Installation Guide
Table Of Contents
- Free standing cooker
- en-us
- Table of contents
- 1 IMPORTANT SAFETY INSTRUCTIONS
- 2 Before you begin
- 3 Installation procedure
- 3.1 How to remove the oven door
- 3.2 Fitting the rear vent trim
- 3.3 Fitting the adjustable feet
- 3.4 Install appliance
- 3.5 Installing the anti-tip bracket
- 3.6 Connect electrical supply
- 3.7 Preparation for power connection
- 3.8 Four-wire range cord connection (recommended method)
- 3.9 Connecting the three-wire range cord (alternate method)
- 3.10 Connecting the four-wire flexible conduit
- 3.11 Connecting the three-wire flexible conduit
- 3.12 Testing the operation
- 4 Customer Service
- 5 Wiring diagrams
- fr-ca
- Table des matières
- 1 IMPORTANTES CONSIGNES DE SÉCURITÉ
- 1.1 Définitions des termes de sécurité
- 1.2 Informations générales
- 1.3 Consignes générales de sécurité
- 1.4 Manipulation sécuritaire des appareils
- 1.5 Lieu d'installation
- 1.6 Codes et normes de sécurité
- 1.7 Sécurité électrique
- 1.8 Mises en garde conformément à la proposition 65 de l'État de Californie
- 1.9 Transport
- 2 Avant de commencer
- 3 Procédure d’installation
- 3.1 Comment retirer la porte du four
- 3.2 Ajustement de la garniture de ventilation arrière
- 3.3 Montage des pieds réglables
- 3.4 Installer l'appareil
- 3.5 Montage de la console anti-basculement
- 3.6 Raccordement à l'alimentation électrique
- 3.7 Préparation à la connexion électrique
- 3.8 Liaison par cordon à quatre fils de la cuisinière (méthode recommandée)
- 3.9 Raccordement du cordon à trois fils de la cuisinière (autre méthode)
- 3.10 Raccordement du conduit électrique flexible à quatre fils
- 3.11 Raccordement du conduit électrique flexible à trois fils
- 3.12 Opération d’essai
- 4 Service à la clientèle
- 5 Schémas de branchement
en-us Installation procedure
10
6. Refit the door in the reverse order in which it was re-
moved.
3.2 Fitting the rear vent trim
1. The rear vent trim is nested in the styrofoam packaging.
Remove the packaging and the protective film from the
rear vent trim. Remove the bag with 2 screws attached
to the rear vent trim.
2. Remove the 2screws from the back trim of the range-
top.
3. Place the rear vent trim on the rangetop frame and fas-
ten it with the 2 screws removed in the previous step.
4. Take the screws from the attached bag and insert and
tighten them from below.
3.3 Fitting the adjustable feet
1. Remove all parts that are not permanently fixed, espe-
cially the pan supports and burners.
2.
CAUTION Protect the floor.
Remove the accessories from the oven.
3.
CAUTION Do not use the door handle or project-
ing control panel for carrying.
Tilt the appliance and put it to the floor on the backside.
4. Screw the adjustable feet into the mounting holes on
the underside of the appliance.
If the appliance needs to be moved again, screw the ad-
justable feet in fully.
5. Carefully move the appliance back onto its feet.