Installation Manual
Table Of Contents
- Title Page
- Table of Contents
- Safety
- Unpacking
- Introduction
- System Components
- LTC 8904 Series CPU Bay
- LTC 8901 Series CPU Bay
- LTC 8902 Series Output Bay
- LTC 8903 Series Input Bay
- LTC 8934/00 Video Output Modules
- LTC 8921/00 Video Input Modules
- LTC 8943/95 System Controller PC
- LTC 8944/93 and LTC 8945/93 LAN Switches
- LTC 8946/93 LAN Switches
- LTC 8809/00 Video Ribbon Cable
- LTC 8808/00 Video Interconnect Panel
- LAN Cables
- Security Key for PC-based Software
- Miscellaneous Components
- Hardware Installation Procedure for Standard Systems Utilizing LTC 8904 Series CPU
- General Installation Considerations
- LTC 8904 Series CPU Bay Installation
- LAN Switch Installation
- LTC 8902 Series Output Bay and LTC 8903 Series Input Bay Installation
- Module Insertion
- Data Receiver Modules
- LTC 8916/01 Data Receiver Modules
- LTC 8918/01 Data Receiver Modules
- LTC 8934/00 Video Output Modules
- LTC 8921/00 Video Input Modules
- System Video Connections
- Termination Practices
- System Data Connections
- Main Power Connections
- Hardware Installation Procedure for Redundant System Configuration Utilizing LTC 8901 Series CPU
- System Redundancy Considerations
- Main CPU Bay Installation
- LAN Switch Installation
- LTC 8943/95 System Controller PC Installation
- LTC 8902 Series Output Bay and LTC 8903 Series Input Bay Installation
- Module Insertion
- Data Receiver Modules
- LTC 8916/01 Data Receiver Modules
- LTC 8918/01 Data Receiver Modules
- LTC 8934/00 Video Output Modules
- LTC 8921/00 Video Input Modules
- System Video Connections
- Termination Practices
- System Data Connections
- Main Power Connections
- LTC 8901 Series CPU Relay Outputs and Buzzers
- LTC 8901 Series CPU Selection Switch
- Camera Phasing and Accessory Installation
- Satellite System Configuration Installations
- Allegiant Satellite System Configuration Installations
- Satellite Site “Trunk Line” Monitor Outputs
- Main Site “Trunk Line” Video Inputs
- Control Data Lines in Satellite Systems
- Satellite Sites Programming Requirements
- Main Site Programming Requirements
- Special Programming for “Cascaded” Satellite System Configurations
- Alarm Inputs in Satellite Systems
- Troubleshooting Guide
- Maintenance Information
- Pinouts
- Back Page
1 4 5 8 9 12 13 16
1
to
16
17
to
32
33
to
48
49
to
64
65
to
80
81
to
96
97
to
112
113
to
128
129
to
144
145
to
160
161
to
176
177
to
192
193
to
208
209
to
224
225
to
240
241
to
256
<--
<--
Bus
Lines
Rear
Panel
Ribbon
Connectors
Video
input
Module
Slots
“Primary” Level
LTC 8903 Bay for
Cameras 1 to 256
“Primary” Level
LTC 8903 Bay for
Cameras 257 to 512
“Primary” Level
LTC 8903 Bay for
Cameras 513 to 768
“Primary” Level
LTC 8903 Bay for
Cameras 769 to 1024
Slot
not
used
Slot
not
used
Slot
not
used
Slot
not
used
Slot
not
used
Slot
not
used
Slot
not
used
Slot
not
used
Backplane Bus Backplane Bus
Eight LTC 8921 Video Input Modules are required in an LTC 8903 Bay with a 64 Monitor Bus
Four LTC 8921 Video Input Modules (in slot numbers 1, 5, 9, 13) are required in an LTC 8903 Bay with a 32 Monitor Bus
Internal Video Bus
Concept of “Secondary”
Level LTC 8903
or Cameras 1 to 1024
LTC 8809
Ribbon Cables
Camera Range
Monitor Bus
Video Bus to
LTC 8902 Bay
for Monitors 33 to 64
Video Bus to
LTC 8902 Bay
for Monitors 1 to 32
1-256
1-16
1-256
17-32
1-256
33-48
1-256
49-64
257-512
1-16
257-512
17-32
257-512
33-48
257-512
49-64
513-768
1-16
513-768
17-32
513-768
33-48
513-768
49-64
769-1024
1-16
769-1024
17-32
769-1024
33-48
769-1024
49-64
Figure 8.28: Video Bus Concept Diagram
84
en | Satellite System Configuration Installations LTC 8900 Series
2016.04 | 10.7 | F.01U.323.096 Installation Manual Bosch Security Systems, Inc.