Installation Manual
Table Of Contents
- Title Page
- Table of Contents
- Safety
- Unpacking
- Introduction
- System Components
- LTC 8904 Series CPU Bay
- LTC 8901 Series CPU Bay
- LTC 8902 Series Output Bay
- LTC 8903 Series Input Bay
- LTC 8934/00 Video Output Modules
- LTC 8921/00 Video Input Modules
- LTC 8943/95 System Controller PC
- LTC 8944/93 and LTC 8945/93 LAN Switches
- LTC 8946/93 LAN Switches
- LTC 8809/00 Video Ribbon Cable
- LTC 8808/00 Video Interconnect Panel
- LAN Cables
- Security Key for PC-based Software
- Miscellaneous Components
- Hardware Installation Procedure for Standard Systems Utilizing LTC 8904 Series CPU
- General Installation Considerations
- LTC 8904 Series CPU Bay Installation
- LAN Switch Installation
- LTC 8902 Series Output Bay and LTC 8903 Series Input Bay Installation
- Module Insertion
- Data Receiver Modules
- LTC 8916/01 Data Receiver Modules
- LTC 8918/01 Data Receiver Modules
- LTC 8934/00 Video Output Modules
- LTC 8921/00 Video Input Modules
- System Video Connections
- Termination Practices
- System Data Connections
- Main Power Connections
- Hardware Installation Procedure for Redundant System Configuration Utilizing LTC 8901 Series CPU
- System Redundancy Considerations
- Main CPU Bay Installation
- LAN Switch Installation
- LTC 8943/95 System Controller PC Installation
- LTC 8902 Series Output Bay and LTC 8903 Series Input Bay Installation
- Module Insertion
- Data Receiver Modules
- LTC 8916/01 Data Receiver Modules
- LTC 8918/01 Data Receiver Modules
- LTC 8934/00 Video Output Modules
- LTC 8921/00 Video Input Modules
- System Video Connections
- Termination Practices
- System Data Connections
- Main Power Connections
- LTC 8901 Series CPU Relay Outputs and Buzzers
- LTC 8901 Series CPU Selection Switch
- Camera Phasing and Accessory Installation
- Satellite System Configuration Installations
- Allegiant Satellite System Configuration Installations
- Satellite Site “Trunk Line” Monitor Outputs
- Main Site “Trunk Line” Video Inputs
- Control Data Lines in Satellite Systems
- Satellite Sites Programming Requirements
- Main Site Programming Requirements
- Special Programming for “Cascaded” Satellite System Configurations
- Alarm Inputs in Satellite Systems
- Troubleshooting Guide
- Maintenance Information
- Pinouts
- Back Page
LTC 8808/00 Video Interconnect Panel
This patch panel contains 32 BNC connectors on its front for external video connections and
two 16-contact ribbon connectors on its rear. Two LTC 8809/00 16-conductor ribbon cables
are included for interfacing the patch panel to the video input or video output connectors on
the LTC 8902 Series Output Bays and LTC 8903 Series Input Bays.
LAN Cables
Three types of LAN cables are supplied with the system. The first type has a length of 8 m (25
ft). The second type is 3 m (10 ft) long. The third type is 2 m (6 ft) long and contain reversed
data connections. These shorter LAN cables are used exclusively for crossover connections
between the LTC 8944/93, LTC 8945/93, and LTC 8946/93 LAN switches.
Security Key for PC-based Software
The Master Control Software for Windows (MCSW) or the Graphical User Interface (GUI) PC-
based software programs can only be accessed when a Security Key is attached to the PC.
This key is used to prevent unauthorized access to the system software, and it should be kept
in a safe place if the need to remove it from the PC occurs. In redundant design system
configurations, a Security Key is supplied along with the preloaded MCSW software for use on
the LTC 8943/95 PC. In standard system configurations, the MCSW and its Key are included
for use on a user-supplied PC.
Miscellaneous Components
The system is supplied with other miscellaneous components including power cords for both
110V and 220 V outlets. The unused cords can be discarded. Figure 31 illustrates some of
these components along with other cables noted elsewhere in this manual.
4.11
4.12
4.13
4.14
20 en | System Components LTC 8900 Series
2016.04 | 10.7 | F.01U.323.096 Installation Manual Bosch Security Systems, Inc.