Installation Manual
Table Of Contents
- Title Page
- Table of Contents
- Safety
- Unpacking
- Introduction
- System Components
- LTC 8904 Series CPU Bay
- LTC 8901 Series CPU Bay
- LTC 8902 Series Output Bay
- LTC 8903 Series Input Bay
- LTC 8934/00 Video Output Modules
- LTC 8921/00 Video Input Modules
- LTC 8943/95 System Controller PC
- LTC 8944/93 and LTC 8945/93 LAN Switches
- LTC 8946/93 LAN Switches
- LTC 8809/00 Video Ribbon Cable
- LTC 8808/00 Video Interconnect Panel
- LAN Cables
- Security Key for PC-based Software
- Miscellaneous Components
- Hardware Installation Procedure for Standard Systems Utilizing LTC 8904 Series CPU
- General Installation Considerations
- LTC 8904 Series CPU Bay Installation
- LAN Switch Installation
- LTC 8902 Series Output Bay and LTC 8903 Series Input Bay Installation
- Module Insertion
- Data Receiver Modules
- LTC 8916/01 Data Receiver Modules
- LTC 8918/01 Data Receiver Modules
- LTC 8934/00 Video Output Modules
- LTC 8921/00 Video Input Modules
- System Video Connections
- Termination Practices
- System Data Connections
- Main Power Connections
- Hardware Installation Procedure for Redundant System Configuration Utilizing LTC 8901 Series CPU
- System Redundancy Considerations
- Main CPU Bay Installation
- LAN Switch Installation
- LTC 8943/95 System Controller PC Installation
- LTC 8902 Series Output Bay and LTC 8903 Series Input Bay Installation
- Module Insertion
- Data Receiver Modules
- LTC 8916/01 Data Receiver Modules
- LTC 8918/01 Data Receiver Modules
- LTC 8934/00 Video Output Modules
- LTC 8921/00 Video Input Modules
- System Video Connections
- Termination Practices
- System Data Connections
- Main Power Connections
- LTC 8901 Series CPU Relay Outputs and Buzzers
- LTC 8901 Series CPU Selection Switch
- Camera Phasing and Accessory Installation
- Satellite System Configuration Installations
- Allegiant Satellite System Configuration Installations
- Satellite Site “Trunk Line” Monitor Outputs
- Main Site “Trunk Line” Video Inputs
- Control Data Lines in Satellite Systems
- Satellite Sites Programming Requirements
- Main Site Programming Requirements
- Special Programming for “Cascaded” Satellite System Configurations
- Alarm Inputs in Satellite Systems
- Troubleshooting Guide
- Maintenance Information
- Pinouts
- Back Page
System Cameras Connect
to First Level LTC 8903
Video Input Bay
16 LTC 8921 Video Input
Modules are Required for
Cameras 1 to 256
System Cameras Connect
to First Level LTC 8903
Video Input Bay
16 LTC 8921 Video Input
Modules are Required for
Cameras 257 to 512
System Cameras Connect
to First Level LTC 8903
Video Input Bay
16 LTC 8921 Video Input
Modules are Required for
Cameras 513 to 768
System Cameras Connect
to First Level LTC 8903
Video Input Bay
16 LTC 8921 Video Input
Modules are Required for
Cameras 769 to 1024
First Level LTC 8903
Cameras 1–256
First Level LTC 8903
Cameras 257–512
Second Level LTC 8903
Cameras 1–256
Second Level LTC 8903
Cameras 257–512
First Level LTC 8903
Cameras 513–768
First Level LTC 8903
Cameras 769–1024
Second Level LTC 8903
Cameras 513–768
Second Level LTC 8903
Cameras 769–1024
Video Looping
Connections
Video Looping ConnectionsVideo Looping ConnectionsVideo Looping Connections
Set all LTC 8921 Module
Termination Switches inside
First Level LTC 8903 Bays to OFF.
LTC 8902 for Monitors 1 to 64
8 LTC 8934 Video Output Modules are
Required for Monitors 65 to 128.
Set all Termination Switches to ON
on all Modules.
LTC 8902 for Monitors 65 to 128
Video Interconnect
LTC 8809 Cables
Video Interconnect
LTC 8809 Cables
8 LTC 8934 Video Output Modules are
Required for Monitors 1 to 64.
Set all Termination Switches to ON
on all Modules.
16 LTC 8921 Video Input
Modules are Required for
256 Camera Inputs.
Set LTC 8921 Module Termination Switches
in EVEN Numbered Slots to ON (in all Second Level LTC 8903 Bays)
Set LTC 8921 Module Termination Switches
in ODD Numbered Slots to OFF (in all Second Level LTC 8902 Bays)
Figure 8.41: Front View, Module Placement and Termination Settings, 1024 Camera by 128 Monitor System
LTC 8900 Series
Satellite System Configuration Installations | en 97
Bosch Security Systems, Inc. Installation Manual 2016.04 | 10.7 | F.01U.323.096