Installation Manual
Table Of Contents
- Title Page
- Table of Contents
- Safety
- Unpacking
- Introduction
- System Components
- LTC 8904 Series CPU Bay
- LTC 8901 Series CPU Bay
- LTC 8902 Series Output Bay
- LTC 8903 Series Input Bay
- LTC 8934/00 Video Output Modules
- LTC 8921/00 Video Input Modules
- LTC 8943/95 System Controller PC
- LTC 8944/93 and LTC 8945/93 LAN Switches
- LTC 8946/93 LAN Switches
- LTC 8809/00 Video Ribbon Cable
- LTC 8808/00 Video Interconnect Panel
- LAN Cables
- Security Key for PC-based Software
- Miscellaneous Components
- Hardware Installation Procedure for Standard Systems Utilizing LTC 8904 Series CPU
- General Installation Considerations
- LTC 8904 Series CPU Bay Installation
- LAN Switch Installation
- LTC 8902 Series Output Bay and LTC 8903 Series Input Bay Installation
- Module Insertion
- Data Receiver Modules
- LTC 8916/01 Data Receiver Modules
- LTC 8918/01 Data Receiver Modules
- LTC 8934/00 Video Output Modules
- LTC 8921/00 Video Input Modules
- System Video Connections
- Termination Practices
- System Data Connections
- Main Power Connections
- Hardware Installation Procedure for Redundant System Configuration Utilizing LTC 8901 Series CPU
- System Redundancy Considerations
- Main CPU Bay Installation
- LAN Switch Installation
- LTC 8943/95 System Controller PC Installation
- LTC 8902 Series Output Bay and LTC 8903 Series Input Bay Installation
- Module Insertion
- Data Receiver Modules
- LTC 8916/01 Data Receiver Modules
- LTC 8918/01 Data Receiver Modules
- LTC 8934/00 Video Output Modules
- LTC 8921/00 Video Input Modules
- System Video Connections
- Termination Practices
- System Data Connections
- Main Power Connections
- LTC 8901 Series CPU Relay Outputs and Buzzers
- LTC 8901 Series CPU Selection Switch
- Camera Phasing and Accessory Installation
- Satellite System Configuration Installations
- Allegiant Satellite System Configuration Installations
- Satellite Site “Trunk Line” Monitor Outputs
- Main Site “Trunk Line” Video Inputs
- Control Data Lines in Satellite Systems
- Satellite Sites Programming Requirements
- Main Site Programming Requirements
- Special Programming for “Cascaded” Satellite System Configurations
- Alarm Inputs in Satellite Systems
- Troubleshooting Guide
- Maintenance Information
- Pinouts
- Back Page
Satellite System Configuration Installations
A satellite system configuration is usually used for a medium to large distributed system, or to
obtain extremely large matrix sizes configured more conventionally. Typically, a single Main
control site can be used to view/control cameras located both locally and at various remote
satellite sites. Since up to 256 satellite sites can be linked to a single Main control site, very
large, distributed systems can be achieved. If the satellite systems are located at the same site
as the Main system, the result is a large conventional-type system.
In a satellite configuration, the Main control site can view/control any camera in the entire
system, but the remote satellite sites can only view/control cameras associated with their own
site. Satellites may be configured to operate either independently or with no local viewing/
control capability.
It is also possible to configure satellite systems where each site can view/control cameras
from anywhere in the system. For a 2 site system, this is referred to as a dual master
configuration. In the same manner, triple and quadruple master system configurations can also
be configured. Cascaded satellite systems, where a Main site has a satellite which is a master
to another satellite, is another available scenario. In fact, it is possible to configure systems
that include a mixture of any or all of the above scenarios.
C entral
C ontrol
S tation
Satellite
System #6
Satellite
System #5
Satellite
System #4
Satellite
System #3
Satellite
System #1
Satellite
System #2
Data
Data
Data
Dat
a
Data
Data
Video
Video
Video
Vdeo
Video
Video
The central station can view/control cameras located
at any site. The satellite sites can view/control
cameras located only within their own site.
Figure 8.1: Satellite Concept Configuration
Refer to the LTC 8850/00 GUI Software manual or the LTC 8059/00 MCS package manual for
additional configuration and programming information on satellite systems.
8
LTC 8900 Series Satellite System Configuration Installations | en 57
Bosch Security Systems, Inc. Installation Manual 2016.04 | 10.7 | F.01U.323.096