Installation Manual
Table Of Contents
- Title Page
- Table of Contents
- Safety
- Unpacking
- Introduction
- System Components
- LTC 8904 Series CPU Bay
- LTC 8901 Series CPU Bay
- LTC 8902 Series Output Bay
- LTC 8903 Series Input Bay
- LTC 8934/00 Video Output Modules
- LTC 8921/00 Video Input Modules
- LTC 8943/95 System Controller PC
- LTC 8944/93 and LTC 8945/93 LAN Switches
- LTC 8946/93 LAN Switches
- LTC 8809/00 Video Ribbon Cable
- LTC 8808/00 Video Interconnect Panel
- LAN Cables
- Security Key for PC-based Software
- Miscellaneous Components
- Hardware Installation Procedure for Standard Systems Utilizing LTC 8904 Series CPU
- General Installation Considerations
- LTC 8904 Series CPU Bay Installation
- LAN Switch Installation
- LTC 8902 Series Output Bay and LTC 8903 Series Input Bay Installation
- Module Insertion
- Data Receiver Modules
- LTC 8916/01 Data Receiver Modules
- LTC 8918/01 Data Receiver Modules
- LTC 8934/00 Video Output Modules
- LTC 8921/00 Video Input Modules
- System Video Connections
- Termination Practices
- System Data Connections
- Main Power Connections
- Hardware Installation Procedure for Redundant System Configuration Utilizing LTC 8901 Series CPU
- System Redundancy Considerations
- Main CPU Bay Installation
- LAN Switch Installation
- LTC 8943/95 System Controller PC Installation
- LTC 8902 Series Output Bay and LTC 8903 Series Input Bay Installation
- Module Insertion
- Data Receiver Modules
- LTC 8916/01 Data Receiver Modules
- LTC 8918/01 Data Receiver Modules
- LTC 8934/00 Video Output Modules
- LTC 8921/00 Video Input Modules
- System Video Connections
- Termination Practices
- System Data Connections
- Main Power Connections
- LTC 8901 Series CPU Relay Outputs and Buzzers
- LTC 8901 Series CPU Selection Switch
- Camera Phasing and Accessory Installation
- Satellite System Configuration Installations
- Allegiant Satellite System Configuration Installations
- Satellite Site “Trunk Line” Monitor Outputs
- Main Site “Trunk Line” Video Inputs
- Control Data Lines in Satellite Systems
- Satellite Sites Programming Requirements
- Main Site Programming Requirements
- Special Programming for “Cascaded” Satellite System Configurations
- Alarm Inputs in Satellite Systems
- Troubleshooting Guide
- Maintenance Information
- Pinouts
- Back Page
16 LTC 8921 Video Input
Modules are Required for
Camera Inputs 1025 to 1280
16 LTC 8921 Video Input
Modules are Required for
Camera Inputs 1281 to 1536
16 LTC 8921 Video Input
Modules are Required for
Camera Inputs 1537 to 1792
16 LTC 8921 Video Input
Modules are Required for
Camera Inputs 1793 to 2048
“Primary” LTC 8903 Bay
Cameras 257–512
“Primary” LTC 8903 Bay
Cameras 1–256
“Primary” LTC 8903 Bay
Cameras 513–768
“Primary” LTC 8903 Bay
Cameras 769–1024
“Primary” LTC 8903 Bay
Cameras 1537–1792
“Primary” LTC 8903 Bay
Cameras 1793–2048
“Primary” LTC 8903 Bay
Cameras 1281–1536
“Primary” LTC 8903 Bay
Cameras 1025–1280
LTC 8902
8 LTC 8934 Video Output Modules
are Required for Monitors 1 to 64.
Set all Termination Switches to
ON for all Modules.
Set the LTC 8921 Module Termination
Switches in ODD Numbered Slots
to OFF (all Primary LTC 8902 Bays)
Set the LTC 8921 Module Termination
Switches in EVEN Numbered Slots to
ON (all Primary LTC 8903 Bays)
“Secondary” Level LTC 8903 Bay
(for Camera Range 1 to 1024)
“Secondary” Level LTC 8903 Bay
(for Camera Range 1025 to 2048)
Front View – Module Placement and Termination Settings
8 LTC 8921 Video Input Modules
(in Slots 1, 4, 5, 8, 9, 12, 13, and 16)
are Required for 64 Monitor Systems
Set all Termination Switches on
LTC 8921 Modules in the “Secondary”
LTC 8921 Bay to ON
8 LTC 8921 Video Input Modules
(in Slots 1, 4, 5, 8, 9, 12, 13, and 16)
are Required for 64 Monitor Systems
Set all Termination Switches on
LTC 8921 Modules in the “Secondary”
LTC 8921 Bay to ON
16 LTC 8921 Video Input
Modules are Required for
Camera Inputs 1 to 256
16 LTC 8921 Video Input
Modules are Required for
Camera Inputs 257 to 512
16 LTC 8921 Video Input
Modules are Required for
Camera Inputs 513 to 768
16 LTC 8921 Video Input
Modules are Required for
Camera Inputs 769 to 1024
Figure 8.35: Module, Replacement, and Termination Configuration for 2048 Camera by 64 Monitor System
LTC 8900 Series Satellite System Configuration Installations | en 91
Bosch Security Systems, Inc. Installation Manual 2016.04 | 10.7 | F.01U.323.096