull out the key type drill chuck 13.
OBJ_BUCH-427-001.book Page 21 Thursday, August 30, 2007 4:35 PM English | 21 Adjusting the Drilling Depth on the Dust Extraction Attachment (see figure H) The required drilling depth X can also be adjusted when the dust extraction attachment is mounted. Insert the SDS-plus drilling tool to the stop into the SDS-plus tool holder 1. Otherwise, the movability of the SDS-plus drilling tool can lead to incorrect adjustment of the drilling depth. Loosen the wing bolt 19 on the dust extraction attachment.
OBJ_BUCH-427-001.book Page 22 Thursday, August 30, 2007 4:35 PM 22 | English Safety Clutch f If the tool insert becomes caught or jammed, the drive to the drill spindle is interrupted. Because of the forces that occur, always hold the power tool firmly with both hands and provide for a secure stance. f If the power tool jams, switch the machine off and loosen the tool insert. When switching the machine on with the drilling tool jammed, high reaction torques can occur.
OBJ_BUCH-427-001.book Page 118 Thursday, August 30, 2007 4:35 PM 118 | 1 617 000 132 SDS-plus 1 608 571 062 Ø 1,5 – 13 mm 2 602 025 102 1 613 001 010 1 607 950 045 2 607 000 207 1 607 000 173 2 605 438 524 1 619 929 736 | (30.8.
