Warming Drawer Models: HWD27, HWD30 i!i_!!i_!_i_iii!i_!i!iii!_i_i_!ii!_!_!_!_!_!i_Ji_i_!!!!!_!_!!_!iii!i_i_ ¸ .......
Table of Contents Safety ...................................... Important Safety Instructions ....................................... Installation .................................. 1 1 3 Before you Begin ................................................. 3 Tools and Parts Needed 3 Parts Included .............................................................. General Information Installation Procedure Service Data Plate ...................................................... 3 ................
Safety Important Safety Instructions READ AND SAVE THESE INSTRUCTIONS WARNING: If the information in this manual is not followed exactly, fire or shock may result causing property damage or personal injury. WARNING: Do not repair or replace any part of the appliance unless specifically recommended in the manuals. Improper installation, service or maintenance can cause injury or property damage. Refer to this manual for guidance. All other servicing should be done by a qualified technician.
Important Safety Instructions READ AND SAVE THESE INSTRUCTIONS Be sure your appliance is properly installed and grounded by a qualified technician. Installation, electrical connections and grounding must comply with all applicable codes. Related Equipment Safety Remove all tape and packaging before using the appliance. Destroy the packaging after unpacking the appliance. Never allow children to play with packaging material. Never modify or alter the construction of the appliance.
Installation Before you Begin Tools and Parts Needed • T-20 6-lobe screwdriver • Measuring tape • Drill with bit (1/8") Parts Included T-20 6-lobe screws, #8xl/2" (8) General Information Power Requirements and Grounding Circuit Specifications: 120V, 15A, 60Hz The outlet must be properly grounded in accordance with all applicable codes.
Cabinet Cutout Dimensions Instructions are based on standard American cabinets 36" (914 mm) high and 24" (609 mm) deep with a 25" (635 mm) countertop. If using non-standard cabinets, alter dimensions accordingly. Cabinet opening bottom must be able to support 110 pounds (50 kg). Allow 3-1/2" (88.9mm) in front 1/2" (12 7mm) [--Frame Overlaps _L 1-1/2" (38 lmm) min. to Fopening above Cab_in_et ....
Dimension Installation Model 27" (685 mm) 30" (762 mm) A 26 3/4" (679 mm) 29 3/4" (755 mm) B 11 1/4" (286 mm) 11 1/4" (286 mm) C 3 5/8" (93 mm) 3 5/8" (93 mm) D 2 3/16" (55 mm) 2 3/16" (55 mm) E 2 5/8" (66 mm) 2 3/4" (69 mm) F 1 5/8" (40 mm) 1 5/8" (40 mm) G 21 1/2" (547 mm) 24 3/8" (618 mm) Procedure Before installing, turn power OFF at the service panel. Lock service AUTION: panel to prevent power from being turned ON accidentally. _ 1. Prepare cabinet cutout.
4. Installwarmingdrawer. It is recommended to have 2 installers to install warming drawer. Failure AUTION: to do so may result in property damage or personal injury. _ Slide warming drawer assembly into cutout until it is flush with cabinet. Secure through four screw holes in front frame (drill pilot holes in cabinet first if necessary). 5. Attach custom drawer front (optional). Use care when handling glass panel to avoid breaking. Broken glass AUTION: could cause injury. _ 6.
If the warming drawer elements or signal light do not turn on, check the power source to see if the circuit breaker is tripped. See Use and Care Manual for troubleshooting the Use and Care Manual. information. Refer to the Warranty in To reach a service representative, see the contact information at the front of the manual. Please be prepared with the information printed on your product data plate when calling. Data Plate The data plate shows the model and serial number.
Notes:
Nnvented for life 5551 McFadden Avenue, Huntington Beach, CA 92649 • 800-944-2904 ° www.boschappliances.com 9000209585 ° 5V0AND ° Rev.
