Installation Instruction
Table Of Contents
- _
- en-us
- Table of contents
- 1 IMPORTANT SAFETY INSTRUCTIONS
- 2 Before you begin
- 3 Removing the packaging
- 4 Installation requirements
- 5 Prior to installation
- 6 Electrical connection
- 7 Installing the range into the cabinets
- 8 Testing the operation
- 9 Customer service
- fr-ca
- Table des matières
- 1 IMPORTANTES CONSIGNES DE SÉCURITÉ
- 1.1 Définitions des termes de sécurité
- 1.2 Indications générales
- 1.3 Consignes générales de sécurité
- 1.4 Manipulation sécuritaire des appareils
- 1.5 Lieu d'installation
- 1.6 Codes et normes de sécurité
- 1.7 Sécurité électrique
- 1.8 Mises en garde conformément à la proposition 65 de l'État de Californie
- 1.9 Transport
- 2 Avant de commencer
- 3 Retirer l'emballage
- 4 Exigences d'installation
- 5 Avant l'installation
- 6 Raccordement électrique
- 7 Installer la cuisinière dans les armoires
- 8 Opération d’essai
- 9 Service à la clientèle
- es-mx
- Tabla de contenidos
- 1 INSTRUCCIONES DE SEGURIDAD IMPORTANTES
- 2 Antes de empezar
- 3 Retirar el embalaje
- 4 Requisitos de instalación
- 5 Antes de la instalación
- 6 Conexión eléctrica
- 7 Instalación del electrodoméstico en los gabinetes
- 8 Comprobación del funcionamiento
- 9 Servicio de atención al cliente
Testing the operation en-us
15
3. Keep the drawer assembly level and square to the
housing and gently insert the drawer to the housing, un-
til a slight increase in resistance is felt at the approxi-
mate position shown below.
Notes
¡ A slight side-to-side wiggle motion may be required to
properly get the ball bearings to accurately align.
¡ If more than a moderate force is required to insert the
drawer, remove the drawer and repeat the installation
procedure.
4. Push the drawer in fully. An audible “click” should be
heard when the drawer is properly closed causing the
drawer to lock in the closed position.
Testing the operation
8 Testing the operation
Testing the operation
Check if your unit is working properly after you have com-
pleted the installation steps.
1. Turn on power at the breaker.
2. To test the oven select the Bake mode. See the User
Manual for detailed operating instructions.
3. Verify that the oven light comes on and the oven begins
to preheat.
4. To test the door lock set the Self Clean mode. Confirm
that the door locks when the lock icon appears in the
display.
Customer service
9 Customer service
Customer service
If you have any questions on use, are unable to eliminate
an issue in the appliance yourself, or the appliance needs
to be repaired, please contact our Customer Service.
We will work to find an appropriate solution for you thereby
avoiding unnecessary visits by a service provider.
With any warranty repair, we will make sure your appli-
ance is repaired by a trained authorized service provider
using genuine replacement parts. We use only genuine re-
placement parts for all repairs.
Detailed information on the warranty period and terms of
warranty can be found in the Statement of Limited Product
Warranty, from your retailer, or on our website.
If you contact the Customer Service, you will require the
model number (E-Nr.) and the production number (FD) of
your appliance.
USA:
1-800-944-2904
www.bosch-home.com/us/owner-support/get-support
www.bosch-home.com/us/shop
CA:
1-800-944-2904
www.bosch-home.ca/en/service/get-support
www.bosch-home.ca/en/service/cleaners-and-accessories
9.1 Model number (E-Nr.) and production
number (FD)
You can find the model number (E-Nr.) and the production
number (FD) on the appliance's rating plate.
You can see the rating plate with these numbers when you
open the appliance door.
Making a note of your appliance's details and the Cus-
tomer Service telephone number will enable you to find
them again quickly.
9.2 Rating plate location
Refer to this section to see where the rating plate of your
appliance is located.
¡ on the backside of the drawer front. Open the drawer to
view it.










