Operation Manual
Table Of Contents
- Title Page
- Table of Contents
- Safety
- Unpacking
- Product Description
- Overview of Installation Steps
- Configuration Programming in the Shipping Box
- Configuration Programming on a Temporary Table-top Stand
- Mounting Location and Mounting Orientation
- Overview of Mounting Options
- Install the Camera
- Make Connections - Power and Control
- Cant the Camera
- Typical System Configurations
- Configuration
- Configuration via IP, Basic Mode
- Configuration via IP, Advanced Mode
- Advanced Mode: General
- Identification
- Password
- Date/Time
- Display Stamping
- Advanced Mode: Web Interface
- Appearance
- LIVE Functions
- Logging
- Advanced Mode: Camera
- Installer Menu
- Encoder Profile
- Encoder Streams
- Privacy Masks
- Picture Settings
- Lens Settings
- PTZ Settings
- Illumination/Wiper
- Scenes and Tours
- Sectors
- Miscellaneous
- Audio
- Pixel Counter
- Advanced Mode: Recording
- Storage Management
- Recording Profiles
- Maximum Retention Time
- Recording Scheduler
- Recording Status
- Advanced Mode: Alarm
- Alarm Connections
- VCA
- Virtual Masks
- Audio Alarm
- Alarm E-Mail
- Alarm Task Editor
- Alarm Rules
- Advanced Mode: Interfaces
- Alarm Inputs
- Alarm Outputs
- Advanced Mode: Network
- Network Access
- DynDNS
- Advanced
- Network Management
- Multicast
- Image Posting
- Accounts
- IPv4 Filter
- Encryption
- Advanced Mode: Service
- Maintenance
- Licenses
- Diagnostics
- System Overview
- Operation
- Troubleshooting
- Maintenance
- Decommissioning
- Technical data
- Keyboard Commands By Number
- Back Page
Auto pan right limit
Sets the right Auto Pan limit of the camera. Use the preview window to move the camera to
the right pan limit and click the button. The camera will not move past this limit when in Auto
Pan Between Limits mode (AUX 2 ON).
Tilt up limit
Sets the upper tilt limit of the camera. Use the preview window to move the camera to the tilt
limit and click the button.
Tilt limits
Click the Reset button to clear the upper tilt limit.
Tour A / Tour B
Starts and stops the recording of a recorded (guard) tour.
The camera can make up to two (2) recorded tours. A recorded tour saves all manual camera
movements made during the recording, including its rate of pan, tilt and zoom speeds, and
other lens setting changes. The tour does not capture camera video during the recording of
the tour.
Note 1: You can save a total of 15 minutes of recorded actions between the two tours.
To record a tour:
1. Click the Start Recording button. The system prompts you to overwrite the existing tour.
2. Click Yes to overwrite the existing tour movements.
3. Click the View Control link, under the image cameo, to access the directional and zoom
controls.
4. Use the View Control dialog box to make the necessary camera movements.
5. Click the Stop Recording button to save all actions.
North point
Click the Set button to overwrite the existing North point.
Click the Defaults button to reset the North point to factory defaults.
Illumination/Wiper
IR Illuminators
Controls IR illuminators. When ON, the camera gives a much better image at low light levels.
Options are: On, Off, Auto.
IR intensity
Select the percentage of intensity of the infrared (IR) light.
White light illuminators
Select On to enable the White light illuminators.
Select Off to disable the White light illuminators.
White light intensity
Select the degree of intensity of the White light.
Enable White light timeout
Select On to enable a timeout for the White light feature.
Select Off to disable the timeout.
The timeout turns OFF the white lights, after they have been ON but idle for some time, to
help to retain the life of the LEDs.
White light timeout [min]
Select the number of minutes (from 1 to 30) after which the White light will turn off after
activation.
IR focus correction
Optimizes the focus for IR lighting. Options are: On, Off.
Wiper
15.18
62 en | Configuration via IP, Advanced Mode
MIC IP starlight 7000 HD, MIC IP
dynamic 7000 HD
2014.05 | 1.0 | F.01U.291.520 Operation Manual Bosch Security Systems, Inc.