Spec Sheet

For help and assistance with Bosch accessories please visit: www.bosch-eshop.com/eshop/bosch/us or call 1-800-944-2904 Mon-Fri 5am to 6pm PST Sat 6am to 3pm PST
Notes: All height, width and depth dimensions are shown in inches. BSH reserves the absolute and unrestricted right to change product materials and specifications, at any time, without
notice. Consult the product’s installation instructions for final dimensional data and other details prior to making cutout. Applicable product warranty can be found in accompanying product
literature or you may contact your account manager for further details.
Warranties: Bosch warrants that the Product is free from defects in materials and workmanship for a period of three hundred and sixty-five (365) days from the date of purchase. The foregoing
timeline begins to run upon the date of purchase, and shall not be stalled, tolled, extended, or suspended, for any reason whatsoever. This Product is also warranted to be free from cosmetic
defects in material and workmanship (such as scratches of stainless steel, paint/porcelain blemishes, chip, dents, or other damage) to the finish of the Product, for a period of thirty (30) days
from the date of purchase or closing date for new construction. This cosmetic warranty excludes slight color variations due to inherent differences in painted and porcelain parts, as well as
differences caused by kitchen lighting, product location, or other similar factors. This cosmetic warranty specifically excludes any display, floor, “As Is”, or “B” stock appliances.
For more information on our entire line of products, go to www.bosch-home.com/us or call 1-800-944-2904
© BSH Home Appliances Corporation. All rights reserved. Bosch is a registered trademark of Robert Bosch GmbH.
Installation Details
Standard
Flush
Cutout 1
The ovens will overlap the cutout resulting in
a
1
/2" (13mm) spacing between the products
IMPORTANT: The spacing between cutouts applies when installing any Bosch 30" or
27" single, double, combination and 27"/30" compact oven in a side-by-side installation.
Side-by-Side Installation
Cutout 2
Cutout 1 Cutout 2
Standard Flush
Cutout 1
The ovens will overlap the cutout resulting in
a
1
/2" (13mm) spacing between the products
IMPORTANT: The spacing between cutouts applies when installing any Bosch 30" or
27" single, double, combination and 27"/30" compact oven in a side-by-side installation.
Side-by-Side Installation
Cutout 2 Cutout 1 Cutout 2
Standard
Flush
Cutout 1
The ovens will overlap the cutout resulting in
a
1
/2" (13mm) spacing between the products
IMPORTANT: The spacing between cutouts applies when installing any Bosch 30" or
27" single, double, combination and 27"/30" compact oven in a side-by-side installation.
Side-by-Side Installation
Cutout 2
Cutout 1 Cutout 2
Standard Flush
Cutout 1
The ovens will overlap the cutout resulting in
a
1
/2" (13mm) spacing between the products
IMPORTANT: The spacing between cutouts applies when installing any Bosch 30" or
27" single, double, combination and 27"/30" compact oven in a side-by-side installation.
Side-by-Side Installation
Cutout 2 Cutout 1 Cutout 2
09/16
Wall Oven
Speed Oven
Flush Installation
Speed Oven over 27" Single Oven
IMPORTANT: base has to be able to support
oven weight. Please check oven manual for
minimum weight requirements.
required
minimum
between cutouts*
Flush installation requires a base plate
underneath the body: 27" Products - Dimensions:
H
5
/16"(8) x W 25
1
/2"(648) x D 22
1
/2"(571)
800 Series – Stainless Steel HMC87151UC
27" Speed Oven
Standard Installation
27" Speed Oven over Single Oven
Junction box may be located above or
next to the unit within the reach of the
power cord.
Junction box may be located below
(depending on space) or next to the
unit within the reach of the power cord.
Minimum dimension
between cut outs:
• 1" (25mm) for wall oven
cut out height of 28
5
/8"
• 2
5
/8" (67mm) for wall oven
cut out height of 27"
NOTE: Horizontal installation of a 27" oven next to a 27" speed oven with warming
drawer is possible, but the speed oven and warming drawer require either two cutouts or
one cutout with a shelf support in between.