User guide

ManualsBrandsBosch ManualsHome building and DecorICP-EZM2 Easy Series

Easy Series Intrusion Control Panel

ICP-EZM2

Release Notes October 2006

Release Notes for Firmware Version 2.2

1.0 New Features in Firmware

Version 2.2

• Support for wLSN devices. Contact your local

Bosch representative for wLSN device availability.

• Support for RPS Version 5.4

• Support for DX2010 Input Expander

• Support for up to 32 total input points

(hard-wired, wireless, or combination)

• Support for 26 languages* (refer to Table 1)

Table 1: Supported Languages

Language Voice Module Model Number

Arabic ICP-EZV2-ARF

Bulgarian ICP-EZV2-BGF

Croatian ICP-EZV2-HRF

Czech ICP-EZV2-CSF

Danish ICP-EZV2-DAF

Dutch ICP-EZV2-NLF

English (UK) ICP-EZV2-ENUKF

English (US) ICP-EZV2-ENF

Finnish ICP-EZV2-FIF

Flemish ICP-EZV2-NLBEF

French ICP-EZV2-FRF

German ICP-EZV2-DEF

Greek ICP-EZV2-ELF

Hungarian ICP-EZV2-HUF

Italian ICP-EZV2-ITF

Norwegian ICP-EZV2-NOF

Polish ICP-EZV2-PLF

Portuguese (European) ICP-EZV2-PTF

Romanian ICP-EZV2-ROF

Russian ICP-EZV2-RUF

Serbian ICP-EZV2-SRF

Slovak ICP-EZV2-SKF

Slovenian ICP-EZV2-SLF

Spanish (European) ICP-EZV2-ESF

Swedish ICP-EZV2-SVF

Turkish ICP-EZV2-TRF

* Version 2+ of the control panel requires a

Version 2+ voice module. Refer to Table 1 for

voice module model numbers.

2.0 Fixed Item from Firmware

Version 1.6 to 2.2

Output Activates When Enclosure is Tampered

With: If the EZTS Cover and Wall Tamper Switch is

installed and the control panel enclosure is tampered

with, the appropriate output activates and the control

center announces a tamper message.

3.0 Known Issues in Firmware

Version 2.2

3.1 Control Panel Issues

• Fast Format Using Multiple Report

Destinations: If both report destinations in a

route are used (for example, Route 1 Primary and

Route 1 Backup), and you select Fast Format as

the format option for one destination, you must

select Fast Format for the other destination, too.

When using Fast Format, all enabled reporting

destinations must include a phone number.

Failure to do so might result in a communication

failure.

• Status Announcements during One Button

System Test: To ensure you hear the status of all

tests performed when you press the System Test

button, leave Expert Programming Item 139 (Verbose

System Test Enabled) set to 1.

• English SMS Text for “Point,” “Output,” and

“Key Fob”: “Point,” “Output,” and “Key Fob”

always appear in English in SMS text messages.

• Enabling Installer Passcode From Control

Center with Master User Passcode: Entering

the Master User (User 1) Passcode at the control

center does not enable the Installer Passcode,

even if Expert Programming Item 142 is set to 1. You

should enable the Installer Passcode from the

Phone Menu (recommended), or by presenting

the Master User Token to the control center.

Summary of content (4 pages)

PAGE 1
Easy Series Intrusion Control Panel Release Notes ICP-EZM2 October 2006 Release Notes for Firmware Version 2.2 1.0 New Features in Firmware Version 2.2 2.0 Fixed Item from Firmware Version 1.6 to 2.2 • Support for wLSN devices. Contact your local Bosch representative for wLSN device availability. • Support for RPS Version 5.
PAGE 2
ICP-EZM2 • Route Attempts on Backup Destination: To ensure the system attempts to send reports using the backup destination, do not set Expert Programming Item 305 (Route Attepmts) to a value less than three. • Fire Alarm Not Detected If Preceded By Unrestored Tamper Condition: If a tamper condition occurs on a fire point and it remains unrestored when a fire alarm condition occurs on the same fire point, the fire alarm condition is not detected.
PAGE 3
ICP-EZM2 3.4 Documentation Issues 3.4.1 User Guide Issue • RPS Connection Descriptions Not Accurate: The connections methods described in Section 4.6 Remote Programming Software (RPS) are inaccurate. Below are accurate descriptions. Incorrect LED Indications for Output Options in Key Fob LED Status Table: Wireless key fob LED status indications and output option descriptions are listed below for Firmware Version 2.1: - - 3.4.
PAGE 4
Modem Dial The RPS operator uses a telephone connected in parallel to the RPS modem and clicks the Connect To button in the RPS Panel Communication Window to dial the premises phone number. 1. Connect the internal modem on the RPS PC, or an external modem, to the control panel. Refer to Figure 2. 2. When the control panel answers the incoming call, the system announces “Enter your passcode.” 3.