Installation Manual
Table Of Contents
- Title Page
- Table of Contents
- Safety
- Unpacking
- Introduction
- System Components
- LTC 8904 Series CPU Bay
- LTC 8901 Series CPU Bay
- LTC 8902 Series Output Bay
- LTC 8903 Series Input Bay
- LTC 8934/00 Video Output Modules
- LTC 8921/00 Video Input Modules
- LTC 8943/95 System Controller PC
- LTC 8944/93 and LTC 8945/93 LAN Switches
- LTC 8946/93 LAN Switches
- LTC 8809/00 Video Ribbon Cable
- LTC 8808/00 Video Interconnect Panel
- LAN Cables
- Security Key for PC-based Software
- Miscellaneous Components
- Hardware Installation Procedure for Standard Systems Utilizing LTC 8904 Series CPU
- General Installation Considerations
- LTC 8904 Series CPU Bay Installation
- LAN Switch Installation
- LTC 8902 Series Output Bay and LTC 8903 Series Input Bay Installation
- Module Insertion
- Data Receiver Modules
- LTC 8916/01 Data Receiver Modules
- LTC 8918/01 Data Receiver Modules
- LTC 8934/00 Video Output Modules
- LTC 8921/00 Video Input Modules
- System Video Connections
- Termination Practices
- System Data Connections
- Main Power Connections
- Hardware Installation Procedure for Redundant System Configuration Utilizing LTC 8901 Series CPU
- System Redundancy Considerations
- Main CPU Bay Installation
- LAN Switch Installation
- LTC 8943/95 System Controller PC Installation
- LTC 8902 Series Output Bay and LTC 8903 Series Input Bay Installation
- Module Insertion
- Data Receiver Modules
- LTC 8916/01 Data Receiver Modules
- LTC 8918/01 Data Receiver Modules
- LTC 8934/00 Video Output Modules
- LTC 8921/00 Video Input Modules
- System Video Connections
- Termination Practices
- System Data Connections
- Main Power Connections
- LTC 8901 Series CPU Relay Outputs and Buzzers
- LTC 8901 Series CPU Selection Switch
- Camera Phasing and Accessory Installation
- Satellite System Configuration Installations
- Allegiant Satellite System Configuration Installations
- Satellite Site “Trunk Line” Monitor Outputs
- Main Site “Trunk Line” Video Inputs
- Control Data Lines in Satellite Systems
- Satellite Sites Programming Requirements
- Main Site Programming Requirements
- Special Programming for “Cascaded” Satellite System Configurations
- Alarm Inputs in Satellite Systems
- Troubleshooting Guide
- Maintenance Information
- Pinouts
- Back Page
Typical Biphase
Data lines to all local
P/T/Z cameras
Typical Allegiant ‘Primary’ Master Site 1
1 or More Video
TRUNK Lines
Biphase Data Line to
Intermediate Master/Satellite
Biphase
Data
Typical Allegiant ‘Intermediate’ Master/Satellite, Site 2
Biphase
Data
Allegiant
ALLEGIANT Video Matrix
Allegiant
ALLEGIANT Video Matrix
Signal Distribution Unit
Video
ALLEGIANT Data Unit
CODE
POWER
LTC 8568
Console
Port
Biphase
Data
Typical Allegiant Satellite, Site 3
Biphase
Data
Allegiant
ALLEGIANT Video Matrix
Typical Biphase Data
line to all local P/T/Z
cameras
Video
ALLEGIANT Data Unit
CODE
POWER
LTC 8569
RS-232 IN
CODE OUT
CODE IN
RS-232 OUT
LTC 8780
Console
Port
Biphase
Data
Typical Biphase Data line
to all local P/T/Z cameras
ALLEGIANT Data Unit
CODE
POWER
LTC 8569
RS-232 IN
CODE OUT
CODE IN
RS-232 OUT
Biphase Data Line
to 3
rd
Level Satellite
Multiple Video
TRUNK Lines
Code Merger unit
Data
Converter Unit
LTC 8780
Data
Converter Unit
Code
Merger unit
Typical PTZ Camera
Typical PTZ Camera
Typical PTZ Camera
Video
Typical System Monitors
(Video from all sites)
1
2
3
4
5
6
7 8 9
0
Sh
ot
Mo
n
Pro
d
Cl
r
BOSC
H
Typical IntuiKey keyboard
BOSCH BOSCH
Typical System Monitors
(Video from sites 2 and 3)
1 2 3
4 5 6
7 8 9
0
Sh
ot
Mo
n
Pro
d
Cl
r
BOSC
H
Typical IntuiKey keyboard
BOSCH BOSCH
Typical System Monitors
(Video from local site only)
1 2 3
4 5 6
7 8 9
0
Sh
ot
Mo
n
Pro
d
Cl
r
BOSC
H
Typical IntuiKey keyboard
BOSCH BOSCH
Figure 8.5: Conceptual Diagram of a Cascaded Allegiant Satellite System
LTC 8900 Series Satellite System Configuration Installations | en 63
Bosch Security Systems, Inc. Installation Manual 2016.04 | 10.7 | F.01U.323.096