Installation Manual
Table Of Contents
- Title Page
- Table of Contents
- Safety
- Unpacking
- Introduction
- System Components
- LTC 8904 Series CPU Bay
- LTC 8901 Series CPU Bay
- LTC 8902 Series Output Bay
- LTC 8903 Series Input Bay
- LTC 8934/00 Video Output Modules
- LTC 8921/00 Video Input Modules
- LTC 8943/95 System Controller PC
- LTC 8944/93 and LTC 8945/93 LAN Switches
- LTC 8946/93 LAN Switches
- LTC 8809/00 Video Ribbon Cable
- LTC 8808/00 Video Interconnect Panel
- LAN Cables
- Security Key for PC-based Software
- Miscellaneous Components
- Hardware Installation Procedure for Standard Systems Utilizing LTC 8904 Series CPU
- General Installation Considerations
- LTC 8904 Series CPU Bay Installation
- LAN Switch Installation
- LTC 8902 Series Output Bay and LTC 8903 Series Input Bay Installation
- Module Insertion
- Data Receiver Modules
- LTC 8916/01 Data Receiver Modules
- LTC 8918/01 Data Receiver Modules
- LTC 8934/00 Video Output Modules
- LTC 8921/00 Video Input Modules
- System Video Connections
- Termination Practices
- System Data Connections
- Main Power Connections
- Hardware Installation Procedure for Redundant System Configuration Utilizing LTC 8901 Series CPU
- System Redundancy Considerations
- Main CPU Bay Installation
- LAN Switch Installation
- LTC 8943/95 System Controller PC Installation
- LTC 8902 Series Output Bay and LTC 8903 Series Input Bay Installation
- Module Insertion
- Data Receiver Modules
- LTC 8916/01 Data Receiver Modules
- LTC 8918/01 Data Receiver Modules
- LTC 8934/00 Video Output Modules
- LTC 8921/00 Video Input Modules
- System Video Connections
- Termination Practices
- System Data Connections
- Main Power Connections
- LTC 8901 Series CPU Relay Outputs and Buzzers
- LTC 8901 Series CPU Selection Switch
- Camera Phasing and Accessory Installation
- Satellite System Configuration Installations
- Allegiant Satellite System Configuration Installations
- Satellite Site “Trunk Line” Monitor Outputs
- Main Site “Trunk Line” Video Inputs
- Control Data Lines in Satellite Systems
- Satellite Sites Programming Requirements
- Main Site Programming Requirements
- Special Programming for “Cascaded” Satellite System Configurations
- Alarm Inputs in Satellite Systems
- Troubleshooting Guide
- Maintenance Information
- Pinouts
- Back Page
Pinouts
B.1 LTC 8900 Series CPU Bay Rear Panel
Connector Pinouts
B.1.1 Console Port RS-232 Pinouts
Pin # . . . . . . . . . . . . . . . . . . . .Designation
1 . . . . . . . . . . . . . . . . . . . . . . . .GND
2 . . . . . . . . . . . . . . . . . . . . . . . .Rx
3 . . . . . . . . . . . . . . . . . . . . . . . .Tx
4 . . . . . . . . . . . . . . . . . . . . . . . .CTS
5 . . . . . . . . . . . . . . . . . . . . . . . .RTS
6 . . . . . . . . . . . . . . . . . . . . . . . .GND
7 . . . . . . . . . . . . . . . . . . . . . . . .GND
8 . . . . . . . . . . . . . . . . . . . . . . . .GND
9 . . . . . . . . . . . . . . . . . . . . . . . .GND
B.1.2 Alarm Port RS-232 Pinouts
Pin # . . . . . . . . . . . . . . . . . . . .Designation
1 . . . . . . . . . . . . . . . . . . . . . . . .RTS
2 . . . . . . . . . . . . . . . . . . . . . . . .Tx
3 . . . . . . . . . . . . . . . . . . . . . . . .GND
4 . . . . . . . . . . . . . . . . . . . . . . . .GND
5 . . . . . . . . . . . . . . . . . . . . . . . .GND
6 . . . . . . . . . . . . . . . . . . . . . . . .Rx
7 . . . . . . . . . . . . . . . . . . . . . . . .CTS
8 . . . . . . . . . . . . . . . . . . . . . . . .+12 VDC
9 . . . . . . . . . . . . . . . . . . . . . . . .GND
B.1.3 Keyboard RS-485 Ports
Pin # . . . . . . . . . . . . . . . . . . . .Designation
1 . . . . . . . . . . . . . . . . . . . . . . . .GND
2 . . . . . . . . . . . . . . . . . . . . . . . .GND
3 . . . . . . . . . . . . . . . . . . . . . . . DATA
4 . . . . . . . . . . . . . . . . . . . . . . . . +DATA
5 . . . . . . . . . . . . . . . . . . . . . . . .GND
6 . . . . . . . . . . . . . . . . . . . . . . . . +12 VDC
B.1.4 Primary and Backup Controller Port RS-232
Pinouts
Pin # . . . . . . . . . . . . . . . . . . . .Designation
1 . . . . . . . . . . . . . . . . . . . . . . . .GND
2 . . . . . . . . . . . . . . . . . . . . . . . .Rx
3 . . . . . . . . . . . . . . . . . . . . . . . .Tx
4 . . . . . . . . . . . . . . . . . . . . . . . .CTS
5 . . . . . . . . . . . . . . . . . . . . . . . .RTS
6 . . . . . . . . . . . . . . . . . . . . . . . .GND
7 . . . . . . . . . . . . . . . . . . . . . . . .GND
8 . . . . . . . . . . . . . . . . . . . . . . . .GND
9 . . . . . . . . . . . . . . . . . . . . . . . .GND
B.1.5 Biphase Port Pinouts
Pin # . . . . . . . . . . . . . . . . . . . .Designation
1 . . . . . . . . . . . . . . . . . . . . . . . . +DATA
2 . . . . . . . . . . . . . . . . . . . . . . . . DATA
3 . . . . . . . . . . . . . . . . . . . . . . . .GND
4 . . . . . . . . . . . . . . . . . . . . . . . .GND
5 . . . . . . . . . . . . . . . . . . . . . . . .GND
6 . . . . . . . . . . . . . . . . . . . . . . . .No Connection
7 . . . . . . . . . . . . . . . . . . . . . . . .No Connection
8 . . . . . . . . . . . . . . . . . . . . . . . .GND
9 . . . . . . . . . . . . . . . . . . . . . . . . +12 VDC
B.1.6 COMM PORT 1 and COMM PORT 2
Pin # . . . . . . . . . . . . . . . . . . . . . .Designation
1 . . . . . . . . . . . . . . . . . . . . . . . . . .NC
2 . . . . . . . . . . . . . . . . . . . . . . . . . . +TXD
3 . . . . . . . . . . . . . . . . . . . . . . . . . . TXD
4 . . . . . . . . . . . . . . . . . . . . . . . . . . +RXD
5 . . . . . . . . . . . . . . . . . . . . . . . . . . RXD
6 . . . . . . . . . . . . . . . . . . . . . . . . . .GND
7 . . . . . . . . . . . . . . . . . . . . . . . . . .NC
8 . . . . . . . . . . . . . . . . . . . . . . . . . .NC
9 . . . . . . . . . . . . . . . . . . . . . . . . . .NC
B.1.7 Primary and Backup LAN Ports
Pin # . . . . . . . . . . . . . . . . . . . . . .Designation
1 . . . . . . . . . . . . . . . . . . . . . . . . . . +TD
2 . . . . . . . . . . . . . . . . . . . . . . . . . . T D
3 . . . . . . . . . . . . . . . . . . . . . . . . . . +RD
4 . . . . . . . . . . . . . . . . . . . . . . . . . .No Connection
5 . . . . . . . . . . . . . . . . . . . . . . . . . .No Connection
6 . . . . . . . . . . . . . . . . . . . . . . . . . . R D
7 . . . . . . . . . . . . . . . . . . . . . . . . . .No Connection
8 . . . . . . . . . . . . . . . . . . . . . . . . . .No Connection
B.1.8 Relay Connector (LTC 8901 only)
1 & 2 . . . . . . . . . . . . . . . . . . . . . . .Relay - Primary Power Supply Fault
3 & 4 . . . . . . . . . . . . . . . . . . . . . . .Relay - Primary CPU Fault
5 & 6 . . . . . . . . . . . . . . . . . . . . . . .Relay - Backup Power Supply Fault
7 & 8 . . . . . . . . . . . . . . . . . . . . . . .Relay - Backup CPU Fault
9 & 10 . . . . . . . . . . . . . . . . . . . . . .Relay - Any Fault
11 & 12 . . . . . . . . . . . . . . . . . . . .Input - Silence Buzzer
B.1.9 Console Cable
The LTC 8506/00 cable that connects the Allegiant s CPU
CONSOLE Port to an external PC uses the following pinouts:
9-pin Male Allegiant 9-pin Female
(CONSOLE) Designation (PC Side)
1 GN None
2 Receive Dat 3
3 Transmit Dat 2
4 CTS 1
5 RTS 8
6 GND None
7 GND 5
8 GND None
9 GND None
(Pins 4 & 6 jumpered)
(Pins 1 & 7 jumpered)
A.1.10 Printer Cable
The cable that connects the Allegiant s CPU
CONSOLE port to a standard serial printer uses the
following pinouts:
9-pin Male Allegiant 25-pin Female
(CONSOLE) Designation (Printer Side)
1 GND 1
2 Receive Data 2
3 Transmit Data 3
4 CTS 4, 8
5 RTS 5
6 GND None
7 GND 7
8 GND None
9 GND None
(Pins 6 & 20 jumpered)
11
108 en | Pinouts LTC 8900 Series
2016.04 | 10.7 | F.01U.323.096 Installation Manual Bosch Security Systems, Inc.