Operation Manual

32 | English
1 609 92A 15S | (29.1.15) Bosch Power Tools
22 Fixture for storage of the blade guard
23 Retaining clamp for storage of the angle stop
24 Guide rod of the table extension
25 Stop for 45° bevel angle
26 Locking lever for adjustment of bevel angles
27 Scale for bevel angle
28 Stop for 0° bevel angle
29 Clamping handle for the sliding table
30 V-guide groove on saw table for parallel guide
31 Insert plate
32 Saw blade
33 Sticker for marking of the cutting line
34 Profile rail
35 Guide groove for parallel guide 8
36 Storage for parallel guide 8
37 Hex key (5 mm)
38 Locking screw of the table extension
39 “Auxiliary parallel guide” fastening kit
40 Chip ejector
41 Extraction adapter
42 Cable holder
43 Fastening kit for “table extension”
44 Bottom plate
45 Insert-plate notches
46.1 Clamping lever for locking blade guard 5.1
46.2 Clamping screw for locking blade guard 5.2
47 Clamping handle of the parallel guide
48 V-guide of parallel guide
49 Auxiliary parallel guide
50 Guide rail of the angle stop
51 Knurled screw for locking the angle stop
52 “Profile rail” fastening kit
53 Knurled nut for profile rail
54 Lower saw blade cover
55 Fastening screw of the lower saw blade cover
56 Clamping nut
57 Spindle lock lever
58 Clamping flange
59 Mounting flange
60 Tool spindle
61 Indicator for bevel angle
62 Locking knob for various mitre angles
63 Angle indicator on the angle guide
64 Lens
65 Saw-table clearance indicator
66 ON button
67 Cross-head screw for adjustment of stop
28
68 Screw for bevel angle indicator
69 Cross-head screw for adjustment of stop 25
70 Front hex socket screws (5 mm) for parallelism
adjustment of the saw blade
71 Rear hex socket screws (5mm) for parallelism
adjustment of the saw blade
72 Screw for saw-table clearance indicator
73 Screw for parallel guide clearance indicator
74 Adjusting screws for insert plate
75 Holder for storage of “auxilliary parallel guide fastening
kit”
76 Retaining clamp for storage of the extraction adapter
77 Saw blade storage
78 Holder for storage of the hex key
79 Retaining bracket for storage of the auxiliary parallel
guide
80 Adjustment piece
81 Adjustment screw for tightening tension of guide 48
82 Hex socket screws (5 mm) for parallelism adjustment of
the parallel guide
* depending on country version
Accessories shown or described are not part of the standard deliv-
ery scope of the product. A complete overview of accessories can
be found in our accessories program.
Noise Information
Sound emission values determined according to
EN 61029-2-1.
Typically the A-weighted noise levels of the product are:
Sound pressure level 98 dB(A); Sound power level
111 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under “Technical Data” is in conformity with all rele-
vant provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC including their amendments
and complies with the following standards:
EN 61029-1, EN 61029-2-1.
EC Type Examination No. MSR 1035 by notified testing agen-
cy No. 0366.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 29.01.2015
Henk Becker
Executive Vice President
Engineering
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
OBJ_BUCH-1375-003.book Page 32 Thursday, January 29, 2015 12:34 PM