Installation Manual
Table Of Contents
- Title Page
- Table of Contents
- Safety
- Unpacking
- Introduction
- System Components
- LTC 8904 Series CPU Bay
- LTC 8901 Series CPU Bay
- LTC 8902 Series Output Bay
- LTC 8903 Series Input Bay
- LTC 8934/00 Video Output Modules
- LTC 8921/00 Video Input Modules
- LTC 8943/95 System Controller PC
- LTC 8944/93 and LTC 8945/93 LAN Switches
- LTC 8946/93 LAN Switches
- LTC 8809/00 Video Ribbon Cable
- LTC 8808/00 Video Interconnect Panel
- LAN Cables
- Security Key for PC-based Software
- Miscellaneous Components
- Hardware Installation Procedure for Standard Systems Utilizing LTC 8904 Series CPU
- General Installation Considerations
- LTC 8904 Series CPU Bay Installation
- LAN Switch Installation
- LTC 8902 Series Output Bay and LTC 8903 Series Input Bay Installation
- Module Insertion
- Data Receiver Modules
- LTC 8916/01 Data Receiver Modules
- LTC 8918/01 Data Receiver Modules
- LTC 8934/00 Video Output Modules
- LTC 8921/00 Video Input Modules
- System Video Connections
- Termination Practices
- System Data Connections
- Main Power Connections
- Hardware Installation Procedure for Redundant System Configuration Utilizing LTC 8901 Series CPU
- System Redundancy Considerations
- Main CPU Bay Installation
- LAN Switch Installation
- LTC 8943/95 System Controller PC Installation
- LTC 8902 Series Output Bay and LTC 8903 Series Input Bay Installation
- Module Insertion
- Data Receiver Modules
- LTC 8916/01 Data Receiver Modules
- LTC 8918/01 Data Receiver Modules
- LTC 8934/00 Video Output Modules
- LTC 8921/00 Video Input Modules
- System Video Connections
- Termination Practices
- System Data Connections
- Main Power Connections
- LTC 8901 Series CPU Relay Outputs and Buzzers
- LTC 8901 Series CPU Selection Switch
- Camera Phasing and Accessory Installation
- Satellite System Configuration Installations
- Allegiant Satellite System Configuration Installations
- Satellite Site “Trunk Line” Monitor Outputs
- Main Site “Trunk Line” Video Inputs
- Control Data Lines in Satellite Systems
- Satellite Sites Programming Requirements
- Main Site Programming Requirements
- Special Programming for “Cascaded” Satellite System Configurations
- Alarm Inputs in Satellite Systems
- Troubleshooting Guide
- Maintenance Information
- Pinouts
- Back Page
"A "
1234123412341234
"B ""C "
"D "
"A "
1234123412341234
"B ""C "
"D "
4 LTC 8934 Video Output Modules
Installed in the first 4 Slots are Required for
Monitors 1 to 32. Set all Termination
Switches to ON Position on all Modules.
All Termination Switches are set to ON
Position on all LTC 8921 Video Input Modules
Front view – Module Placement and Te rmination Settings
8 LTC 8921 Video Input Modules are
Installed in odd Numbered Slots only
are Required for Camera Inputs 1 to 256
8 LTC 8934 Video Output Modules are
Required for Monitors 1 to 64.
Set all Termination Switches to ON
Position on all Modules.
Set LTC 8921 Module Termination
switches in ODD Numbered Slots to OFF
Set LTC 8921 Module Termination
Switches in EVEN Numbered Slots to ON
Front view – Module Placement and Te rmination Settings
16 LTC 8921 Video Input Modules
Required for Camera Inputs 1 to 256
Module, Termination, and Interconnect Cabling for 256 Camera by 32 Monitor System
Module, Termination, and Interconnect Cabling for 256 Camera by 64 Monitor System
Monitors 1-32
Monitors 33-64
Monitors 1-32
Lower
LTC 8809
Ribbon Cable
Lower LTC 8809
Ribbon Cable
Lower LTC 8809
Ribbon Cable
Upper LTC 8809
Ribbon Cable
Upper LTC 8809
Ribbon Cable
Upper LTC 8809
Ribbon Cable
Lower
LTC 8809
Ribbon Cable
Upper LTC 8809
Ribbon Cable
2 LTC 8809 Cables
Required for 32-Channel
Video Bus to the LTC 8902
4 LTC 8809 Cables
Required for 64-Channel
Video Bus to the LTC 8902
Rear view – LTC 8809 Interconnect Cable Routing
LTC 8902
LTC 8902
8 LTC 8808 Panels are Required
for Camera Inputs 1 to 256
8 LTC 8808 Panels are Required
for Camera Inputs 1 to 256
To Video
in “B”
To Video
in “B”
To video in “A”
To Video in “A”
To
“A1”
To
“A1”
To
“D1”
To “C1”
To “B1”
To “B1”
LTC 8903
LTC 8903
Rear view – LTC 8809 Interconnect Cable Routing
LTC 8903
LTC 8903
LTC 8902
LTC 8902
Figure 8.29: Module, Termination, and Interconnect Cabling for 256 Cameras by 32 or 64 Monitor Systems
LTC 8900 Series
Satellite System Configuration Installations | en 85
Bosch Security Systems, Inc. Installation Manual 2016.04 | 10.7 | F.01U.323.096