Installation Manual
Table Of Contents
- Title Page
- Table of Contents
- Safety
- Unpacking
- Introduction
- System Components
- LTC 8904 Series CPU Bay
- LTC 8901 Series CPU Bay
- LTC 8902 Series Output Bay
- LTC 8903 Series Input Bay
- LTC 8934/00 Video Output Modules
- LTC 8921/00 Video Input Modules
- LTC 8943/95 System Controller PC
- LTC 8944/93 and LTC 8945/93 LAN Switches
- LTC 8946/93 LAN Switches
- LTC 8809/00 Video Ribbon Cable
- LTC 8808/00 Video Interconnect Panel
- LAN Cables
- Security Key for PC-based Software
- Miscellaneous Components
- Hardware Installation Procedure for Standard Systems Utilizing LTC 8904 Series CPU
- General Installation Considerations
- LTC 8904 Series CPU Bay Installation
- LAN Switch Installation
- LTC 8902 Series Output Bay and LTC 8903 Series Input Bay Installation
- Module Insertion
- Data Receiver Modules
- LTC 8916/01 Data Receiver Modules
- LTC 8918/01 Data Receiver Modules
- LTC 8934/00 Video Output Modules
- LTC 8921/00 Video Input Modules
- System Video Connections
- Termination Practices
- System Data Connections
- Main Power Connections
- Hardware Installation Procedure for Redundant System Configuration Utilizing LTC 8901 Series CPU
- System Redundancy Considerations
- Main CPU Bay Installation
- LAN Switch Installation
- LTC 8943/95 System Controller PC Installation
- LTC 8902 Series Output Bay and LTC 8903 Series Input Bay Installation
- Module Insertion
- Data Receiver Modules
- LTC 8916/01 Data Receiver Modules
- LTC 8918/01 Data Receiver Modules
- LTC 8934/00 Video Output Modules
- LTC 8921/00 Video Input Modules
- System Video Connections
- Termination Practices
- System Data Connections
- Main Power Connections
- LTC 8901 Series CPU Relay Outputs and Buzzers
- LTC 8901 Series CPU Selection Switch
- Camera Phasing and Accessory Installation
- Satellite System Configuration Installations
- Allegiant Satellite System Configuration Installations
- Satellite Site “Trunk Line” Monitor Outputs
- Main Site “Trunk Line” Video Inputs
- Control Data Lines in Satellite Systems
- Satellite Sites Programming Requirements
- Main Site Programming Requirements
- Special Programming for “Cascaded” Satellite System Configurations
- Alarm Inputs in Satellite Systems
- Troubleshooting Guide
- Maintenance Information
- Pinouts
- Back Page
6.14.5 LTC 8943/95 PC to LTC 8945/93 LAN Switch Connectors 50
6.15 Main Power Connections 50
6.16 LTC 8901 Series CPU Relay Outputs and Buzzers 52
6.17 LTC 8901 Series CPU Selection Switch 53
7
Camera Phasing and Accessory Installation 54
7.1 Camera Phasing Information 54
7.2 External Sync Information 54
7.3 System Keyboard Installation 54
7.4 Signal Distribution Unit Hookup 55
7.5 Alarm Interface Unit Hookup 55
7.6 External Computer Interface Connections 55
7.7 Logging Printer Option Installation 55
8
Satellite System Configuration Installations 57
8.1 Allegiant Satellite System Configuration Installations 58
8.2 Satellite Site “Trunk Line” Monitor Outputs 64
8.3 Main Site “Trunk Line” Video Inputs 64
8.4 Control Data Lines in Satellite Systems 64
8.5 Satellite Sites Programming Requirements 64
8.6 Main Site Programming Requirements 65
8.7 Special Programming for “Cascaded” Satellite System Configurations 67
8.8 Alarm Inputs in Satellite Systems 68
9
Troubleshooting Guide 100
10
Maintenance Information 103
10.1 Cleaning System Keyboard(s) 103
10.2 Matrix Bay AC Line Voltage Input Selection 103
10.3 Matrix Bay AC Line Fuse Replacement 104
10.4 Matrix Bay Power Supply Fuse Replacement 105
10.5 Replacing LTC 8901 or LTC 8904 Series CPU Parts 105
10.6 LTC 8943/95 System Controller PC 106
10.7 Replacement of Memory Backup Batteries 106
11
Pinouts 108
LTC 8900 Series Table of Contents | en 5
Bosch Security Systems, Inc. Installation Manual 2016.04 | 10.7 | F.01U.323.096