Operation Manual
Table Of Contents
- [en] Instruction manual
- Ú Table of contents[en] Instruction manual
- : Important safety information
- Read these instructions carefully. Only then will you be able to operate your appliance safely and correctly. Retain the instruction manual and installation instructions for future use or for subsequent owners.
- This appliance is only intended to be fully fitted in a kitchen. Observe the special installation instructions.
- Check the appliance for damage after unpacking it. Do not connect the appliance if it has been damaged in transport.
- Only a licensed professional may connect appliances without plugs. Damage caused by incorrect connection is not covered under warranty.
- This appliance is intended for domestic use only. The appliance must only be used for the preparation of food and drink. The appliance must be supervised during operation. Only use this appliance indoors.
- This appliance may be used by children over the age of 8 years old and by persons with reduced physical, sensory or mental capabilities or by persons with a lack of experience or knowledge if they are supervised or are instructed by a person responsi...
- Children must not play with, on, or around the appliance. Children must not clean the appliance or carry out general maintenance unless they are at least 8 years old and are being supervised.
- Keep children below the age of 8 years old at a safe distance from the appliance and power cable.
- Always slide accessories into the cooking compartment correctly. See "Description of accessories in the instruction manual.
- Risk of fire!
- Risk of burns!
- Risk of scalding!
- Risk of injury!
- Risk of electric shock!
- ■ Incorrect repairs are dangerous. Repairs may only be carried out by one of our trained after-sales engineers. If the appliance is faulty, unplug the mains plug or switch off the fuse in the fuse box. Contact the after-sales service.
- Risk of electric shock and serious injury!
- Risk of electric shock!
- Risk of electric shock!
- Risk of electric shock!
- Risk of fire!
- Risk of burns!
- Risk of serious damage to health!
- Causes of damage
- Function control knob
- Sensors and display panel
- Sensors to modify the programmed values
- Inside the oven
- Special accessories
- Heating the oven
- Cleaning the accessories
- Type of heating and temperature
- Rapid heating
- Cooking time
- End time
- Time
- 1. Press the 0 sensor.
- 2. Set the time with the @ or A sensors.
- 3. Confirm the time with the 0 sensor.
- 2. Set the time with the @ or A sensors.
- 3. Confirm the time with the 0 sensor.
- 2. Change the basic setting using the @ or A sensors.
- 3. Confirm with the sensor0.
- 4. Finally, press the 0 sensor for approximately 4 seconds.
- Before using the self-clean function
- Setting
- After using the self-clean function
- Light
- Removing and refitting the wire shelves or left and right hand side rails
- Unhooking and hanging the oven door
- : Risk of injuries.!
- Unhooking the door
- 2. Remove both locking levers located on the right and left hand sides (figure A).
- 3. Fully close the oven door as far as possible (figure B). Grip the left and right hand sides of the door with both hands. Close the door slightly more and remove it.
- 2. The bottom groove of the hinges must fit snugly on both sides.
- 3. Reclose the attachment levers (picture C). Close the oven door.
- Removing the door covering
- Removing and installing the door panels
- Removal
- 2. Unscrew the cover at the top of the oven door. To do this, unscrew the left and right screws (fig. A).
- 3. Lift the top panel up and pull it out and remove the two small seals (fig. B).
- 4. Unscrew the retaining clips on the right and left. Lift the panel and remove the clips from the panel (fig. C).
- 5. Remove the seal from the bottom of the panel (fig. D). Pull the seal and remove it up and out. Pull out the panel.
- 6. Pull the lower panel at an angle, upwards and out.
- 7. Do NOT unscrew the left and right-hand screws from the sheet metal part (fig. E).
- 2. Slide in the middle panel (fig. B).
- 3. Stick the retaining clips onto the right and left-hand side of the panel, aligning them so that the retaining carriers are over the screw holes, and then screw into place (fig. C).
- 4. Hook the seal in to the bottom of the panel again (fig. D).
- 5. Insert the uppermost panel at an angle to the back into the brackets. Take care not to push the seal to the back (fig. E).
- 6. Insert the two small seals on the left and right of the panel again (fig. F).
- 7. Put the cover back in place and screw it on.
- Changing the oven bulb
- Protective glass panels
- Saving energy
- Eco hot air function
- Suggestions and practical advice for baking
- Meat, poultry, fish
- Tips for roasting and grilling
- Au gratin, soufflés, toast
- Ready-made products
- Special dishes
- Defrosting
- Drying
- Jam making
- Grilling
14
4. Hook the seal in to the bottom of the panel again (fig. D).
5. Insert the uppermost panel at an angle to the back into the
brackets. Take care not to push the seal to the back (fig. E).
6. Insert the two small seals on the left and right of the panel
again (fig. F).
7. Put the cover back in place and screw it on.
8. Attach the oven door.
Do not use the oven again until the panels have been
correctly installed.
Troubleshooting
Quite often, when there is a malfunction, it is usually a small
irregularity which is easy to rectify. Before contacting the
Technical Assistance Service, try to determine the cause of the
fault using the following table.
Troubleshooting table
Error messages
When the indicator displays an error message with
“, press
the
0 sensor. The message will disappear. The set time
function will be deleted. If the error message does not
disappear, call the Technical Assistance Service.
The following error messages can be solved by the user.
: Risk of electrical discharge and the resulting shock.!
Incorrect repairs can be dangerous. Repairs can only be
carried out by qualified personnel from the Technical
Assistance Service.
'
&
)
(
Fault Possible cause Solution/advice
The oven does
not work.
The fuse has
blown.
Check the condition of the
fuse/circuit breaker in the
fuse box.
Power cut Check that the light in the
kitchen and other house-
hold appliances are work-
ing.
The
0 symbol
lights up on the
display with
some zeros.
Power cut Set the time once again.
The oven does
not work.
There is dust in
the contacts.
Turn the control knob sev-
eral times in both direc-
tions.
The oven door
does not open.
The
H symbol
lights up on the
display panel.
The oven door
has been
locked by the
self-cleaning
function
q.
Wait until the oven has
cooled and the
H symbol
turns off.
The display
shows
”‰.
The appliance
has been auto-
matically turned
off.
Turn the function control
knob to the zero setting.
Error message Possible cause Solution/advice
“‹‚‚
A sensor has
been pressed
for too long or
has got stuck.
Press all the sensors one
by one. Check if a sensor is
stuck, covered or dirty
“‚‹‡
The door lock
has been acti-
vated with the
door open.
Press the
0 sensor. You
can now begin program-
ming again.
“‚‚†
The tempera-
ture inside the
oven is too
high.
The door oven is locked
and heating has stopped.
Wait until the oven has
cooled. Press the
0 sensor
and reset the time.