Installation Manual
Table Of Contents
- Title Page
- Table of Contents
- Safety
- Unpacking
- Introduction
- System Components
- LTC 8904 Series CPU Bay
- LTC 8901 Series CPU Bay
- LTC 8902 Series Output Bay
- LTC 8903 Series Input Bay
- LTC 8934/00 Video Output Modules
- LTC 8921/00 Video Input Modules
- LTC 8943/95 System Controller PC
- LTC 8944/93 and LTC 8945/93 LAN Switches
- LTC 8946/93 LAN Switches
- LTC 8809/00 Video Ribbon Cable
- LTC 8808/00 Video Interconnect Panel
- LAN Cables
- Security Key for PC-based Software
- Miscellaneous Components
- Hardware Installation Procedure for Standard Systems Utilizing LTC 8904 Series CPU
- General Installation Considerations
- LTC 8904 Series CPU Bay Installation
- LAN Switch Installation
- LTC 8902 Series Output Bay and LTC 8903 Series Input Bay Installation
- Module Insertion
- Data Receiver Modules
- LTC 8916/01 Data Receiver Modules
- LTC 8918/01 Data Receiver Modules
- LTC 8934/00 Video Output Modules
- LTC 8921/00 Video Input Modules
- System Video Connections
- Termination Practices
- System Data Connections
- Main Power Connections
- Hardware Installation Procedure for Redundant System Configuration Utilizing LTC 8901 Series CPU
- System Redundancy Considerations
- Main CPU Bay Installation
- LAN Switch Installation
- LTC 8943/95 System Controller PC Installation
- LTC 8902 Series Output Bay and LTC 8903 Series Input Bay Installation
- Module Insertion
- Data Receiver Modules
- LTC 8916/01 Data Receiver Modules
- LTC 8918/01 Data Receiver Modules
- LTC 8934/00 Video Output Modules
- LTC 8921/00 Video Input Modules
- System Video Connections
- Termination Practices
- System Data Connections
- Main Power Connections
- LTC 8901 Series CPU Relay Outputs and Buzzers
- LTC 8901 Series CPU Selection Switch
- Camera Phasing and Accessory Installation
- Satellite System Configuration Installations
- Allegiant Satellite System Configuration Installations
- Satellite Site “Trunk Line” Monitor Outputs
- Main Site “Trunk Line” Video Inputs
- Control Data Lines in Satellite Systems
- Satellite Sites Programming Requirements
- Main Site Programming Requirements
- Special Programming for “Cascaded” Satellite System Configurations
- Alarm Inputs in Satellite Systems
- Troubleshooting Guide
- Maintenance Information
- Pinouts
- Back Page
LTC 8902
Monitor Bay
LTC 8946 LAN Switch LTC 8904 CPU Bay
LTC 8902
Monitor Bay
LTC 8903
Camera Bay
LTC 8903
Camera Bay
LTC 8903
Camera Bay
LTC 8903
Camera Bay
LTC 8903
Camera Bay
LTC 8903
Camera Bay
LTC 8903
Camera Bay
LTC 8903
Camera Bay
Figure 5.1: LTC 8900 1024 Camera by 128 Monitor System Installed in Two 72 in. EIA Mounting Racks
LTC 8904 Series CPU Bay Installation
The LTC 8904 Series Main CPU Bay is supplied fully assembled and requires no user
adjustments. Install the CPU bay into the mounting rack.
NOTE: Rack-mounting screws and associated hardware are NOT included.
A L LE G IA N T M a trix C P U
Po we r
C PU A C T IV IT Y
BOSCH
Figure 5.2: LTC 8904 Series CPU Bay
It is recommended that the CPU bay be mounted so that a 9 cm (3-1/2 in.) rack space is
available either above or below the enclosure. In sites where the system can not be taken
out of operation for a period of time, this will leave a mounting space available for a
replacement CPU in the unlikely event that the original CPU must be removed for servicing.
Do not attach line cord to AC power source until instructed to do so.
5.2
22
en | Hardware Installation Procedure for Standard Systems Utilizing LTC 8904 Series
CPU
LTC 8900 Series
2016.04 | 10.7 | F.01U.323.096 Installation Manual Bosch Security Systems, Inc.