User manual

EN
|
18
Bosch Security Systems | March 17, 2009
LTC 8900 | User Manual | Keyboard User Functions
6.1.13 User Function 12 -
Default All Monitor Overlays
User Function 12 can be used by users with the priority
level 1, to reset all monitor overlays to default
characteristics (bottom center of screen), and full
brightness. After entering the mode, press ENTER to
reset all monitor overlays. If using the LTC 8555 Series
keyboard, press USER to exit.
6.1.14 User Function 13 -
Print System Configuration Tables
Users with priority level 1 can use this function to print
the contents of the tables programmed. Move the
joystick up and down to select a table, then press
ENTER to send it to the printer port. If using the
LTC 8555 Series keyboard, press USER to exit.
6.1.15 User Function 14 -
Reserved Function
6.1.16 User Function 15 -
System Reset
The system may be reset from the keyboard by users
with priority level 1. After entering this mode, the
video monitor screen indicates RESET SYSTEM. Enter
the password via the numeric keypad, and press
ENTER. The system will then reset. If using the
LTC 8555 Series keyboard, press USER to exit the
mode without resetting the system.
NOTE: The system should be reset whenever a change
is made on the main CPU module s DIP switches.
Alternatively, the main power to the CPU bay may be
switched off for 10 seconds, then restored. Depending
on the size and complexity of the system, several
seconds may elapse before operation is restored, due to
the number of initialization tasks being performed.
This is normal.
61.17 User Function 16 -
Time Event Enable/Disable
Users with priority level 1 can use this function to
enable or disable any of the programmed time event
functions. Up to 128 time event functions can be
programmed with the MCS software. Moving the
joystick up/down steps through a table of the 128 time
events. If an event has been programmed, moving the
joystick to the right enables the event, and to the left
disables it. The current status of an enabled time event
is displayed by this user function.
6.1.18 User Function 17 -
Set Monitor ID
User Function 17 can be used by users with the priority
level 1, to enter a (12-character) monitor identification
message for display in the top line of the monitor
overlay display on any system monitor(s). This monitor
title will be visible on the display regardless of the
camera currently being viewed. This message can be
used to identify the particular monitor or a group of
cameras assigned to this monitor. Refer to SECTION 8,
LTC 8900 CHARACTER SET, for the available
characters. After entering the mode, the joystick is
moved right/left to select the character to be changed.
The selected character is identified by a box with a
question mark inside. The first line of the video monitor
display indicates the code number of the character
selected. Move the joystick up/down to step through
the CHARACTER SET table, or enter the character s
number (identified in the Tables) via the numeric
keypad, then press ENTER. Once the monitor title
has been set, press ENTER to store it to memory. If
using the LTC 8555 Series keyboard, press USER to
exit the mode. The user may select between this
monitor message and the status display by using the
User 5 Function described above.
61.19 User Function 18 -
Print Sequence
Use this function to print the contents of a
programmed sequence. Users with priority level 1 can
use the joystick to select the desired sequence, then
press ENTER to print it to the printer port. Only those
sequences currently existing in memory will be shown
in the list. If using the LTC 8555 Series keyboard, press
USER to exit.
6.1.20 User Function 19 -
Select Alarm Response
Users with the priority level 1 can use this function to
reset the system alarm configuration tables to one of
these predefined alarm response modes: BASIC,
AUTOBUILD, or SEQUENCE & DISPLAY. Move the
joystick up/down to select the desired mode, then
enter your user password on the numeric keypad, and
press ENTER to update the alarm system. If using the
LTC 8555 Series keyboard, press USER to exit.