Installation manual

ManualsBrandsBosch ManualsHome building and DecorLTC-0485-21

Dinion

– LT C 0 610 & LT C 0 4 8 5 s e r i e s c a m e r a s

Installation Instructions

15-bit digital color camera

Manuel d’installation

Caméra numérique couleur

15 bits

Installationshandbuch

15-Bit digitale Farbkamera

Installatiehandleiding

15-bits digitale kleurencamera

Manual de instalación

Cámara digital en color de

15 bits

Manuale di installazione

Telecamera digitale a colori

15 bit

Manual de Instalação

Câmara digital policromática

de 15 bits

安装说明

15 位数码彩色摄像机

DinionXFFrontPage.fm Page 1 Friday, January 21, 2005 4:13 PM

Summary of content (31 pages)

PAGE 1
DinionXFFrontPage.
PAGE 2
PAGE 3
DinionXF | Installation Manual EN | 3 SAFETY PRECAUTIONS Danger The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product's enclosure that may be of sufficient magnitude to constitute a risk to persons.
PAGE 4
DinionXF | Installation Manual EN | 4 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. Both the wide blade and the third prong are provided for your safety. If the supplied plug does not fit into your outlet, consult an electrician for advice. 10.
PAGE 5
DinionXF | Installation Manual EN | 5 FCC Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 6
DinionXF | Installation Manual EN | 6 Introduction The DinionXF is a high-performance smart surveillance color camera. It incorporates 15-bit digital signal processing for outstanding picture performance under all lighting conditions. The DinionXF is easy to install and ready to use, and offers the best solution for demanding scene conditions.
PAGE 7
DinionXF | Installation Manual EN | 7 Unpacking Unpack carefully and handle the equipment with care. The packaging contains: • DinionXF camera • CCD protection cap • Spare lens connector (male) • These instructions Note If equipment appears to have been damaged during shipment, repack it in the original packaging and notify the shipping agent or supplier. Bosch Security Systems | 2003-10 | V0.
PAGE 8
DinionXF | Installation Manual EN | 8 Connections Power Low voltage versions VIDEO VIDEO 10mm High voltage versions DC 12V AC 24V SVHS SVHS SYNC SYNC ALARM ALARM For low voltage cameras: • push in the tabs to open the quick-connectors (these connections are not polarity sensitive). • use AWG16 to 22 stranded wire or AWG16 to 26 solid wire; cut back 10mm (0.4") of insulation. Composite video VIDEO VIDEO DC 12V AC 24V SVHS SYNC SVHS ALARM Bosch Security Systems | 2003-10 | V0.
PAGE 9
DinionXF | Installation Manual EN | 9 Sync VIDEO VIDEO DC 12V AC 24V SVHS SYNC SVHS SYNC ALARM ALARM Y/C VIDEO VIDEO DC 12V AC 24V SVHS SVHS SYNC SYNC ALARM Pin Y/C socket 1 GND Y 2 GND C 3 Y 4 C Bosch Security Systems | 2003-10 | V0.
PAGE 10
DinionXF | Installation Manual EN | 10 Alarm connector Pin Alarm Alarm socket 1 Ground 2 Alarm in 3 Relay out contact 1 4 Relay out contact 2 Pin 1 • • • • • • Pin 4 Max. wire diameter AWG 22-28 for both stranded and solid Default relay position n.o. (normally open), no alarm Alarm output relay switching capability: Max voltage 30VAC or +40VDC. Max 0.5 A continuous, 10VA. Alarm in: TTL logic, +5V nominal, +40VDC max, DC coupled with 22kΩ pull-up to +3.
PAGE 11
DinionXF | Installation Manual EN | 11 Bosch Bosch Pin Video iris lens 1 Supply (11.5V ±0.5, 50mA max.) DC iris lens Damp - 2 Not used Damp + 3 Video signal 1Vpp 1kOhm Drive + 4 Ground Drive - Note If a short circuit is detected on the lens connector, the on-screen display (OSD) failure message LENS SHORT CIRCUIT is shown. The lens circuit is automatically disabled to avoid internal damage. Remove the lens connector and check the pin connections. Bosch Security Systems | 2003-10 | V0.
PAGE 12
DinionXF | Installation Manual EN | 12 Back focus adjustment To optimize picture sharpness in both bright and low-level lighting, adjust the back focus. Use the camera's unique Lens Wizard (see Advanced Setup). This ensures that the object of interest always remains in focus even when focusing at the maximum lens opening. When back focusing vari-focus lenses, adjust to obtain a sharp picture in both wide-angle and tele positions for both far and near focus.
PAGE 13
DinionXF | Installation Manual EN | 13 Mounting the camera The camera can be mounted from the top or bottom. The bottom mounting is isolated from ground. With outdoor scenes, a DC-iris lens is recommended. Caution Do not point the camera/lens into direct sunlight. Bosch Security Systems | 2003-10 | V0.
PAGE 14
DinionXF | Installation Manual EN | 14 Advanced Set-up The DinionXF normally provides an optimal picture without the need for further adjustments. However, advanced set-up options are available for getting the best results from the camera under special circumstances. There are two main menus; a Mode menu and an Installer menu. The camera has three pre-programmed operating modes that can be selected in the Mode menu.
PAGE 15
DinionXF | Installation Manual EN | 15 Menu Structure MODE ALC ENHANCE COLOR BLC VMD MODE ID DEFAULTS MODE x ALC ALC LEVEL SHUT/GAIN PEAK / AVERAGE ALC SPEED MODE X ENHANCE AUTO BLACK BLACK LEVEL CONTOUR DNR XF-DYNAMIC MODE X COLOR WHITE BALANCE WBSPEED R GAIN G-GAIN B-GAIN SATURATION MODE X BLC BLC BLC LEVEL BLC AREA MODE X VMD VMD AREA ACTIVE MOTION SENSITIVITY MODE X DEFAULTS CONFIRM Bosch Security Systems | 2003-10 | V0.
PAGE 16
DinionXF | Installation Manual INSTALL LENS WIZARD I/O SYNC CAMERA ID DEFAULTS EN | 16 INSTALL LENS WIZARD LENS TYPE DETECTED SET BACK FOCUS SET LEVEL INSTALL I/O SYNC INPUT COMMUNICATION CABLE COMP COMP LEVEL ALARM INSTALL SYNC SYNC DETECTED SYNC V PHASE H PHASE SUB PHASE INSTALL CAMERA ID CAMERA ID ID POSITION MAC ADDRESS ALL DEFAULTS CONFIRM Bosch Security Systems | 2003-10 | V0.
PAGE 17
DinionXF | Installation Manual EN | 17 Hints for menu navigation How to use the 5 keys Up key Menu/select key Right key Left key Lock Down key • • Press the menu/select key to access the menus or to move to the next or previous menu. Press the menu/select key for approximately 1.5 seconds to open the Installer menu. • • Use the up or down keys to scroll up or down through a menu. Use the left or right keys to move through options or to set parameters.
PAGE 18
DinionXF | Installation Manual EN | 18 Mode menu Function Selection Description MODE 1, 2, 3 Select operating mode ALC Select submenu Select to access the video level control menu ENHANCE Select submenu Select to access the picture enhancement menu COLOR Select submenu Select to access the color control menu BLC ON, OFF, Select submenu • To enable Back Light Compensation (BLC) operation set to ON • Select to access the BLC menu VMD OFF, SIL, OSD Select submenu • To enable Video Motion
PAGE 19
DinionXF | Installation Manual EN | 19 ALC --> Shutter/Gain submenu Function Selection Description SHUTTER AES, FL, FIXED • AES - auto-shutter - the camera automatically sets the optimum shutter speed for manual iris lenses • FL - flickerless mode avoids interference from light sources (recommended for use with video iris or DC iris lenses only) • FIXED - allows a user defined shutter speed DEFSHUT 1/60 (1/50), 1/100, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/5000, 1/10K Only available if SHUTTER is
PAGE 20
DinionXF | Installation Manual EN | 20 Note If SENS UP or NIGHTSENSE is active, some noise or spots may appear in the picture. This is normal camera behavior. SENS UP may cause some motion blur on moving objects. If GAIN is set to FIXED, NIGHTSENSE will not become active. If NIGHTSENSE is active, all color related menu items are disabled and cannot be accessed.
PAGE 21
DinionXF | Installation Manual EN | 21 BLUE gain -5 - 0 - +5 • ATW mode and AWB hold mode: adjusts the B gain to optimize around the white point. RED GREEN BLUE -50 - 0 - +50 Controls all the colors individually for manual white balance only. SAT -15, … , 0 , … +5 Adjusts the color saturation.
PAGE 22
DinionXF | Installation Manual EN | 22 AREA 1, 2, 3, 4, Select submenu • It is possible to set 4 motion sensitive areas (per MODE). • Press SELECT to enter the area set-up menu. ACTIVE ON, OFF Every area can be enabled individually by selecting YES. MOTION Press SELECT to reset indicator Indicates the peak of measured motion in the selected area SENS Use the LEFT/RIGHT keys to set the SENSitivity for motion to the desired level. Motion above this level triggers alarm.
PAGE 23
DinionXF | Installation Manual EN | 23 Installer Settings Install menu Function Selection Description LENS WIZARD Select submenu Select to optimize camera lens combination I/O Select submenu Select to access the I/O functions SYNC Select submenu Select to access the synchronization functions CAMERA ID Select submenu Select to access ID menu DEFAULTS Return all settings for all modes to factory defaults Select submenu EXIT Exit the menu Install lens wizard submenu Function Selection De
PAGE 24
DinionXF | Installation Manual EN | 24 Adjustment procedure Manual-iris Lens: 1. Unlock the back focus locking button. 2. Adjust the lens to the maximum lens opening. 3. Turn the back focus adjustment as required. 4. Lock the back focus locking button. Adjustment procedure Video-iris Lens: 1. Unlock the back focus locking button. 2. Access the Lens Wizard menu. 3. SET BACK FOCUS NOW is highlighted in the menu. 4. Turn the back focus adjustment as required. 5. Lock the back focus locking button. 6.
PAGE 25
DinionXF | Installation Manual EN | 25 Install I/O --> Alarm submenu Function Selection ACTIVE NONE, HIGH, LOW Selects active_HIGH or active_LOW for the alarm input connector. Select NONE to disable alarm switching. ACTION NONE, MODE1, MODE2, MODE3 Selects the operating mode of the camera upon switching the alarm input. ALARM OUT VMD, REMOTE Select VMD to close the output relay upon VMD alarms. Select REMOTE to make the output relay available to remote communication devices.
PAGE 26
DinionXF | Installation Manual EN | 26 Install ID submenu Function Selection CAMERA ID ID POS Description Enter a 16 character camera name string. Use LEFT/RIGHT to change position in the string, use UP/DOWN to select the character. Use SELECT to exit the string edit screen. OFF, TOP, BOT EXIT Select TOP to display the camera ID in the upper left corner; select BOT for the lower left corner. The ID string is not displayed when the OSD menus are open.
PAGE 27
DinionXF | Installation Manual EN | 27 Technical specification 1/2" CCD versions Type number LTC 0610/11 LTC 0610/21 LTC 0610/51 LTC 0610/61 Standard PAL NTSC PAL NTSC Active pixels 752x582 768x492 752x582 768x492 Rated supply voltage 24 VAC or 12 VDC 12-28 VAC (50/60 Hz) 12-36 VDC Min illumination 0.18 lx 0.
PAGE 28
DinionXF | Installation Manual EN | 28 All versions NightSense On, Off, Auto Sens Up Adjustable from OFF to 10x Auto black On, Off selectable AGC AGC on or off (0 dB) selectable.
PAGE 29
DinionXF | Installation Manual EN | 29 Accessories Power transformers • • • • TC1334 TC120PS TC220PSX-24 TC220PS 120VAC, 60Hz 120VAC, 60Hz 220-240VAC, 50/60Hz 220-240VAC, 50/60Hz - 24VAC, 30VA 15VDC, 9VA 24VAC, 30VA 15VDC, 9VA Interface box: • VP-CFGSFT Bilinx™ communication interface box and software Recommended lenses Varifocal lenses: • LTC 3264/30 • LTC 3274/40 • LTC 3364/21 • LTC 3364/31 • LTC 3364/40 • LTC 3374/20 Zoom lenses: • LTC 3283/20 • LTC 3384/21 1/2" DC-iris, 1/2" DC-iris, 1/3" DC-
PAGE 30
DinionXF | Installation Manual Bosch Security Systems | 2003-10 | V0.
PAGE 31
Bosch Sicherheitssysteme GmbH Ludwig-Bölkow-Allee 85521 Ottobrunn Germany www.bosch-sicherheitssysteme.de © 2003 Bosch Security Systems B.V. Subject to change. Printed in Portugal. 3122 165 23051 Bosch Security Systems B.V. P.O. Box 80002 5600 JB Eindhoven The Netherlands www.boschsecuritysystems.