Installation guide

ManualsBrandsBosch ManualsHome building and DecorGV2 Series

Control Panels

D9412GV2/D7412GV2

Release Notes for Version 7.05 January 2007

Trademarks

Molex

is a registered trademark of Molex Incorporated.

1.0 Requirements

Table 1: Required Handlers

D5200 Handler Version Changes and Notes

GV2MAIN 1.02 New handler for the GV2 Series Control Panels, version 7.05

RADXUSR1 1.06 Updated to support GV2 Series Control Panels

RADXUSR2 1.05 Updated to support GV2 Series Control Panels

RADXPNTS 1.08 Updated to support GV2 Series Control Panels, version 7.05

RADXSKED 1.04 Updated to support GV2 Series Control Panels

GV2AUX 1.02 New handler for the GV2 Series Control Panels, version 7.05

RADXAXS 1.06 Updated to support GV2 Series Control Panels

9000MAIN NA

Not compatible with the GV2 Series Control Panels

RADXAUX1 NA

Not compatible with the GV2 Series Control Panels

During the development of the GV2 Series

Control Panels, some version numbers

were skipped.

The following version numbers were not

released.

GV2MAIN v1.01

RADXUSR1 v1.05

RADXUSR2 v1.04

RADXPNTS v1.07

RADXSKED v1.03

GV2AUX v1.01

RADXAXS v1.05

Table 2: Supporting Literature for D9412GV2/

D7412GV2 with Version 7.05 Firmware

Document Name Part Number*

D9412GV2/D7412GV2 Program

Entry Guide

F01U003636-02

D9412GV2/D7412GV2 Program

Record Sheet

F01U003635-02

D9412GV2/D7412GV2 Operation

and Installation Guide

F01U003641-02

D9412GV2/D7412GV2 Approved

Applications Compliance Guide

F01U003639-02

GV2 Series Program Entry Guide

Supplement for SIA CP-01

Compliance

F01U032733-01

• Older revisions have alphabetic revision identifiers (for

example, F01U003636B) and do not provide information

that supports version 7.05 firmware.

Summary of content (12 pages)

PAGE 1
Control Panels D9412GV2/D7412GV2 Release Notes for Version 7.05 January 2007 Trademarks Molex® is a registered trademark of Molex Incorporated. 1.0 Requirements Table 1: Required Handlers D5200 Handler GV2MAIN RADXUSR1 RADXUSR2 RADXPNTS RADXSKED GV2AUX RADXAXS 9000MAIN RADXAUX1 Version 1.02 1.06 1.05 1.08 1.04 1.02 1.06 NA NA Changes and Notes New handler for the GV2 Series Control Panels, version 7.
PAGE 2
D9412GV2/D7412GV2 • When a Route Group is configured with an IP destination in the primary path and a telephone number in the backup path, a break in the Network Link Integrity now annunciates locally. Refer to Enhanced Communication Trouble on page 6 for more details. • Changes ensure that the D928 primary and secondary phone line failure LEDs operate only when the Phone Supervision interval is enabled. Use an analog telephone line with the D5200. The D5200 dials only pulses.
PAGE 3
D9412GV2/D7412GV2 • Minor corrections improve the user interface for the following function list menus on the D1260 and D1260B Keypads: Table 4: Parameters for Heartbeat Poll Configuration in Version 7.031 Master Arm? Master Arm Instant? Perimeter Arm Delay? Perimeter Arm Inst? Disarm? 2.2 Version 7.03 • Changes allow Custom Functions to operate correctly in the Function List when CC# Menu Lock is set to Yes on the D1260 and D1260B Keypads.
PAGE 4
D9412GV2/D7412GV2 • • • • Corrections now prevent a duress passcode from being accepted by a keypad currently in an area that has A# Duress Enable set to No. If the Duress feature is used, A# Duress Enable should be set to Yes for all areas. The alternate function of Area 6 Silent Alarm Relay parameter was removed. To enable Fire Trouble Resound support, use GV2AUX→MISCELLANEOUS→Fire Trouble Resound. The alternate function of Area 5 Silent Alarm Relay parameter was removed.
PAGE 5
D9412GV2/D7412GV2 Battery Recharge Circuit Monitor 3.0 New Features 3.1 Version 7.05 – UL 864 and ANSI/SIA CP-01 Compliance 3.1.1 UL 864 Compliance Version 7.04 was skipped during development and was not released. Support for D1255RB and D1256RB Keypads, and D1257RB Annunciator The D9412GV2 and D7412GV2 Control Panels, version 7.05 and above, support the new D1255RB and D1256 Keypads and the new D1257RB Annunciator.
PAGE 6
D9412GV2/D7412GV2 Enhanced Communication Trouble The default configuration parameters for the poll rate, ACK wait time, and number of retries complies with UL. Entry Delay Warning Prompt: A# Entry Warning When enabled, the Alarm Bell output pulses ON and OFF for the last ten seconds of the Entry Delay. Exit Time Restart When an Enhanced Communication Trouble condition occurs, it generates a system-wide trouble message (COMM TRBL SDI ##).
PAGE 7
D9412GV2/D7412GV2 Remote Arm/ Disarm Output Swinger Shunt Enhancement Prompt: Remote Warning Prompt: Swinger Count When enabled, this feature uses the Alarm Bell output to annunciate the arming and disarming of an area by remote means, such as by keyswitch, key fob, or remote software (RPS, BIS Security Engine). When arming occurs, the output pulses for two seconds. When disarming occurs, the output pulses ON, OFF, ON, OFF for two seconds each.
PAGE 8
D9412GV2/D7412GV2 3.2.2 New Firmware Features: Two Man Rule: Two Man Rule requires two unique passcodes to be entered at the same keypad to disarm an area. Without the second passcode, the system denies entry. Two Man Rule requires the presence of two people at opening, providing added security. Early Ambush: Early Ambush requires two passcode entries on the same keypad or on two separate keypads located in the same area.
PAGE 9
D9412GV2/D7412GV2 • The battery backed-up RAM now has a SuperCap installed. The Super-Cap maintains power for up to 30 minutes to the control panel’s memory when replacing the lithium battery. In earlier G Series Control Panels, if the coin battery was removed and the control panel was powered down, all configuration was lost. This enhancement allows the control panel to retain its configuration during necessary battery replacement.
PAGE 10
D9412GV2/D7412GV2 Notes D9412GV2/D7412GV2 Release Notes for Version 7.
PAGE 11
D9412GV2/D7412GV2 Notes D9412GV2/D7412GV2 Release Notes for Version 7.
PAGE 12
© 2007 Bosch Security Systems, Inc. 130 Perinton Parkway, Fairport, NY 14450-9199 USA Customer Service: (800) 289-0096; Technical Support: (888) 886-6189 F01U003637-02 Release Notes for Version 7.