Installation Manual
Table Of Contents
- Title Page
- Table of Contents
- Safety
- Unpacking
- Introduction
- System Components
- LTC 8904 Series CPU Bay
- LTC 8901 Series CPU Bay
- LTC 8902 Series Output Bay
- LTC 8903 Series Input Bay
- LTC 8934/00 Video Output Modules
- LTC 8921/00 Video Input Modules
- LTC 8943/95 System Controller PC
- LTC 8944/93 and LTC 8945/93 LAN Switches
- LTC 8946/93 LAN Switches
- LTC 8809/00 Video Ribbon Cable
- LTC 8808/00 Video Interconnect Panel
- LAN Cables
- Security Key for PC-based Software
- Miscellaneous Components
- Hardware Installation Procedure for Standard Systems Utilizing LTC 8904 Series CPU
- General Installation Considerations
- LTC 8904 Series CPU Bay Installation
- LAN Switch Installation
- LTC 8902 Series Output Bay and LTC 8903 Series Input Bay Installation
- Module Insertion
- Data Receiver Modules
- LTC 8916/01 Data Receiver Modules
- LTC 8918/01 Data Receiver Modules
- LTC 8934/00 Video Output Modules
- LTC 8921/00 Video Input Modules
- System Video Connections
- Termination Practices
- System Data Connections
- Main Power Connections
- Hardware Installation Procedure for Redundant System Configuration Utilizing LTC 8901 Series CPU
- System Redundancy Considerations
- Main CPU Bay Installation
- LAN Switch Installation
- LTC 8943/95 System Controller PC Installation
- LTC 8902 Series Output Bay and LTC 8903 Series Input Bay Installation
- Module Insertion
- Data Receiver Modules
- LTC 8916/01 Data Receiver Modules
- LTC 8918/01 Data Receiver Modules
- LTC 8934/00 Video Output Modules
- LTC 8921/00 Video Input Modules
- System Video Connections
- Termination Practices
- System Data Connections
- Main Power Connections
- LTC 8901 Series CPU Relay Outputs and Buzzers
- LTC 8901 Series CPU Selection Switch
- Camera Phasing and Accessory Installation
- Satellite System Configuration Installations
- Allegiant Satellite System Configuration Installations
- Satellite Site “Trunk Line” Monitor Outputs
- Main Site “Trunk Line” Video Inputs
- Control Data Lines in Satellite Systems
- Satellite Sites Programming Requirements
- Main Site Programming Requirements
- Special Programming for “Cascaded” Satellite System Configurations
- Alarm Inputs in Satellite Systems
- Troubleshooting Guide
- Maintenance Information
- Pinouts
- Back Page
5. Install the LTC 8902 Series and LTC 8903 Series matrix bays close enough to the system
LAN switches (LTC 8944/93, LTC 8945/93, and LTC 8946/93) so that the supplied 8 m
(25 ft) LAN cables can be used.
If necessary due to unusual installation conditions, longer standard 10/100Base-T LAN
cables should be obtained from a local computer hardware supplier.
6. Once installed, exercise care to avoid damaging to the connectors on the matrix bays to
which the LTC 8809/00 ribbon cables are attached. The ribbon cable connectors contain
locking hooks that can be damaged if too much strain is put on the ribbon cables.
If necessary, support the LTC 8809/00 cables to eliminate excessive loading force on the
locking hooks.
7. Do not mix the different types of supplied LAN cables. The 3 m (10 ft) length is used
between the CPU and LAN switches. The 8 m (25 ft) length is used between the CPU and
the video matrix bays in all system configurations. The 2 m (6 ft) length has reversed data
connections and can only be used between the LTC 8944/93, LTC 8945/93, and LTC
8946/93 LAN switches.
H
LTC 8902
Monitor Bay
LTC 8902
Monitor Bay
LTC 8944 LAN Switch
LTC 8945 LAN Switch
LTC 8903
Camera Bay
LTC 8903
Camera Bay
LTC 8903
Camera Bay
LTC 8903
Camera Bay
LTC 8943
PC Station
LTC 8901 CPU Bay
Figure 6.5: LTC 8900 512 Cameras by 128 Monitors Redundant System Configuration Installed in two (2)
72-in. EIA mounting racks
Main CPU Bay Installation
The LTC 8900 Series Main CPU Bay is supplied fully assembled and requires no user
adjustments. Install CPU bay into the mounting rack. Note, rack-mounting screws and
associated hardware are NOT included.
6.2
LTC 8900 Series
Hardware Installation Procedure for Redundant System Configuration Utilizing LTC 8901
Series CPU | en
39
Bosch Security Systems, Inc. Installation Manual 2016.04 | 10.7 | F.01U.323.096