BOSCH INSTALLATION INSTRUCTION for Bosch Electric Built-in MANUAL Single & Double Oven Models HBL 53..154../55../56.. _3 BEFORE YOU BEGIN, i_z) READ IMPORTANT: INSTALLER: Save THESE these inst.ru, ctions Please OWNER: INSTRUCTIONS for the local leave this manual Please COMPLETELY with owner keep this manual electrical AND inspector's for future for future CAREFULLY reference reference.
Table of Contents INTRODUCTION ....................................................................................................................... 3 Tools You Will Need ................................................................................................................... 3 Power 3 Requirements Choosing .................................................................................................................... Oven Location Steps for Installation TECHNICAL Single .......
INTRODUCTION Please read these instructions COMPLETELY AND CAREFULLY. They will save you time and effort and help to ensure optimum oven performance. Be sure to observe all WARNINGS. These installation instructions are intended for use by a qualified installer. In addition to these instructions the oven shall be installed: • In the United States, in accordance with the National Electric Code/State and Municipal codes and/or local codes. • In Canada, tric Code in accordance with Canadian C22.
TECHNICAL SINGLE DATA OVEN For cutout dimensions Preparing Location Single Oven Models see following sections rifled: Electrical Ratings and Maximum Connected Load Convection Oven Volts Hertz Amperes @240V/208V Watts @240V/208V HBL 532A UC 240/208 60 13.5/13.6 3,250/2,820 No HBL 535A UC 240/208 60 13.5/13.6 3,250/2,820 No HBL 536A UC 2401208 60 13.5/13.6 3,250/2,820 No I"IBL 542A UC 240/208 60 13.5/13.6 3,250/2,820 Yes HBL 545A UC 240/208 60 13.5/13.
UNDERCOUNTER INSTALLATION, i SINGLE Oven eleclflcaJsupply:. Locate Ju_tion b_ in adjacent cabinet or below bottom support surface. I I I I I I [ I I < 28" opening width ) I I I I I I I I I I Bottomsupport sul/eee must be solid, level and able to suppod at leest of 150 Ibs. I I \ I -------t _ sp_ 29-1/4" width of _n 1/4" rain. dlstance between oven door • frame and adjacent doors or drawer fronts. _na door frame maintain minimum spacing as shown.
WALL INSTALLATION, SINGLE OVEN ::_: iSiK_to _ to _t _the Screws i the mounti ho4e_sIn ktn_e frame door to see frame and mounting Do not overtighten screws. Note: Do not slide , oven across age to floor covering suit. floor. Dam- or floor could re- • The oven support surface must be a minimum 3/4" thick plywood platform, solid, level and flush with the bottom of the cabinet cutout• • Use extreme caution when moving installing the oven. it is very heavy. or 4.
WALL INSTALLATION, DOUBLE OVEN Secure oven to cabinet using b_e screws prided. Screws should be inserted through the mounting holes in the positions indicated in the frame (open door to see frame and mounting holes). Do not overtighten screws. Note: Do not slide oven . age to floor covering sult. across floor. Dam- or floor could re- The oven support surface must be a minimum 3/4" thick plywood platform, solid, level and flush with the bottom of the cabinet cutout. . .
ELECTRICAL SUPPLY WIRING Before installing the oven have a qualified electrician verify that your home is provided with ade• quate electrical service and that the addition of the oven will not overload the branch circuit on which it is to be installed. A separate three-wire or four-wire single phase, 240 Volt, 60 Hz., or a 208 Volt, 60 Hz. branch circuit is required. Note: For use with 208 V, 60 Hz supply voltage the wiring must be modified as shown in Connecting to 208 Volt Circuit.
CONNECTING TO 208 V CIRCUIT To connect The ovens are pre-wired for connection to 240 volt, 60 Hertz supply. If connecting to a 208 volt, 60 Hz. supply a jumper must be used across two terminals. For the double oven models there are two jumpers, one for the upper oven and one for the lower oven. For the single ovens there is one jumper. Please jumper refer to figures below for placement for 208 volt, 60 hertz connection. to 208 volt circuit: Remove the access panel(s) located back of the oven(s). 2.
ELECTRICAL This appliances GROUND wire CONNECTIONS 3-WIRE is manufactured with a green connected to the oven chassis. After making sure that the power has been turned • off connect the flexible conduit from the oven to the junction box using a U.L. listed conduit connector. Figures A and B and the instructions provided below present the most common way of connecting the ovens. Your local codes and ordinances, of course, take precedence to these instructions.
FINAL CHECK LIST volt the voltage reading between the black and red wires should be 190 to 208 volts. To prevent improper connections leading to damage of electrical components and so voiding the warranty, the following steps must be performed: 5. Set the time of day by pressing the Set Clock button and pressing the plus (+) or minus (-) button, to the right of the display to set the correct time. Once the time is set depress the Set Clock button to enter the time.