Installation Manual
Table Of Contents
- Title Page
- Table of Contents
- Safety
- Unpacking
- Introduction
- System Components
- LTC 8904 Series CPU Bay
- LTC 8901 Series CPU Bay
- LTC 8902 Series Output Bay
- LTC 8903 Series Input Bay
- LTC 8934/00 Video Output Modules
- LTC 8921/00 Video Input Modules
- LTC 8943/95 System Controller PC
- LTC 8944/93 and LTC 8945/93 LAN Switches
- LTC 8946/93 LAN Switches
- LTC 8809/00 Video Ribbon Cable
- LTC 8808/00 Video Interconnect Panel
- LAN Cables
- Security Key for PC-based Software
- Miscellaneous Components
- Hardware Installation Procedure for Standard Systems Utilizing LTC 8904 Series CPU
- General Installation Considerations
- LTC 8904 Series CPU Bay Installation
- LAN Switch Installation
- LTC 8902 Series Output Bay and LTC 8903 Series Input Bay Installation
- Module Insertion
- Data Receiver Modules
- LTC 8916/01 Data Receiver Modules
- LTC 8918/01 Data Receiver Modules
- LTC 8934/00 Video Output Modules
- LTC 8921/00 Video Input Modules
- System Video Connections
- Termination Practices
- System Data Connections
- Main Power Connections
- Hardware Installation Procedure for Redundant System Configuration Utilizing LTC 8901 Series CPU
- System Redundancy Considerations
- Main CPU Bay Installation
- LAN Switch Installation
- LTC 8943/95 System Controller PC Installation
- LTC 8902 Series Output Bay and LTC 8903 Series Input Bay Installation
- Module Insertion
- Data Receiver Modules
- LTC 8916/01 Data Receiver Modules
- LTC 8918/01 Data Receiver Modules
- LTC 8934/00 Video Output Modules
- LTC 8921/00 Video Input Modules
- System Video Connections
- Termination Practices
- System Data Connections
- Main Power Connections
- LTC 8901 Series CPU Relay Outputs and Buzzers
- LTC 8901 Series CPU Selection Switch
- Camera Phasing and Accessory Installation
- Satellite System Configuration Installations
- Allegiant Satellite System Configuration Installations
- Satellite Site “Trunk Line” Monitor Outputs
- Main Site “Trunk Line” Video Inputs
- Control Data Lines in Satellite Systems
- Satellite Sites Programming Requirements
- Main Site Programming Requirements
- Special Programming for “Cascaded” Satellite System Configurations
- Alarm Inputs in Satellite Systems
- Troubleshooting Guide
- Maintenance Information
- Pinouts
- Back Page
"A "
123
4
1
23
4123412
34
"B "
"C "
"D "
"A "
123
4
1
23
4123412
34
"B "
"C "
"D "
Lower
LTC 8809
Ribbon
Cable
Upper
LTC 8809
Ribbon
Cable
Monitors 33–64
Monitors 1–32
Lower
LTC 8809
Ribbon
Cable
Upper
LTC 8809
Ribbon
Cable
Monitors 65–96
Each Line Represents an
LTC 8809 Ribbon Cable
Each Line Represents an
LTC 8809 Ribbon Cable
Second Level LTC 8902
Monitors 65 to 96
First Level LTC 8902
Monitors 1 to 64
LTC 8903
Up to 16 LTC 8809
Ribbon Cables
LTC 8809 Cable for
Cameras 241 to 256
LTC 8809 Cable for
Cameras 1 to 16
LTC 8903
8 LTC 8808 Panels are Required
for Camera Inputs 1 to 256
For 256 cameras,
16 LTC 8809 Ribbon
Cables are Required to Jump
from First Level “Loop”
Outputs to Second Level
“Video In” Inputs
To Video
In “A”
To Video
In “B”
To “A1”
To “A1”
To “D1”
“B1”
“B1”
“C1”
Rear View – LTC 8809 Interconnect Cable Routing
Front View – Module Placement and Termination Settings
LTC 8902 for Monitors 1 to 64
Only 8 LTC 8921 Video Input Modules
are Required in this Level for 256
Cameras because the LTC 8902 Output
Bay Supports only 32 Monitors
4 LTC 8934 Video Output Modules
are Required for Monitors 65 to 96. Set all Termination
Switches to ON for all Modules.
Set all LTC 8921 Module
Termination Switches Inside
First Level LTC 8903 Bays to OFF
LTC 8902 for Monitors 65 to 96
Second Level LTC 8903
Cameras 1 - 256
First Level LTC 8903
Cameras 1 - 256
Video Interconnect LTC 8809 Cables
Video Interconnect LTC 8809 Cables
LTC 8809
Video
Looping
Connections
System Cameras Connect to the First
Level LTC 8903 Video Input Bay
8 LTC 8934 Video Output Modules
are Required for Monitors 1 to 64. Set all Termination
Switches to ON for all Modules.
16 LTC 8921 Video Input Modules
are Required for Cameras 1 to 256
Install LTC 8921 Modules in ODD Numbered
Slots only. Set all Termination Switches to ON.
Figure 8.37: Module, Termination, and Interconnect Cabling for 256 Camera by 96 Monitor System
LTC 8900 Series Satellite System Configuration Installations | en 93
Bosch Security Systems, Inc. Installation Manual 2016.04 | 10.7 | F.01U.323.096