Data Sheet

ManualsBrandsBosch ManualsBurglar AlarmsFour Channel Quad-Beam Photoelectric Detector

Intrusion Alarm Systems | Photobeam 5000

Photobeam 5000

www.boschsecurity.com

u Quad beam detection

u Environmental discrimination circuit

u Beam power control to reduce cross-talk

The Photobeam 5000 Series consists of the single

channel quad beam ISC-FPB1-W60QS, ISC-FPB1-

W120QS, ISC-FPB1-W200QS, and the four channel

quad beam ISC-FPB1-W60QF, ISC-FPB1-W120QF, and

ISC-FPB1-W200QF detectors with separate

transmitters and receivers.

The detector series uses four pulsed infrared beams

that are designed to activate an alarm when all four

beams are simultaneously blocked. False alarm

immunity is increased by the utilization of four beams

compared to single or dual beam models.

The detector series also features interlocked upper

and lower beams, signal voltage LED, and optional

environmental discrimination circuitry.

System overview

Consisting of a separate transmitter and receiver, it is

designed to activate an alarm when an intruder passes

within the direct line of sight between the transmitter

and receiver.

Functions

Mounting features

Mounting and installing the detector is now easier

than ever. Install the detector through easy-to-use

mounting hole locations which provide an enlarged

entry point of access to accept small to large, single or

multiple cable set wires. Fastening screw locations

eliminate the need for unnecessary crawling or

bending during installation.

Multiple Channel Operation (4-channel models only)

Configure the detectors for up to four different

channels. This allows multiple units to be used near

one another without the possibility of receiver cross-

talk. This is particularly useful when stacking multiple

beam sets.

High Density mode (4-channel models only)

The High Density mode allows you to add an additional

zones of protection to detect larger objects that only

partly interrupt the beams of individual devices. This

feature allows an alarm condition to be generated

when beam pairs are interrupted on adjacent devices

but not all four beams are interrupted on one device.

Summary of content (5 pages)

PAGE 1
Intrusion Alarm Systems | Photobeam 5000 Photobeam 5000 www.boschsecurity.com The Photobeam 5000 Series consists of the single channel quad beam ISC-FPB1-W60QS, ISC-FPB1W120QS, ISC-FPB1-W200QS, and the four channel quad beam ISC-FPB1-W60QF, ISC-FPB1-W120QF, and ISC-FPB1-W200QF detectors with separate transmitters and receivers. The detector series uses four pulsed infrared beams that are designed to activate an alarm when all four beams are simultaneously blocked.
PAGE 2
| Photobeam 5000 Selectable AND/OR mode (4-channel models only) This feature allows an added level of detection by generating an alarm when four beams from two units are blocked simultaneously. Environmental conditions require higher false alarm tolerance against smaller objects passing through the detector's line of sight. To do this, set the AND/OR gate option to AND gate mode that only causes an alarm condition when all four infrared beams are interrupted simultaneously.
PAGE 3
| Photobeam 5000 Power requirements ISC-FPB1-W120QS ISC-FPB1W60QS ISC-FPB1W120QS 90 mA 95 mA Current draw ISC-FPB1W200QS 100 mA * Single channel quad beam series ISC-FPB1W60QF Current draw ISC-FPB1W120QF 120 mA 124 mA ISC-FPB1W200QF 128 mA * Four channel quad beam series Voltage 10.5 VDC to 28 VDC. Alarm output Form C relay (COM, NC, NO) (dry contact) Duration – 2 sec Single channel quad-beam photoelectric detector designed for indoor and outdoor applications.
PAGE 4
| Photobeam 5000 ISC-FPB1-W60QS MP3 L‑Curved Metal Pole Single channel quad-beam photoelectric detector designed for indoor and outdoor applications. Consisting of a separate transmitter and receiver. 60 m (196 ft) max outdoor range, 120 m (393 ft) max indoor range. Curved metal poles for mounting to vertical surfaces for pole mounting photoelectric detectors. Shipped in packages of two.
PAGE 5
| Photobeam 5000 Represented by: Americas: Bosch Security Systems, Inc. 130 Perinton Parkway Fairport, New York, 14450, USA Phone: +1 800 289 0096 Fax: +1 585 223 9180 security.sales@us.bosch.com www.boschsecurity.us Europe, Middle East, Africa: Bosch Security Systems B.V. P.O. Box 80002 5617 BA Eindhoven, The Netherlands Phone: + 31 40 2577 284 Fax: +31 40 2577 330 emea.securitysystems@bosch.com www.boschsecurity.